Author: Site Editor Publish Time: 11-10-2026 Origin: Site
Choosing the right gear motor is one of the most important decisions in machine design. An undersized gear reducer fails early; an oversized one wastes energy and money. This guide walks through the three core parameters every engineer should verify: torque, speed ratio (gear ratio) and thermal power.
The basic motor power formula is:
P = (T × n) / 9550
where P is motor power in kW, T is load torque in N·m, and n is output speed in r/min. In real applications, apply a service factor (K = 1.2–2.0) depending on load characteristics: uniform loads (conveyors, fans) use lower values, while medium or heavy shock loads (crushers, mixers, hoists) require higher values.
The speed ratio of a gear reducer is simply:
i = n₁ (input speed) / n₂ (required output speed)
Example: a 1450 r/min motor driving a conveyor at 30 r/min needs a ratio of about 48:1, which can be achieved with a two-stage helical gearbox or a cycloidal (pin-wheel) reducer. Keep the actual ratio within 5% of the theoretical value where possible.
The rated output torque of the gearbox must satisfy:
T₂ = T₁ × i × η (η = transmission efficiency)
Typical efficiency values: planetary gear reducers 0.92–0.97, helical gear units 0.94–0.96, worm gear reducers only 0.7–0.85. For applications with frequent starts, the peak torque must not exceed the rated torque of the gearbox (generally keep short-term overload below 150–200%).
For continuous operation, the allowed thermal power rating of the gear reducer must be higher than the actual transmitted power multiplied by ambient correction factors. Above 40°C ambient temperature, apply a correction factor of 1.1–1.3. If the thermal check fails, consider a larger frame, forced cooling, or a synthetic lubricant.
Mounting: confirm flange size, shaft diameter, hollow/shaft output type and maintenance clearance.
Backlash: precision positioning applications require ≤3 arcmin; general machinery can accept 8 arcmin or more.
Protection: choose IP54 for normal workshops, IP65 or above for dusty or wet environments.
Lubrication: most industrial gear reducers require an oil change every 8,000–10,000 running hours; worm units every 4,000–6,000 hours.
1. Sizing only by motor nameplate power while ignoring cyclical load peaks — use the RMS load method for fluctuating duty cycles.
2. Chasing an overly large ratio in a single stage, which causes efficiency loss and excessive backlash.
3. Ignoring radial load on the output shaft — verify the allowed overhung load against chain sprocket or pulley pulls.
4. Forgetting altitude and ambient temperature derating above 1,000 m.
Following this checklist, engineers can match the right gear motor and gear reducer combination for stable, energy-efficient operation. For help selecting a replacement gearbox compatible with SEW, NORD, BLD cycloidal series and more, contact the WGT Gearbox engineering team — we provide free selection support based on your torque, speed and mounting requirements.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?