Author: Site Editor Publish Time: 11-10-2026 Origin: Site
Belt conveyors are the workhorse of bulk material handling, and the helical gear reducer is the component that decides whether a conveyor starts smoothly or fails under load. This guide explains how to size a conveyor gearbox correctly in five steps.
Start from the belt pull. For a horizontal conveyor, the effective pull is the sum of friction (belt, idlers, load) plus any incline component. Required output torque is:
T = F × D / 2
where F is the effective belt pull in N and D is the pulley diameter in metres. Inclined conveyors must add the gravity component of the load, and starting torque is typically 1.5–2 times running torque.
Motor power follows the standard formula P = (T × n) / 9550, where n is the output speed in r/min. Divide by the transmission efficiency of the gear unit — around 0.94–0.96 for a two-stage helical gearbox, lower for three-stage units and worm gearboxes.
Output speed required by the conveyor = belt speed / pulley circumference. The ratio i = motor speed / output speed. For conveyors, ratios of 10:1 to 60:1 are common:
i up to 8:1 — single stage
i 8:1 to 40:1 — two stage (the most common for conveyor gearboxes)
i 40:1 to 200:1 — three stage
Do not size to running torque alone. Belt conveyors are medium-shock duty: apply a service factor of 1.3–1.6 for uniformly loaded conveyors and 1.6–2.0 for crusher feed, ore or recycled-material duty. The selected gear reducer must have a rated output torque above the calculated value multiplied by this factor.
A gearbox can be mechanically strong yet thermally overloaded in continuous duty. Check the thermal capacity rating against actual transmitted power, corrected for ambient temperature above 40°C and for poor ventilation. Finally, verify that the radial load from chain, belt or pulley pull stays within the allowed overhung load of the output shaft; a shaft-mounted gear motor with a torque arm is often the better choice for long conveyors.
For general belt conveyors, an R-series or F-series parallel shaft helical gear reducer offers high efficiency and easy motor mounting. Where the drive must sit at 90° to the conveyor, a K-series helical-bevel unit solves the layout without a separate right-angle drive. For slow, heavy duty — apron conveyors and bucket elevators — a cycloidal (pin wheel) reducer typically provides the shock resistance needed.
WGT Gearbox manufactures helical gear reducers, helical-bevel gearboxes, cycloidal reducers and gear motors, including units interchangeable with SEW, NORD and other European series. Send us your belt speed, pulley diameter and load, and our engineers will size the correct conveyor gearbox free of charge.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?