Author: Site Editor Publish Time: 18-10-2026 Origin: Site
Every inclined belt is a stored-energy machine. The moment a conveyor gear motor loses power the load does not politely stop: belt tension unwinds like a rubber band, the head pulley reverses and material travels back to the tail. A holdback — also called a backstop or anti-runback clutch — is the one-way device that catches that reversal. It is also the component most often bought from a catalogue line without a calculation behind it, which is why rollback incidents still happen on drives that were supposedly protected.
Reverse torque at the protected shaft is the gravity component of the loaded belt times pulley radius: T = W × R × sinθ. At 5° that component is 8.7% of the load; at 18° it is 31%. Field practice follows the same curve: holdbacks are recommended from roughly 5–10° of incline and treated as mandatory above 18°, and they are equally required on descending regenerative conveyors where the load drives the motor.
Most recognised engineering houses size a holdback on motor breakdown (stalled) torque reflected to the protected shaft, not on running torque. A backstop has essentially zero backlash, so the whole stored-energy pulse arrives at once; sizing to running torque leaves the device to absorb the gap between nominal and stall torque as impact.
The gearbox torque calculation is short. Rated motor torque is T = 9,550 × P / n, multiplied by the breakdown ratio, then by ratio and efficiency to reach the low-speed shaft, then by the selection factor:
Step | 30 kW, 1,500 rpm, i = 25, η = 0.94, breakdown 2.5× | Result |
|---|---|---|
Rated motor torque | 9,550 × 30 / 1,500 | 191 N·m |
Breakdown torque | 191 × 2.5 | 478 N·m |
Reflected to head shaft | 478 × 25 × 0.94 | 11.2 kN·m |
Selection factor 2.2 (quarry duty) | 11.2 × 2.2 | 24.7 kN·m |
Factors in common use run 1.5–2.0 for general conveying and 2.0–2.5 for crusher feed and ore. Where the application allows it, a torque-limiting holdback beats a bigger conventional one: set slipping torque at about 1.3× the true restoring torque and the unit sheds excess tension during an aborted start. In one published case a 950 kW incline damaged a 72 kN·m standard backstop that a 19.6 kN·m slipping setting would have survived.
Type | How it locks | Best fit |
|---|---|---|
Sprag clutch | Tilting sprags wedge between races; centrifugal lift-off cuts drag at speed | Compact high-speed mounting, frequent stops |
Roller-ramp | Rollers climb cam ramps; oil film separates parts while freewheeling | Heavy low-speed head shafts, very high torque |
Centrifugal pawl | Spring pawls throw out into a ratchet ring | Reducer intermediate shafts, non-lubricated |
Ratchet / wedge | Positive tooth engagement | Slow, special-duty or very dusty plants |
Mounting decides overrunning speed, heat and serviceability. The low-speed head pulley shaft opposite the drive is preferred: rpm is lowest, freewheel drag and heat are minimal, and the reducer, coupling and motor can be serviced without reverse torque present. This is the arrangement most overhung load gear reducer head drives use.
A double-extended low-speed reducer shaft is easier to reach but lives with reducer vibration and hotter oil — and carries a hidden risk: if the low-speed coupling fails, the backstop is no longer connected to the pulley and the belt runs back anyway. High-speed mounting on the reducer input solves a space problem and creates a thermal one, because overrunning rpm multiplies by the ratio. In every location the torque arm must react torque and nothing else; clamping or welding it preloads the housing and is a leading cause of premature sprag wear.
On multi-drive conveyors the regenerative torque does not divide evenly — the first drive in the regenerative direction typically carries about 70% of the total while the others freewheel. Where two backstops share a shaft, each should be rated for at least 70% of total reverse torque. It also explains why a holdback choice affects gear life on a gearbox for belt conveyor installation: a load-sharing unit keeps the first gearbox’s gears and bearings from carrying that share while stationary.
Undersized for an aborted start — sized on running torque, destroyed by the first jammed belt.
Reverse orientation — symmetrical housings allow either direction, so the unit freewheels under load.
Constrained torque arm — housing distorted, elements worn on one side.
Oil starvation or water ingress — low level, blocked breather or failed labyrinth; ramps score and engagement turns late and noisy.
Overrunning too fast — high-speed mounting beyond the freewheel rating; drag heat cooks the oil, then the sprags.
Before first run, confirm lock direction by hand against the marked arrow, check oil level at shaft centreline, grease-purge the labyrinth on dusty sites, and verify the torque arm has clearance in the reaction direction. Then put the unit on the route: the gearbox maintenance checklist items that apply are oil level and colour, breather condition, housing temperature, engagement noise and seal weep. A backstop that engages with a bang or runs hot is telling you the freewheel mode is dragging.
A holdback is only as good as the shaft it protects, which is why WGT Gearbox quotes the two together. Our conveyor gear motor range covers inline helical and parallel-shaft units for long belts, helical-bevel K-series for inclined transfer stations, shaft-mounted reducers with torque arms for head-pulley drives, and cycloidal reducers where shock dominates — each with rated and peak torque, thermal rating, overhung load capacity and backstop interface on the data sheet. Send incline angle, belt speed, tonnage, pulley diameter, ratio and motor nameplate for a gearbox quotation and backstop sizing within 24 hours. Need a SEW gearbox replacement or NORD equivalent with the same shaft and flange envelope? A nameplate photo is enough for a free cross-reference. As a China gearbox manufacturer serving conveyors, mining and port handling, we can also run the case through our online gearbox selection tool.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?