Author: Site Editor Publish Time: 14-10-2026 Origin: Site
Two identical gear reducers — same ratio, same power, same brand — and one runs for 60,000 hours while the other leaks oil and destroys its output bearings within a year. The difference is rarely quality. It is the gearbox mounting position. Fill oil to the sight glass of a horizontally commissioned unit, then bolt that unit to a wall or hang it from a ceiling, and the oil level and breather end up in the wrong place: upper bearings run dry while internal pressure forces oil past the seals. This guide covers the M1–M6 codes and how to specify the right orientation.
The codes describe how the housing sits relative to gravity — not how it is bolted to the machine. Definitions vary between manufacturers, so treat the table below as the common European convention (SEW R/F/K/S and NORD SK series) for gearbox mounting position M1 M6:
Code | Housing orientation | Typical mounting | Main risk if ignored |
|---|---|---|---|
M1 | Horizontal, feet down | Foot / base plate | Reference position, standard oil fill |
M2 | Horizontal, feet up (hanging) | Foot / ceiling bracket | Breather and level plug must move |
M3 | Vertical, output shaft down | Flange | Lower seal submerged in oil |
M4 | Vertical, output shaft up | Flange | Upper bearings starved of oil |
M5 | Wall horizontal, flange side | Flange | Oil pools away from the level glass |
M6 | Wall horizontal, rotated 180° | Flange | Breather below the oil line |
Note that SEW X-series industrial units group their positions differently (M1/M3 horizontal, M5/M6 vertical, M4/M2 upright), and NORD MAXXDRIVE defines them by housing design and stage count. Never copy a code between catalogues — check the diagram of the exact unit you are buying.
Breather / vent plug — must sit at the highest point. If the transport plug is left in, heat expansion pressurises the casing and forces oil past the seals: the most common cause of a gear reducer leak on a new vertical unit.
Oil level plug or sight glass — defines the correct oil height for that orientation only. A valid reading in M1 is meaningless in M3.
Drain plug — at the lowest practical point, so old oil and wear particles flush out completely at every gearbox oil change.
State the mounting position on the order data sheet and ask the factory to ship the unit with plugs pre-arranged. Moving a breather on site is possible on most cast-iron housings, but every port you open is another leak path.
A vertically mounted unit normally needs more oil than the same housing laid flat, because lubricant must reach gear meshes and bearings sitting higher inside the casing. Worm units show the extremes: worm-under can need up to 50% more oil than worm-over, since the bronze wheel then depends entirely on splash lubrication. Never fill to the top — overfilling causes churning losses, foaming, higher temperature and seal leakage. Use the quantity printed for your size, ratio and position, then confirm through the sight glass after a few hours of running as part of a routine gearbox maintenance checklist.
The mounting surface is the physical interface: foot mounted, flange mounted, or shaft mounted (hollow shaft over the driven shaft, restrained by a torque arm). The mounting position is the orientation of the whole unit relative to gravity. A unit can be flange mounted in M3 or in M5; a foot-mounted gearbox can still hang from a ceiling in M2. Specify both, or your supplier is guessing and the oil fill will be wrong.
Turning a helical gearbox through 90° is not just rotating it on the pallet. Vertical duty changes how oil reaches the upper bearings, how the lower seal is wetted, and how axial loads from impellers, hoisting ropes or screw flights are carried. Purpose-built vertical units add thrust bearings and longer bearing spans; a standard horizontal unit turned on site may have neither. Check the motor end too: shaft-up / shaft-down bearing suitability, terminal box position, cooling-air clearance and drain holes. A heavy vertical motor should be supported independently, not hung entirely from the input flange.
Confirm the ordered position code against the site drawing, not against a photo of the old unit.
Check the mounting surface is flat (typically within 0.1 mm/m) and clean; tighten bolts diagonally in stages.
Move the breather to the highest point and remove every transport plug.
Verify the level plug or sight glass reads at the mark; top up with the specified gear oil quantity for that position.
Align the input coupling within the tolerance on the instruction sheet — misalignment is a leading cause of gearbox noise.
Fit the torque arm in the approved position, free of binding and able to react full output torque.
After the first 50–100 hours, re-check bolt torque, oil level and seals.
Take the gearbox mounting position from the site drawing into the RFQ, together with the mounting surface, motor orientation and driven equipment. That single line prevents the most expensive installation error — a good gear reducer running in an orientation it was never lubricated for.
As a China gearbox manufacturer in Hangzhou, WGT Gearbox supplies helical, helical-bevel and parallel-shaft units, cycloidal pinwheel reducers, worm reducers and gear motors in all six mounting positions, with matched oil volume and plug configuration for your orientation, plus drop-in interchangeability for SEW and NORD series. Send your mounting drawing or nameplate photo for a free cross-reference and a complete gearbox quotation with drawings within 24 hours — or compare frame sizes first with our online gearbox selection tool.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?