Author: Site Editor Publish Time: 24-10-2026 Origin: Site
Gear motor sizing for mixers fails more often than conveyor or pump sizing because the load is defined by the process fluid, not by a fixed machine rating. A drive chosen from the nameplate kilowatts of a similar mixer can be badly undersized once the real mixer gearbox duty is understood: viscosity rises during reaction, solids settle during downtime, and every batch starts from standstill. This guide walks through the four checks that matter — process torque, viscosity-based service factor, batch startup margin and output bearing loads — with worked numbers you can reproduce.
Mixing power follows the impeller power-number correlation:
P = Np × ρ × N³ × D⁵, then T (Nm) = 9550 × P (kW) ÷ N (rpm)
Torque, not motor horsepower, is what you match against the gearbox rated output torque. Two motors with identical power but different output speeds need very different gearboxes, because torque and speed are inversely related. Typical values for common impellers:
Impeller type | Power number Np | Typical speed | Load character |
|---|---|---|---|
Hydrofoil (axial) | 0.3–0.5 | 80–150 rpm | Smooth, low shear |
Pitched-blade turbine 45° | 1.2–1.4 | 60–120 rpm | Moderate, general purpose |
Rushton disc turbine | 4.5–5.5 | 50–100 rpm | High shear, radial flow |
Anchor / ribbon | Varies widely | 10–40 rpm | High torque, close clearance |
A service factor gearbox selected at 1.5 for a water-like blend is a common and costly mistake. The service factor should follow the worst credible viscosity of the recipe, not the average:
Process viscosity | Typical products | Recommended service factor |
|---|---|---|
Below 100 cP | Water, solvents, light blends | 1.5 |
100–10,000 cP | Pastes, slurries, paints | 2.0 |
Above 10,000 cP | Heavy sludge, filled polymers, dough | 2.5–3.0 |
The reason is the start condition. A turbine impeller starting in a 5,000 cP slurry can demand 4–6× the steady-state running torque. A drive sized for running torque at SF 1.5 therefore starts every batch at 2.5–4× rated torque, accumulating fatigue damage that surfaces as early gear tooth failure.
Batch duty adds three load cases that continuous ratings do not cover:
Breakaway torque: settled solids and yield-stress fluids need 20–40% above running torque before flow begins — more if tanks sit idle between batches.
Starts per hour: frequent batch starts multiply thermal duty on the motor; class F or H insulation and an IE3 motor hold up far better than standard frames.
VFD ramp-up: an acceleration ramp of 15–30 s lets a gear motor ride through the loaded start, but confirm continuous torque and motor cooling at minimum mixing speed, where self-ventilation collapses.
For high-viscosity recipes, budget one VFD frame above motor nameplate to give peak-current headroom during the breakaway phase.
Take a 5,000-litre tank with a 45° pitched-blade turbine: Np = 1.27, ρ = 1,000 kg/m³, N = 90 rpm, D = 0.7 m.
Step | Calculation | Result |
|---|---|---|
Impeller power | P = 1.27 × 1000 × 1.5³ × 0.7⁵ | ≈ 0.72 kW |
Add 10% losses + 25% margin | 0.72 × 1.375, round up | 1.1 kW motor |
Output torque | 9550 × 1.1 ÷ 90 | ≈ 117 Nm |
Apply SF 1.5 | 117 × 1.5 | 175 Nm gearbox rating |
The selection target is a helical agitator gearbox rated for at least 175 Nm at 90 rpm, vertical hollow-shaft with integral thrust bearing. For the same tank filled with a 10,000 cP paste, SF 2.5 pushes the requirement to roughly 290 Nm — a full frame size larger, chosen before the first batch ever runs.
Mixer gearboxes see continuous combined radial and axial loads that most catalogues list separately. Top-entry drives carry impeller thrust and shaft weight straight into the output bearing; side-entry units see fluid reaction thrust of several kilonewtons along the shaft axis. Always submit the combined torque-plus-thrust duty to the manufacturer for an output bearing life check — a torque-only catalogue selection will not flag this failure mode.
Sound gear motor sizing for mixers comes down to one discipline: select from the worst credible process state — full batch, settled solids, cold product — never from the clean-water commissioning test. Send us your recipe (viscosity range, tank dimensions, impeller type, starts per hour) and our engineers will size the drive and verify the output bearings free of charge. Hangzhou WGT Transmission supplies helical, helical-bevel, worm and planetary gear motors and gearboxes for mixer, agitator and reactor duty, including SEW and NORD compatible replacements with matched flanges and torque ratings, so a failed imported drive can be replaced without re-engineering the vessel.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?