Author: Site Editor Publish Time: 15-10-2026 Origin: Site
The noise of the reducer suddenly becomes louder, which is an early warning signal given by the equipment before it officially fails. A common practice on site is to shut down the machine first and then disassemble it. As a result, no problem can be found after disassembly, but new problems arise when it is put back together. Noise is not the name of a fault, but the external manifestation of a set of symptoms. Different rhythms and frequency bands point to the four directions of gears, bearings, alignment and lubrication respectively. This article organizes the on-site treatment of reducer noise into a five-step troubleshooting method. From simple to complex, most reducer faults can be located in the general location without dismantling the machine.
Record before the investigation. This step determines the accuracy of subsequent judgments. It is necessary to write clearly: whether the noise occurs without load or with load, whether it occurs during speed increase or steady-state operation, whether it changes with the speed cycle, whether it is accompanied by temperature rise or output decrease. Abnormal noise from the same reducer only occurs when it is fully loaded and depends on alignment, foundation stiffness and overload. If it occurs when no load is present, it is more likely to come from the internal assembly and bearings. It is also necessary to confirm whether the noise is new, whether the lubricating oil or coupling has been changed recently, and whether it only occurs in a certain speed range and is significantly reduced after deviation. If it meets the third point, structural resonance should be suspected first, rather than part damage.
The following five steps are arranged in order of "free disassembly first, from simple to complex". Each step has a clear judgment object. If an exception is found at any step, it can be transferred to processing.
Step 1: No need to dismantle the appearance and oil inspection. After stopping the machine to cool down, check the seams of the casing, the shaft extension end and the oil drain plug for leaks, and check whether the connecting bolts on the foot, end cover and motor are loose. Release a small amount of oil and observe: if it turns black, emulsified and white, or contains metal debris, it indicates that there has been abrasive wear or water intrusion. The noise is mostly caused by the decrease in lubrication ability. When the oil level is lower than the lower mark of the oil level, add gear oil of the same brand. It is strictly prohibited to mix oils of different viscosity grades.
Step 2: Listen to the sound to identify the location and touch the temperature. Use a listening needle or a long-handled screwdriver, and place the blade against the upper part of the gear box and the bearing seat respectively to listen: if the upper part makes a louder sound, check the gear meshing, and if the bearing seat makes a louder sound, check the bearing. At the same time, measure the temperature of the bearing seat with the back of your hand or an infrared thermometer. If it exceeds the ambient temperature by more than 40°C, or the surface exceeds 80°C, it can basically confirm that lubrication failure or bearing jamming occurs. The temperature difference between the bearing seats at both ends of the same equipment exceeds 8°C, which indicates uneven load distribution or that the bearing on one side is damaged.
Step 3: Change working conditions and separate. Disconnect the load and manually turn the car to feel if there is any resistance mutation point on the input shaft. The stuck point usually corresponds to bearing bite or tooth surface collision. Then disengage the coupling and run the motor independently without load to distinguish whether the noise comes from the motor or the reducer: if there is abnormal noise under no load, it points to the inside of the reducer. Finally, load in steps of 25%, 50%, 75%, and 100% of the rated load. Each section runs for about 30 minutes to record the changes in sound pressure and vibration. If the noise suddenly rises in a certain load section, focus on rechecking the alignment and tooth surface contact.
Step 4: Instrument quantification and characteristic frequency comparison. Acceleration sensors are used to collect vibrations in the three directions of horizontal, vertical and axial directions at key positions of the bearing seat and box, and analysis is done in the time domain and frequency domain. Gear defects are characterized by sidebands separated by shaft rotation frequency on both sides of the meshing frequency; bearing defects are characterized by independent peaks at the failure frequencies of the inner ring, outer ring or rolling elements. By comparing the abnormal peak values with the theoretical characteristic frequencies one by one, you can determine which gear or bearing the noise comes from. This is a key step in changing the reducer noise from 'feeling loud' to 'knowing where the problem is'.
Step 5: Disassembly, inspection, confirmation and repair and re-inspection. After locking the range, disassemble and inspect, focusing on whether there are pitting pits and stepped wear on the tooth surface, whether the bearing raceway is peeled off, whether the key and keyway are loose, and whether there are any iron filings left inside. After the processing is completed, do not directly put it into operation at full load: first run without load for 30 minutes to confirm that the abnormal noise disappears, then load up to the rated load according to the steps, and compare the retest spectrum with the data before shutdown and archive it as the baseline for the next reducer maintenance .
Preliminary attribution can be made without the need for instruments on site. The rhythm and timbre of the noise itself are clues.
Noise characteristics |
High probability source |
Priority check items |
|---|---|---|
Continuous and even buzzing, which gets worse as the rotational speed increases. |
Gear meshing clearance is too large and tooth surface is worn |
Oil level, oil quality, gear backlash |
Periodic knocking or banging sounds, the faster the speed, the higher the frequency |
Tooth surface pitting, tooth chipping, coupling eccentricity or key looseness |
Tooth surface condition, key and keyway clearance |
A high-pitched whistling or squeaking sound |
Direct metal contact due to poor lubrication |
Oil film state, oil viscosity |
Intermittent dull thumping sound, obvious when starting and stopping |
Load impact, pin tooth pin wear, elastic parts aging |
Working condition impact frequency, needle tooth sleeve |
The overall vibration of the box is accompanied by noisy noises |
Loose foundation, insufficient foundation stiffness, internal debris |
Anchor bolts, foundation flatness |
Only by converting the subjective listening experience into comparable numbers can we have a basis for subsequent trend judgments. The following values are for preliminary on-site judgment. The specific limits should be based on the documentation and working conditions that come with the equipment.
Monitoring items |
Reference threshold |
meaning |
|---|---|---|
Vibration speed effective value |
Greater than 4.5 mm/s |
It indicates abnormal gear meshing or misalignment of the shaft system. |
Vibration acceleration |
Greater than 15 m/s² |
Prompts impact defects such as bearing peeling |
Bearing seat temperature rise |
40℃ higher than the environment or 80℃ higher than the surface |
Lubrication failure or bearing sticking |
Temperature difference between two bearing seats |
Greater than 8~10℃ |
Uneven load distribution or bearing damage on one side |
Coupling alignment deviation |
Not more than 0.05 mm/m |
Misalignment is a common source of periodic noise |
Gear backlash and tooth thickness |
Exceeded design value by 20%, tooth thickness wear exceeded 10% |
Consider adjusting or replacing the gear pair |
Metal wear debris in oil |
Increase or appearance of flaky or lumpy particles |
Wear has entered an accelerated stage, and the oil should be changed and reviewed immediately. |
One is to equate noise with damage. Loud sound does not mean immediate failure. Some noise comes from normal meshing excitation or resonance. As long as the trend is stable and there are no abnormalities in temperature and vibration, it can be included in monitoring and continued operation. The second is to just change without checking. When determining the need for reducer bearing replacement , if the bearing seat hole fit and journal condition are not checked at the same time, the new bearing will often be repeatedly damaged within a short period. The third is to ignore external factors. The misalignment of the reducer coupling , loosening of the foundation and deformation of the foundation will all appear in the form of noise, and it is easy to go without a solution for a long time only by looking for the cause internally.
Incorporating noise troubleshooting into daily reducer maintenance will save costs: it is recommended to record noise and vibration data every 1,000 to 1,500 hours of operation, and shorten the time to 500 hours for conditions with heavy dust, frequent forward and reverse rotation, or long-term full load, and focus on tracking trends rather than single values. A slow upward trend indicates steady development of wear, while a short-term jump often corresponds to sudden assembly looseness or parts damage.
Back to the original question - what should I do if the noise of the reducer becomes louder? The answer is not to dismantle the machine immediately, but to straighten out the order of inspection: first record the working condition boundary, then check the oil and tightening without dismantling, then listen to the sound to identify the position and measure the temperature, then use variable working condition separation and spectrum analysis to lock the position, and finally disassemble and confirm and re-inspect according to standards. The noise mechanisms of cycloidal pinwheel reducers, hard tooth surface reducers and various gear reduction motors are similar. By mastering this sequence, most on-site problems can be solved at a stage with low downtime costs.
Hangzhou Weigao Transmission Machinery Co., Ltd. specializes in the manufacturing of transmission equipment. It is a reducer manufacturer that integrates R&D, production and supporting services . The product line covers cycloidal pinwheel reducers, hard tooth surface reducers, coaxial reducers, worm gear reducers and gear reduction motors. It can provide fault diagnosis assistance, spare parts matching and model comparison for old machine replacement for conveying, lifting, mixing, metallurgy and other working conditions. If you are experiencing persistent abnormal noise, high temperature rise, or reduced output, send us the photo of the reducer nameplate, installation posture, and on-site noise video, and we will provide free reducer consultation and treatment suggestions. As based in Hangzhou a Hangzhou reducer manufacturer , we also welcome drawings and samples to customize and negotiate complete machine packages.
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?
Fertilizer Plant Gearbox: Turnaround Season Demand and Sizing Guide