Author: Site Editor Publish Time: 14-10-2026 Origin: Site
Walk through any chemical, petrochemical or pharmaceutical plant and you will find drive packages where a standard gear motor is simply not legal. The atmosphere itself is the hazard: a leaking flange, a solvent drum, a reactor vent. Every electrical device in that area — including the motor on the agitator, pump or conveyor — must be built so that a spark or a hot surface can never ignite the surrounding gas. That is what an explosion proof gear motor delivers, and the code Ex d IIB T4 is the specification most chemical plants end up buying. Understanding each token of that marking, and how it interacts with the gearbox bolted to the motor, is the difference between a compliant installation and a rejected delivery.
A full marking usually reads something like II 2G Ex d IIB T4 Gb. Read it left to right:
II — equipment group II, all surface industries (group I is mining).
2G — ATEX category 2 for gas, the entry ticket to Zone 1 and Zone 2.
Ex d — flameproof enclosure per IEC 60079-1. An internal ignition is contained inside the housing and the flame is cooled as it escapes through a precision-machined flame path.
IIB — gas group: IIA is propane and methane, IIB is ethylene class, IIC is hydrogen and acetylene, the most onerous.
T4 — temperature class, maximum surface temperature 135 °C in service and under fault.
Gb — equipment protection level, confirming Zone 1 and Zone 2 suitability.
The ATEX gearbox and motor assembly you finally install must carry a marking equal to or better than the area classification drawing of the plant. Over-specifying is always legal; under-specifying never is.
Temperature class |
Max surface temp |
Typical media |
|---|---|---|
T1 |
450 °C |
Hydrogen, methane |
T2 |
300 °C |
Common industrial solvents |
T3 |
200 °C |
Petrol vapour, most hydrocarbons |
T4 |
135 °C |
Most refinery and chemical plant gases |
T5 |
100 °C |
Low auto-ignition vapours |
T6 |
85 °C |
Carbon disulphide (auto-ignition ~90 °C) |
Gas group |
Representative gases |
Notes |
|---|---|---|
IIA |
Propane, butane, methane |
Lowest test energy |
IIB |
Ethylene, diethyl ether |
Workhorse for chemical plants |
IIC |
Hydrogen, acetylene |
Strictest flame-path test, higher frame cost |
T4 with group IIB covers the overwhelming majority of chemical plant duty, which is exactly why Ex d IIB T4 has become the workhorse specification. If the process handles carbon disulphide, hydrogen or acetylene, the frame steps up to T5/T6 or IIC — and costs more, because a lower surface limit forces a larger frame for the same output.
Take the area classification first, not the catalogue. Get the zone drawing from the plant engineer: Zone 1 (likely during normal operation) versus Zone 2 (unlikely, brief). Zone decides whether you need Ex d or the cheaper Ex e protection.
Match gas group and temperature class to the actual medium. List every flammable substance that can be present and take the lowest auto-ignition temperature. The nameplate T-class must sit safely below that value.
Size the drive, then re-check it with the protection penalty. Hazardous area motors are derated because of restricted cooling and longer flame-path housings. Run a full gear motor selection calculation — output torque, speed ratio, thermal power rating and service factor — using the derated motor power.
Specify the gearbox for the same environment. The reducer needs IP55 (IP65 in wash-down and coastal duty), a breather arranged for the mounting position so oil cannot leak onto hot surfaces, and an oil fill that stays within the T-class limit. Explosion-proof motors are frequently paired with helical, helical-bevel or worm gear reducer units, because the output bearing must also survive mixer and agitator side loads.
Get the certificates before the shipment. EU projects need the ATEX EU-type examination certificate plus the declaration of conformity; export projects are usually safer with an IECEx certificate. An ATEX gearbox package without matching documentation will be refused at site acceptance.
Certification is not a permanent state. Flame paths, terminal box gaskets, cable glands and breather elements all degrade, and IEC 60079-17 sets out the inspection regime that keeps the marking valid. Build a gearbox maintenance checklist around four items: verify all flame-path fasteners to the certified torque; confirm cable glands are the certified type and correctly sealed; measure surface temperature under real load rather than assuming it; and inspect the breather and seals for leaks that could coat the enclosure. Any repair that opens the flame path must return the unit to its certified condition — unauthorised field machining voids the certificate and the insurance cover with it.
An explosion proof gear motor is not an accessory added at the end of a project. Zone classification, gas group, temperature class, derated motor sizing, gearbox sealing and certification paperwork all have to line up before the first drawing is released. Get them aligned and the drive runs for years without a compliance question; get one wrong and the whole package is rejected at the gate.
As a China gearbox manufacturer based in Hangzhou, WGT Gearbox supplies explosion-proof gear motors together with cycloidal pinwheel reducers, hard tooth surface helical and bevel-helical units, worm gear reducers and shaft-mounted drives — plus full drop-in replacement capability for SEW and NORD series. Send us your nameplate photo or area classification drawing, and our engineers will return a complete gearbox quotation with certification documents and technical drawings within 24 hours.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?