Author: Vigo Spread Publish Time: 26-10-2021 Origin: 威戈传播
Reducers can be seen in many machines.A good reducer can improve the service life and bearing capacity of the body.According to the structural characteristics of precision reducers and the load performance of gears, hard gears should be widely used.There are many heat treatment methods to obtain hardened gears.Such as surface quenching, overall quenching, carburizing and quenching, nitriding, etc., should be selected according to the characteristics of the gear reducer.The precision planetary reducer is composed of three transmission structures: planetary gear, sun gear and internal gear ring.Proper heat dissipation method helps to improve the working efficiency of the equipment.The correct way of cooling helps to improve the working efficiency of the equipment.There are three cooling methods.
1. Surface quenching
There are two common surface hardening methods: induction hardening (for small size gears) and flame hardening (for large size gears).Works well when the surface quenching of the hardened layer includes the bottom of the tooth root.Tooth surface hardness can reach 45-55HRC
2. Nitriding
The use of nitrogen ensures that the gear can achieve high tooth surface hardness and wear resistance under the condition of small deformation.After heat treatment, the bearing capacity is improved without a good finish.
3. Carburizing and quenching
Carburized and quenched gears have a relatively large load-bearing capacity, but a finishing process (gear grinding) must be used to eliminate heat treatment distortion to ensure accuracy.Carburized and quenched gears are usually made of alloy steel with a carbon content of 0.2% - 0.3% in carburizing.The hardness of the tooth surface is usually in the range of 58-62HRC.If it is lower than 57HRC, the hard surface strength is significantly reduced, and if it is higher than 62 hours, the brittleness increases.The hardness of carburized and quenched gears gradually decreases from the gear surface to the deep layer, and the effective carburizing depth is specified as the depth from the surface to the hardness of 5.25Hrc.
The effect of carburizing and quenching on the bending fatigue strength of gears not only increases the hardness of the core, but also localizes the residual compressive stress on the surface.It reduces stress in areas of high compressive stress, so the dedendum cannot be ground during gear grinding.
1. Natural cooling
When the universal box cannot meet the heat dissipation requirements, cooling fins can be added outside the box, and the setting of the cooling fins should allow the air to circulate naturally.
2. Fan cooling
If the natural cooling of a separate planetary gear box is not sufficient, a fan can be used for cooling.
3. Water cooling
The oil pool of the precision planetary reducer is equipped with a serpentine water pipe.Serpentine water pipes are usually made of red copper or brass.The pipes are filled with cooling water, which takes up part of the air in the lubricating oil.
Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand
Lubrication and maintenance characteristics of B series industrial gearboxes
What are the common misunderstandings in B series gearbox maintenance?
Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor
How does the R series helical gear reducer perform in a strong vibration environment Selection
Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand
Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart
Is there any way to reduce the parallelism error of the reducer?
Food and Beverage Gearbox Market 2027: Renovation Demand and Mixer Sizing
Marine Deck Winch Gearbox Selection: Drum Torque, Duty Class and Holding Brake
What specific damage will reversal with load cause to the BWY27-59-4KW cycloidal pinwheel reducer?
How to avoid XLED32-841-0.37KW cycloidal pinwheel reducer with load reversal
Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand
What are the common problems with NGW42-25 planetary reducer base welding?
What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?
Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque
Which is more efficient, cycloidal pinwheel reducer or worm gear reducer?