WeiGao Transmission
Email: sales@wgt.net.cn
Language
通栏图2
tonglantu.jpg
Home / News / Belt conveyor reducer Selection calculation example explanation - Hangzhou Weigao Transmission

Belt conveyor reducer Selection calculation example explanation - Hangzhou Weigao Transmission

Author: Site Editor     Publish Time: 13-10-2026      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

The belt conveyor is one of the most commonly used equipment in bulk material transportation, and the accurate selection of the reducer in the drive system directly determines whether the entire line can start smoothly and run for a long time. Many on-site problems (overload tripping, high oil temperature, early pitting corrosion on the tooth surface) are traced back to improper parameter values ​​in the Selection calculation stage. This article takes a general belt conveyor as an example to completely calculate the entire calculation process of the reducer Selection for engineers' reference.

1. Example working conditions and known parameters

Assume a horizontal conveyor belt conveyor: belt speed v = 1.6 m/s, driving drum diameter D = 500 mm, effective circumferential force F = 6000 N, motor is 4 poles (rated speed 1460 r/min), continuous operation for more than 16 hours a day, and the load is moderate impact. First list the core parameter table:

parameter

symbol

value

belt speed

v

1.6 m/s

Drum diameter

D

0.5m

effective circular force

F

6000N

Motor rated speed

n₁

1460 r/min

Transmission total efficiency

η

About 0.95 (two-stage cylindrical gear)

Step 2: Calculation of reducer speed ratio

The drum speed is determined by the belt speed and drum diameter: n₂ = 60v / (πD) = 60×1.6 / (3.1416×0.5) ≈ 61.1 r/min. based on this Calculate the speed ratio of the reducer : i = n₁/n₂ = 1460/61.1 ≈ 23.9. The actual order should take the standard speed ratio of 25 (two-stage transmission). At this time, the actual belt speed deviation is about 4.4%, which is within the allowable range of ±5% and will not affect the process requirements.

Step 3: Calibration of output torque and motor power

The required torque of the drum shaft is T₂ = F×D/2 = 6000×0.25 = 1500 N·m. The commonly used reducer torque calculation formula T = 9550×P/n can be used to calculate the power in reverse: P₂ = 1500×61.1/9550 ≈ 9.6 kW. After taking into account the transmission efficiency, P₁ = 9.6/0.95 ≈ 10.1 kW, so the motor takes the standard power of 11 kW (4 poles). When conveying at an angle, the gravity component of the material must be superimposed, and the starting torque (usually 1.5~2 times the operating torque) must be calibrated to prevent the frequency converter from frequently reporting overload.

Step 4: Reducer service coefficient correction

You cannot just press the operating torque Selection. The service coefficient of the reducer (working condition coefficient K A ) is used to cover the effects of starting shock, load fluctuations and daily operating hours: uniform load transportation is generally taken as 1.3~1.5, and heavy impact conditions such as ore and waste materials are taken as 1.6~2.0. In this example, the operation is more than 16 hours a day and the impact is moderate. If K A =1.5, the required rated output torque is ≥ 1500×1.5 = 2250 N·m. When checking samples, the allowable output torque of the candidate conveyor reducer at the corresponding input speed must not be lower than this value.

Step 5: Confirmation of thermal power and structural type

Sufficient mechanical strength does not mean sufficient thermal margin. The sample thermal power must be checked under continuous full load conditions PG : when the ambient temperature exceeds 40°C, the factory ventilation is poor, or it is installed in a standing position, it needs to be corrected according to the manufacturer's table. If the thermal power is insufficient, increase the frame size or install a cooling fan or forced lubrication. Structurally, hardened cylindrical gear reducers are often chosen for long-distance conveyors (high efficiency and large load-bearing capacity). When space is limited or a right-angle arrangement is required, a spiral bevel gear structure can be considered; at the same time, confirm the cantilever load of the output shaft, the backstop (to prevent reversal of inclined conveying) and the sealing protection level (IP55 or above is recommended for dusty environments).

FAQ

Question: The speed ratio is calculated as 23.9. Can I choose the standard value of 22.4?
Answer: The actual belt speed needs to be back-calculated. If the deviation exceeds ±5%, it will significantly affect the output and motor load rate. In this case, 25 should be given priority, or the non-standard speed ratio should be confirmed with the manufacturer.

Question: Why do we need to do thermal power calibration after Selection?
Answer: The heat dissipation conditions of a continuously operating conveyor are limited. When the mechanical power is sufficient but the thermal power is insufficient, the oil temperature will continue to rise, leading to lubrication failure. This is the root cause of many early tooth surface gluing.

Conclusion

A complete reducer Selection calculation chain is: working condition parameters → speed ratio calculation → torque and power calculation → service coefficient correction → thermal power and cantilever load check. Only by leaving enough margin in every step can the equipment run stably for a long time. Hangzhou Weigao Transmission provides reducer Selection consultation and free Selection services. The product line covers hard-toothed cylindrical gear reducers, cycloidal pinwheel reducers, worm gear reducers and various gear reduction motors. You are welcome to send us your belt speed, drum diameter and load parameters. Our engineers will calculate and recommend suitable models for you according to the above process.

Latest News

WeiGao Transmission

Weigao Gear Reducer is an alliance group company that integrates research and development, production, sales, and service

+86 400 801 9158

Email: sales@wgt.net.cn;wgt.net.cn@gmail.com
Tel:+86571 85023000

WEIGAO REDUCER

FEEDBACK