WeiGao Transmission
Email: sales@wgt.net.cn
Language
通栏图2
tonglantu.jpg
Home / News

News Center

  • How to install a shaft-mounted reducer

    2023-04-14

    How to install a shaft-mounted geared motor.Here we mainly explain the installation relationship between the shaft-mounted geared motor and the working machine, the connection between the shaft-mounted geared motor and the working machine, and the installation of the counter-torque bracket.The following is a Shanghai reducer to describe in detail how to install it.1. The installation relationship between the shaft-mounted deceleration motor and the working machine In order to avoid the bending of the main shaft of the working machine and the additional force on the bearing of the reducer, the distance between the reducer and the working machine should be as far as possible without affecting the normal work. Small, its value is 5-10mm.2. The connection between the shaft-mounted deceleration motor and the working machine. The reducer is directly set on the main shaft of the working machine. When the reducer is running, the reaction torque acting on the reducer box is installed on the reducer box. Other ways to balance.The machine is directly matched, and the other end is connected with the fixed bracket.3. The installation of the anti-torque bracket The anti-torque bracket should be installed on the side of the working machine facing the reducer, so as to Read More
  • Why does the planetary reducer have a broken shaft?

    2023-04-14

    Why does the planetary reducer have a broken shaft?The first possible problem with a large broken shaft is the quality of the planetary reducer.Of course, this is what we ordinary people can think of, and the main reason is the reason that occurs during the usual use.For example, what should we pay attention to during the acceleration and deceleration process of using the planetary reducer, and what is the best way.1. Some applications must strictly abide by this criterion. This is not only to protect the reducer, but more importantly, to prevent the output shaft of the planetary reducer from being twisted.This is mainly because, if there is a problem with the installation of the equipment, the output shaft of the reducer and its load are stuck, and the overload capacity of the driving motor will still increase its output, which may cause the output bearing of the reducer to be damaged. The output shaft of the reducer is twisted off if the force exceeds 2 times its rated output torque.2. In the process of acceleration and deceleration, if the instantaneous torque multiplied by the output shaft of the planetary reducer Read More
  • How to install planetary reducer?

    2023-04-07

    In the reducer, the planetary gear reducer has the characteristics of light weight, small size, wide range of transmission ratio, high efficiency, stable operation, low noise and strong adaptability, so it is widely used in metallurgy, mining, lifting transportation, electric power , energy, building materials, light industry, transportation and other industrial sectors.However, the planetary reducer must be installed before use.Improper installation may cause the output shaft of the reducer to break, causing unnecessary economic losses to the enterprise.In order to let everyone better understand the installation steps and reduce unnecessary economic losses, today Jiangsu Juzhili will take you to understand the installation steps and precautions of the planetary reducer.1. Installation 1. Step 1: Before installation, confirm whether the motor and reducer are in good condition, and strictly check whether the dimensions of the components connected to the motor and reducer match.The following are the dimensions and fit tolerances of the motor positioning boss, input shaft, and reducer slot.2. Step 2: Unscrew the outer flange of the reducer Read More
  • How to calculate the torque of the reducer?

    2023-04-07

    The torque of the reducer is the output torque of the motor, which is one of the basic parameters of the motor.The torque of the reducer is inseparable from the motor speed, power and other factors.Today Jiangsu Juzhili will take you to understand the commonly used torque formula and the calculation of servo motor torque.Hope the knowledge we share can help you.1. Formula: T=9550P/n The formula commonly used in engineering: torque; power; calculation formula for the relationship between speed.Among them: t-torque; 9550-constant (no need to investigate its source); p-motor power (kw); n-output speed (rev/min) Note: It should be noted that the gear transmission should be considered when calculating the torque through the reducer factor of efficiency loss.4. The torque calculation formula of the servo motor is: T=F*R*reduction ratio.Example: Driving a 100kg object, R=50mm, reduction ratio: 1: 50, 3. Regarding the reduction ratio: Read More
  • Installation steps of cycloidal wheel in cycloidal pinwheel reducer

    2023-04-07

    The entire transmission device of the cycloid reducer can be divided into three parts: input part, deceleration part and output part.Installation steps: 1. Check whether the two cycloidal wheels are a pair. The production of the cycloidal wheel is based on a pair, that is to say, the two pieces of the cycloidal wheel are not separated during the production process.When installing, the concept of a pair is that the two cycloidal wheels can completely overlap.Including the bearing hole, the ten holes (shaft pin hole) and the external tooth shape are safe coincidence at the same time, and it looks like one piece from the front. If they can overlap, it proves to be a pair. If they cannot overlap, it proves that they are not a pair and cannot be used.Note that cycloidal wheels have pros and cons, and there are marks on the cycloidal wheels, and the marks of each pair of cycloidal wheels are also different.2. Rotate one of the cycloid wheels by 180°, that is, when the middle bearing holes are completely overlapped, the outer tooth shape is just misaligned, and the heel position of the upper piece is exactly the tooth top position of the lower piece.Note that the relative positions of these two wheels must be remembered. Read More
  • How to prevent reducer gear damage?

    2022-12-20

    How to prevent reducer gear damage?1. Analysis of tooth breakage elements: gear breakage is divided into fatigue breakage and overload breakage.During the working of the gear transmission, the gear teeth are subjected to alternating loads for many times, and the bending fatigue stress acts on the risk section of the tooth root, and fatigue cracks occur at the tooth root. Under the action of the alternating bending fatigue stress, the fatigue cracks gradually Widening, after all, will cause the teeth to bend and break due to fatigue; during the gear transmission, if the gear is subjected to short-term overload, or impact load, or the teeth are severely worn and thinned, overload and breakage will occur. Treatment method: increase the transition circle of the tooth root Corner radius, reducing the value of the surface roughness to be processed as much as possible can reduce the influence of stress convergence, increase the stiffness of the shaft and support, and ease the load on the tooth surface; make the center of the gear tooth have sufficient toughness; Appropriate strengthening treatment at the root can improve the fracture resistance of the gear teeth.2 Analysis of gear pitting and dropout factors: pitting corrosion and dropout on the gear surface Read More
  • Total 517 pages  Go to Page
  • Go

WeiGao Transmission

Weigao Gear Reducer is an alliance group company that integrates research and development, production, sales, and service

+86 400 801 9158

Email: sales@wgt.net.cn;wgt.net.cn@gmail.com
Tel:+86571 85023000

WEIGAO REDUCER

FEEDBACK