WeiGao Transmission
Email: sales@wgt.net.cn
Language
通栏图2
tonglantu.jpg
Home / News

News Center

  • What are the factors that reducer oil temperature is too high?

    2022-12-20

    What are the factors that reducer oil temperature is too high?Factor analysis: a. Lubricating oil is unqualified or used for too long.At present, most of the lubricating oil used in our group's reducer is 320# extreme pressure gear oil. If you add expired or inconsistent oil with this type of lubricating oil and the lubricating oil has not been replaced for a long time, the oil temperature of the reducer may be too high; b. Too much lubricating oil.When the height of the oil level is higher than the oil dipstick or the upper and lower limits of the visible hole, the oil temperature of the reducer will be too high; c. The parts are damaged.Damage to mechanical parts includes severe pitting of gears, broken teeth, damage to bearing cages, inner and outer rings, balls, and bearing lockup or serious shaft deformation; d. The outside of the box is covered by debris or dust.When things are piled up around the reducer or the surface of the body has not been cleaned for a long time, the heat dissipation of the reducer may not be complete due to the coverage of debris or dust, resulting in an increase in oil temperature; e. The cooling device is blocked or fails.The cooling equipment is placed in the dusty workshop like the reducer Read More
  • What should I do if the bearing part of the reducer is overheated and noisy?

    2022-12-20

    What should I do if the bearing part of the reducer is overheated and noisy?a. Lack of lubricating oil.When the lubricated oil level is insufficient or cannot reach a reasonable height due to oil leakage from the reducer, it may cause high temperature or noise in the bearing part of the reducer; b. The bearing cover may have some conflicts in the seal.When the bearing is worn due to improper installation, irregular bearing cover or long-term use, the bearing cover or sealing part and the connecting part may cause high temperature or noise in the bearing of the reducer; c. Bearing damage or wear.The main content of this item is that the bearing cage is damaged, the inner and outer rings are worn or deformed, and the balls are worn or dropped out. These factors will make the reducer unable to work normally; d. The bearing gap is too large or too small.The above symptoms may occur when the gap between the ball and the inner and outer rings of the reducer bearing or the gap between the inner ring of the bearing and the shaft and the gap between the bearing and the end cover become larger due to long-term use; e. helical gear The key handle is loose.Looseness of the key handle of the helical gear will cause the gear Read More
  • What are the factors of gear pitting and shedding of reducer?

    2022-12-20

    What are the factors of gear pitting and shedding of reducer?Answer: A material, hardness, defect.The gear material does not meet the requirements; the primary factor affecting the contact fatigue strength of the gear is the low hardness after heat treatment, which cannot guarantee the proper Read More
  • How to use and maintain the reducer daily

    2022-12-20

    1 Equipment and adjustment In order to ensure the accuracy of the reducer (reduced motor) equipment, it is not necessary to start the equipment and not damage the sealant.You can open the oil inspection cover or use kerosene (diesel) to clean the anti-rust grease on the gear surface.b. Read More
  • Analysis of the factors of gear reducer shaft series and excessive oil temperature

    2022-12-20

    The reducer is connected in series with shaft a.It is because the input shaft loses its axial coupling due to broken teeth, resulting in shaft strings.b.The driven gear on the base shaft is not securely fastened to the shaft.In actual transmission, it is generally due to the interference between the driven gear and the base shaft Read More
  • Displacement principle of hard tooth surface reducer

    2022-12-28

    When hobbing with a rack-type pillar, when the reference line of the rack cutter is tangent to the pitch circle of the rack, the cut gear is a standard gear; when the reference line of the rack cutter is not in line with the pitch circle of the wheel blank When cutting, the cut out gear is modified Read More
  • Total 517 pages  Go to Page
  • Go

WeiGao Transmission

Weigao Gear Reducer is an alliance group company that integrates research and development, production, sales, and service

+86 400 801 9158

Email: sales@wgt.net.cn;wgt.net.cn@gmail.com
Tel:+86571 85023000

WEIGAO REDUCER

FEEDBACK