WeiGao Transmission
Email: sales@wgt.net.cn
Language
通栏图2
tonglantu.jpg
Home / News

News Center

  • Vibration measurement of gear reducer

    2023-04-27

    Choice of vibration measurement method There are two measurement methods for the vibration of the gear unit, one is to measure the vibration of the box and the other is to measure the vibration of the shaft.Combining these two measurement methods to obtain the absolute movement of the shaft in the gear unit is also a more effective method.For gear units supported by rolling bearings, the bearing radial clearance is small, and the relative movement between the bearing and the box is also small, so the box vibration measurement should be used.For gear units supported by ordinary sliding bearings, shaft vibration measurement or box vibration measurement can be used.However, when the frequency is in the range of 0-500Hz, the vibration measurement of the box is insensitive and difficult to measure the tiny vibration, so the shaft vibration measurement should be used.The vibration measurement of the box can obtain a wide frequency range and dynamic characteristics, which can provide the necessary basis for the analysis of the meshing frequency of the gear teeth.(2) Vibration measurement of the shaft The vibration displacement of the shaft should be measured relative to the box.Should use non-contact Read More
  • Method to relieve internal pressure of planetary reducer

    2023-04-27

    When the planetary reducer is running at high speed, the temperature and pressure changes in the inner cavity directly affect its load rate, continuous rotation speed and service life.In order to ensure that the input end and output shaft of the planetary reducer are sealed bearings and sealing rings, but the sealed bearings and sealing rings will also affect the temperature and pressure changes in the internal cavity of the reducer.Therefore, under the premise of considering the cost, it is necessary to consider that moderate is to reduce temperature and blood pressure.The temperature and pressure limit the maximum rotation efficiency of the planetary reducer to 98%, and 2% of the input energy is turned into heat and lost.This kind of damage mainly comes from the friction of the sealing ring and the bearing, which will increase the temperature of the inner cavity of the planetary reducer.Sometimes the relatively high natural ambient temperature outside will also increase the temperature of the internal cavity of the reducer.The temperature of the inner cavity of the reducer immediately limits the output torque and output speed ratio.There are many ways to reduce the pressure in the inner cavity of the planetary reducer: one is Read More
  • Analysis of the easy-to-produce faults of worm gear reducer

    2023-04-21

    As a traditional transmission system, the internal structure is a worm gear, and the tooth profile is involute.Many consumers of worm gear reducers have very limited understanding of worm gear reducers, not to mention the research on some existing problems. Next, the editor will work with you to understand the analysis of the existing problems of worm gear reducers.1. The reducer is hot and leaks oil.In order to better improve work efficiency, worm gear reducers usually use non-ferrous metals as the worm wheel, and the worm runs on harder materials.Because it is a sliding friction transmission, more heat will be generated during operation, which will cause differences in thermal expansion and contraction between the parts and seals of the reducer, and then gaps will be generated on each mating surface, and the lubricating oil will become thinner due to the increase in temperature. prone to leakage.There are four key factors that produce this situation, one is the unscientific matching of materials; the other is the poor quality of the meshing friction surface; the third is the incorrect choice of lubricating oil addition; Read More
  • Whether the reducer manufacturer is reliable or not, you will know by asking these five points clearly

    2023-04-21

    After years of testing, we have summarized some performance indicators to evaluate the quality of the reducer, especially the places that are prone to problems during the research and development process of the reducer.No one can escape these pits.Whether it can be solved and when it will be solved depends on the strength of research and development.Therefore, the next time a reducer manufacturer comes to your door, you can ask them if they have encountered these problems, and you will know whether this company is reliable or not.No matter what the reducer is, oil leakage is a problem that must be faced.The cause of oil leakage is more complicated, involving the brand of oil seal, oil seal assembly, shaft processing technology, use method, etc., and oil leakage can be divided into real oil leakage and fake oil leakage.The so-called false oil leakage refers to the oil leakage that occurs shortly after operation, the amount of oil leakage is not much, and it will not appear again after a short period of time.This is generally an internal pressure release, and once the pressure is released, everything will be fine.But the timing of the real oil spill is uncertain, it may be Read More
  • Why is the planetary reducer the most precise reducer?

    2023-04-21

    Acceptance criteria for gearboxes: Appearance inspection; no-load, temperature rise test; bearing clearance test; box vibration measurement test; shaft vibration displacement measurement test; installation and adjustment requirements; gearbox daily inspection and maintenance.1 Appearance inspection 1. Check by visual inspection. The appearance should be glossy, the paint should be evenly closed, whether the end cover, upper and lower covers and other studs are complete; whether there is a nameplate, and whether the content of the nameplate is clear and correct; 2. No gaskets are allowed to be filled, but sealant or water glass can be applied to ensure the sealing; 3. During assembly, before tightening the bolts of the box body, a 0.05mm feeler gauge should be used to check the sealing between the joint surface of the box cover and the box seat 4. The seal of the shaft extension should be coated with grease.The sealing devices of the reducer should be installed in strict accordance with the requirements.2 No-load and temperature rise test Add enough clean lubricating oil according to the specified oil quantity, and carry out forward and reverse no-load test runs at the rated speed.Trial run time Read More
  • How to choose a cost-effective hard tooth surface reducer

    2023-04-14

    Reducer With the rapid development of China's manufacturing industry, especially in the field of automation technology, the demand for reducers is increasing.But for the industry, ordinary reducers can no longer be achieved, and the emergence of hard tooth surface or helical gear reducers just fills this gap, so how to choose a cost-effective Read More
  • Total 517 pages  Go to Page
  • Go

WeiGao Transmission

Weigao Gear Reducer is an alliance group company that integrates research and development, production, sales, and service

+86 400 801 9158

Email: sales@wgt.net.cn;wgt.net.cn@gmail.com
Tel:+86571 85023000

WEIGAO REDUCER

FEEDBACK