The WXJ-18 worm gear reducer is WGT Weigao Transmission's worm-down mounting version of the WSJ / WXJ cylindrical worm reducer family. The "18" in the model number is the centre distance a expressed as one tenth of its real value, so the WXJ-18 is built around a 180 mm centre distance with the worm shaft running underneath the worm wheel, which leaves the space above the gearbox completely free for the driven machine. This arrangement answers one of the most common requests we receive from gearbox sizing and gear reducer selection work: how to fit a reduction stage into a vertical drive line where the output shaft must point down towards the machine floor, or where the input motor has to sit on top of the gearbox instead of beside it. Because a worm drive is a single-stage, high-ratio, self-locking mechanism, the same unit also covers service factor gearbox duties where the load must not back-drive, and the worm reducer ratio chart below shows the factory ratios available at this centre distance without any special order.
Every WXJ-18 is built as a single-stage Archimedean cylindrical worm drive with a keyed output shaft and a housing that accepts either the top-driven or the bottom-driven mounting form. The reducer is a mounting-form member of the WSJ / WXJ family, which WGT builds alongside its WD and WS cylindrical worm series; those series are produced to the PRC professional standard Q/ZB125-73 for single-stage Archimedean cylindrical worm reducers, and the same basic shaft-end geometry runs through the WD, WS, WD2 and WS2 variants. For technical buyers who need the gearbox maintenance angle covered as well, the thermal behaviour of the unit is not left to guesswork: the WXJ-18 has to pass a heat-emission check at an allowable oil temperature of 80 °C whenever the duty cycle exceeds 10 %.
| Item | Typical Range | Notes |
|---|---|---|
| Type | WXJ (worm below the worm wheel) | WSJ is the matching worm-up version; the two share dimensions per centre distance |
| Centre distance a | 180 mm | Coded as "18" in the model number (a / 10) |
| Factory ratios i | 12.33, 18.5, 37, 40, 51 | WSJ / WXJ ratios at 180 mm centre distance; at 120 mm the list is 9.67, 15, 20, 30, 40, 50 |
| Rated output torque | 544 N·m at i = 37, a = 180 | From the cylindrical worm reducer rated output torque table; non-standard ratios on request |
| Mounting form | I (output shaft up) or II (output shaft down) | Coded as the last field of the full designation, e.g. WXJ 18-37-II |
| Envelope A × A1 × B × B1 | 420 × 300 × 310 × 310 mm | Overall length and width dimensions, WXJ-18 outline |
| Overall height H | 540 mm | Frame height above the base |
| Shaft ends d / d1 | 60 mm / 45 mm | Shaft-end diameters on the type drawing; keyway widths b = 14 mm and b1 = 18 mm |
| Foundation fixing | 4 × d3 = 23 mm | Base bolt holes |
| Mass | 162 kg | WXJ-12 of the same family is 60 kg |
The values above are catalogue figures for the WXJ-18 outline and the factory ratio list; final centre distance, duty class and shaft extensions must be checked against the actual working conditions before an order is released.
| Ratio i | T2 (N·m) | Ratio i | T2 (N·m) |
|---|---|---|---|
| 9.67 | 602 | 27.5 | not offered |
| 11.67 | 624 | 30 | 646 |
| 13.67 | 592 | 33 | 572 |
| 15.67 | 566 | 37 | 544 |
| 17.67 | 480 | 41 | 594 |
| 19.5 | 528 | 47 | 565 |
| 21.5 | 532 | 53 | 480 |
| 23.5 | 566 | 60 | 516 |
| 25.5 | 542 |
Centre distance A = 180 mm, read from the catalogue rated output torque table of the cylindrical worm reducer family. A dash in the catalogue means the ratio has to be discussed with the factory. Efficiency at this size and ratio is below that of a helical stage, which is exactly why the selection method below works from the low-speed shaft torque rather than from input power alone.
A conveyor drive needs 2.2 kW from a 1450 r/min motor, and the belt pulley must run at about 39 r/min. The catalogue selection procedure starts from the original data — worm speed n1, the maximum working torque Mmax on the low-speed shaft, the required ratio i, whether the unit runs in one direction or both, and the duty cycle JC — and then works through five steps.
The full order designation is written as WXJ 18-37-II for the worm-down housing, 180 mm centre distance, ratio 37, mounting form II with the output shaft pointing down. For drives where the load must be held statically, the friction data in the same catalogue chapter is the deciding factor: the friction angle ρ of the worm mesh falls from 6°17'–6°51' at a sliding speed of 0.01 m/s to 0°48'–1°09' at 15 m/s, and a drive whose worm lead angle is smaller than the friction angle will stay self-locking, which is what makes this reducer acceptable on an overhead hoist.
Use the WGT Motor & Gearbox Online Selection System to confirm the centre distance, ratio, mounting form, shaft extensions and duty class for your WXJ-18 worm gear reducer, and to check the equivalent helical or helical-worm model when the drive calls for higher efficiency than a single-stage worm can deliver.