WeiGao Transmission
Email: sales@wgt.net.cn
Language
通栏图2
tonglantu.jpg
Home / Products / Coupling / WSS telescopic cardan shaft

Product Search

Products Category

loading

Share to:
facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

WSS telescopic cardan shaft

SKU:
Availability:
Quantity:

The WSS telescopic cardan shaft connects two shafts that cannot be perfectly aligned — and that still need to absorb axial movement — using cross-pin universal joints closed by a square-section sliding sleeve. The universal coupling body is offset in the middle, so the assembly shortens and lengthens as the running machine settles, expands under heat or vibrates, without manual re-alignment. WGT builds the WSS as a two-joint cross-pin unit with 45° of permitted rotation per section, H7 finished bores and a choice of needle-roller or plain sliding bearings — seven sizes from WSS2 to WSS8 covering 22.4 to 1120 N·m rated torque on bores from 12 to 42 mm. For heavy steel-mill and crane duty the SWC whole-fork cross-shaft series is the alternative, with 1.25 to 1000 kN·m and 15°–25° shaft-line angles.

Typical Specifications of the WSS Telescopic Cardan Shaft

Model Rated Torque (N·m) Bore d (mm) Outside D (mm) Lomin (mm) L (mm) L1 (mm) L2 (mm) Stroke S (mm)
WSS2 22.4 12 20 176 22 32 112 30
WSS3 45 14 25 200 27 40 120 30
WSS4 71 18 32 243 30 46 151 35
WSS5 140 22 40 287 38 58 171 43
WSS6 280 28 50 337 44 69 199 50
WSS7 560 35 60 428 60 91 246 65
WSS8 1120 42 75 556 84 122 322 90

Published WGT catalogue values. Lomin is the minimum overall length with the sleeve fully retracted; S is the axial stroke available as the sleeve moves; L, L1 and L2 are the end-section and sleeve lengths marked on the outline drawing.

Materials, Bearings and Construction

Item Specification Why It Matters
Bore tolerance Finished to H7 Interchangeable fit on standard shafting
Body material Quality 40Cr steel Shock and wear resistance in the cross-pin seats
Centre sliding block Hardened 45–50 HRC Keeps the sleeve true under reversing load
Cross pins Carburised and quenched 50–55 HRC Resists brinelling at the bearing seats
Bearing options Needle roller or plain sliding Needle roller to 4000 r/min; sliding type to 1000 r/min
Permitted rotation 45° per joint section Absorbs angular misalignment
Cross-pin architecture JB/T 5901 family WS/WSD and WSP in this range are published to JB/T 5901-1991, now JB/T 5901-2017

Where This Telescopic Cardan Shaft Is Used

  • Conveyors and material handling: belt and roller conveyors, screw conveyors and palletisers where drive and driven pulleys sit on separate foundations and the frame settles under load.
  • Textile, winding and printing machinery: spindles, winders and printing roller drives running at speed with a small, changing angular offset.
  • Packaging and automatic screw machines: cartoners, wrappers and multi-head drilling machines that reverse frequently, so the coupling absorbs repeated axial shock as well as misalignment.
  • Metallurgy, mining and chemical machinery: pumps, mixers, agitators and rolling-mill auxiliaries exposed to heat, dust and vibration, where a rigid flanged connection would over-stress the shaft bearings.
  • Farm, food and clean-down equipment: agricultural machinery, food-processing lines and cleaning equipment coping with corrosion, wash-down and daily temperature change.

Selection Example: 15 kW Conveyor Drive at 960 r/min

A belt conveyor needs 15 kW at 960 r/min, with roughly 25 mm of axial float between the drive and the driven shaft and about 2° of residual misalignment after the frame settles. The sizing chain runs as follows. First the theoretical torque from power and speed: T = 9550 × P / n = 9550 × 15 / 960 = 149.2 N·m. Apply a service factor of 1.5 for a conveyor with shock loading and frequent start-stop cycles, giving a required torque of 224 N·m. Read across the table above: WSS5 is rated at 140 N·m and is rejected, WSS6 at 280 N·m is accepted and still leaves a margin of 1.25×. The bore check comes next — the driven shaft is 25 mm, so WSS5 (d = 22 mm) would have failed on bore size too, while WSS6 at d = 28 mm fits. The speed check is where people get caught out: at 960 r/min the plain sliding-bearing version is technically inside its 1000 r/min ceiling but with no useful margin for pulley run-out, so the needle-roller type (rated to 4000 r/min) is specified. Finally the geometry: WSS6 has a minimum length Lomin of 337 mm and a stroke S of 50 mm, which covers the 25 mm of axial float in both directions and keeps the sleeve mid-travel rather than against an end stop. The selected item is a WSS6 telescopic cardan shaft with needle-roller bearings.

Your duty will differ — duty cycle, shock content and the amount of float to be absorbed all shift the optimum size. The same discipline applies when a cardan shaft feeds a gear reducer: treat torque, service factor and bearing speed as one calculation, and size coupling and gearbox in a single pass.

Get the Exact Model Online — Free Selection System

Open the WGT Motor & Gearbox Online Selection System, enter the power, running speed and the torque or stroke you need, and the system returns matching models with full technical data in seconds — no waiting for a quotation reply. It is the fastest way to confirm a cardan shaft or universal coupling size against the real duty, and to check a WSS against a SWC heavy-duty alternative when the torque envelope is larger. Send us a nameplate photo or type designation and our engineers will reply with a drop-in equivalent, price and lead time within 24 hours.

Previous: 
Next: 

WeiGao Transmission

Weigao Gear Reducer is an alliance group company that integrates research and development, production, sales, and service

+86 400 801 9158

Email: sales@wgt.net.cn;wgt.net.cn@gmail.com
Tel:+86571 85023000

WEIGAO REDUCER

FEEDBACK