WeiGao Transmission
Email: sales@wgt.net.cn
Language
通栏图2
tonglantu.jpg
Home / Products / Coupling / WS/WSD small universal joint (JB/T5901-1991)

Product Search

Products Category

loading

Share to:
facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

WS/WSD small universal joint (JB/T5901-1991)

SKU:
Availability:
Quantity:

The WS/WSD small universal joint is the light-duty end of the cross-pin family: a precision universal joint that passes torque between two shafts whose centre lines do not quite meet. WGT builds it in two forms — WSD as a single-joint unit, WS as a double-joint unit with a short intermediate shaft — so the same eight size steps can cover a small pump drive or a reciprocating machine. Every unit is finished to JB/T 5901-1991 for the cross-pin universal coupling series (now consolidated in JB/T 5901-2017), with an H7 finished bore, keyway, hexagonal or square bore options to suit the driven shaft. Rated torque runs from 11.2 to 1120 N·m across bores from 8 to 42 mm, each section articulates up to 45°, and the needle-roller build carries speeds to 4000 r/min where the plain sliding build stops at 1000 r/min.

Typical Specifications of the WS/WSD Small Universal Joint

Model Rated Torque (N·m) Bore d (mm) Outside D (mm) WSD-type Inertia, Y / J1 (kg·m²) WS-type Inertia, Y / J1 (kg·m²)
WSD1 11.2 8 or 9 16 0.06 / 0.05 –
WS1 11.2 10 16 – 0.08 / 0.07
WSD2 22.4 10 or 11 20 0.10 / 0.09 –
WS2 22.4 12 20 – 0.15 / 0.15
WSD3 45 12 25 0.17 / 0.15 –
WS3 45 14 25 – 0.24 / 0.22
WSD4 71 16 32 0.39 / 0.32 –
WS4 71 18 32 – 0.56 / 0.49
WSD5 140 10 or 20 40 0.72 / 0.59 –
WS5 140 22 40 – 1.04 / 0.91
WSD6 280 24 50 1.28 / 1.03 –
WS6 280 25 or 28 50 – 1.89 / 1.64
WSD7 560 30 60 2.82 / 2.31 –
WS7 560 32 or 35 60 – 3.90 / 3.38
WSD8 1120 38 or 40 75 5.03 / 4.41 –
WS8 1120 42 75 – 7.25 / 6.63

Published WGT catalogue values. Two build variants are listed for every size (Y-type and J1-type) and their inertias differ; the catalogue notes that published weights and inertias are approximate. Torque and bore combinations are confirmed against the actual duty before ordering.

WS or WSD, and How the Coupling Is Built

Item Specification Why It Matters
Type WSD Single cross-pin joint Compact and economical where the misalignment is small and the two shaft ends are coplanar
Type WS Double cross-pin joint with intermediate shaft Holds equal angular velocity when the two shafts are not in one plane
Permitted articulation Up to 45° per joint section The angle may be changed within its limits to suit the running machine
Permitted speed Needle-roller build to 4000 r/min; plain sliding build to 1000 r/min Needle rollers carry higher dynamic load with lower bearing clearance
Finished bore H7 Interchangeable fit on standard shafting
Bore forms Cylindrical, cylindrical with keyway, hexagonal, square Keyway and bore type and size to GB/T 3852-1997
Standard JB/T 5901-1991 series, consolidated in JB/T 5901-2017 Interchangeable with other JB/T 5901 cross-pin couplings

Where This Small Universal Joint Is Used

  • Woodworking machinery: saw spindles, planer and moulder drives where the cutter head sits slightly off the motor centre line.
  • Packaging and printing equipment: cartoners, wrappers, winders and printing roller drives running at speed with a changing angular offset.
  • Metallurgy and steel-mill auxiliaries: roller tables, manipulators and coil-handling auxiliaries exposed to shock, heat and dust.
  • Multi-head drilling, tapping and automatic screw machines: spindles that must index accurately while absorbing the offset of the feed rail.
  • Chemical, pharmaceutical and oil equipment: agitators, pumps and dosing units where corrosion-resistant finishes and clean-down routines matter more than peak torque.
  • Food, cleaning, textile and agricultural machinery: washing lines, winding frames, harvesters and material-handling equipment exposed to wash-down, dust and daily temperature change.

Selection Example: 7.5 kW Centrifugal Pump Drive at 960 r/min

A sludge pump takes 7.5 kW at 960 r/min, and the pump base settles enough to leave roughly 3° of permanent misalignment between the motor shaft and the pump shaft. The sizing chain runs as follows. First the theoretical torque from power and speed: T = 9550 × P / n = 9550 × 7.5 / 960 = 74.6 N·m. A centrifugal pump sits in the light-shock class of the coupling duty-factor table, so a factor of K = 1.3 is applied and the calculated torque becomes Tc = K × T = 1.3 × 74.6 = 97.0 N·m. Read across the table above: WS4 and WSD4 are rated at 71 N·m and are rejected, while WS5 and WSD5 at 140 N·m are accepted with a 1.44× margin. The bore check comes next — the pump shaft is 22 mm, so WS4 (d = 18 mm) would have failed on bore size as well as torque, and WS5 at d = 22 mm fits exactly. Next the angle check: when the shaft-line angle is not zero the coupling’s permitted torque is reduced to [T] = Tn · cosβ, so at 3° the WS5 still offers 140 × 0.999 = 139.8 N·m, comfortably above the 97.0 N·m required, and the angle is far inside the 45°-per-section limit. The speed check is where people get caught out: at 960 r/min the plain sliding-bearing version is technically inside its 1000 r/min ceiling but with no useful margin for pump run-out, so the needle-roller type (rated to 4000 r/min) is specified. Finally the type decision: because the misalignment is a fixed angle between two shafts that are not coplanar, the double-joint WS build is chosen, which keeps the driven shaft turning at a constant speed provided the intermediate shaft satisfies the equal-angular-velocity conditions — equal angles at both ends of the intermediate shaft, both end forks in the same phase, and the two centre lines in one plane. The selected item is a WS5 universal joint with a 22 mm H7 bore and needle-roller bearings.

Your duty will differ — shock content, speed and the amount of misalignment all shift the optimum size. The same discipline applies when a universal joint drives a gear reducer: treat torque, service factor and bearing speed as one calculation, and size the coupling and the gearbox in a single pass rather than guessing the shaft first.

Get the Exact Model Online — Free Selection System

Open the WGT Motor & Gearbox Online Selection System, enter the power, running speed and the torque or bore you need, and the system returns matching models with full technical data in seconds — no waiting for a quotation reply. It is the fastest way to confirm a universal joint size against the real duty, and to check a WS small coupling against a WSS telescopic cardan shaft or an SWC heavy-duty alternative when the torque envelope or the angular offset is larger than the small series can take. Send us a nameplate photo or a type designation and our engineers will reply with a drop-in equivalent, price and lead time within 24 hours.

Previous: 
Next: 

WeiGao Transmission

Weigao Gear Reducer is an alliance group company that integrates research and development, production, sales, and service

+86 400 801 9158

Email: sales@wgt.net.cn;wgt.net.cn@gmail.com
Tel:+86571 85023000

WEIGAO REDUCER

FEEDBACK