WeiGao Transmission
Email: sales@wgt.net.cn
Language
通栏图2
tonglantu.jpg
Home / Products / Coupling / G and GD precision universal joints

Product Search

Products Category

loading

Share to:
facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

G and GD precision universal joints

SKU:
Availability:
Quantity:

The G and GD precision universal joints from WGT are a machined, cross-pin (十字销) precision universal joint series built for continuous torque transmission between shafts that cannot be perfectly aligned. The G type is a single-cross Cardan joint; the GD type is a double-cross Cardan joint with an intermediate shaft between the two cross pins, so the same pair of shafts absorbs far more angular and parallel error. The range covers 15 size steps — 00G/00GD up to 13G/13GD — with catalogue rated torque from 5.3 N·m to 1990 N·m for the single-cross G and 4.1 N·m to 1563 N·m for the double-cross GD, and finished bores from 6 mm to 50 mm machined to H7. Needle-roller-bearing versions (GZ, GD2) are available up to nmax = 4000 r/min.

Typical Specifications of the G and GD Series

Item Typical Range Notes
Series and construction G single-cross, GD double-cross Cross-pin precision universal joints; both types share the same bore and body dimensions
Size range 00G/00GD to 13G/13GD (15 steps) Nominal torque 5.3-1990 N·m (G), 4.1-1563 N·m (GD)
Bore diameter d 6 - 50 mm H7 fit as standard; square (Q) and hexagon (SW) bores to H8
Body diameter D 12 - 93 mm Rises with size step, from 00G (Ø12 mm) to 13G (Ø93 mm)
Bearing versions Sliding bearing, needle roller bearing (GZ, GD2) Catalogue torques are for the sliding-bearing form; needle-roller versions carry half that torque
Maximum speed nmax = 4000 r/min (needle roller versions) Ask for the sliding-bearing speed rating when ordering a plain G/GD unit
Materials 40Cr, 40CrNi, 20CrMo, 20CrMnVB alloy steel Pins, bushings and yokes; SUS304 / SUS316 stainless steel optional; aluminium alloy or insulating nylon bushings optional
Bore options A, B, C, D A: plain bore with pin hole and clamp groove; B: keyed bore with tightening screw; C: square bore; D: hexagon bore

Values are typical catalogue figures. Torque, speed, bore and length must be recalculated against the actual duty — angle error, service factor, shock load and shaft condition — before a model is released.

Size and Torque Table

Size G Rated Torque G (N·m) Size GD Rated Torque GD (N·m) Bore d [H7] (mm) Body Ø D (mm) Key Width a [JS9] (mm) Square Bore Q [H8] (mm) Hex Bore SW [H8] (mm)
00G 5.3 00GD 4.1 6 12 - - -
01G 12 01GD 9.2 8 16 - 6 6
1G 26 1GD 24 10 20 3 10 10
02G 45 02GD 33 12 23 4 10 10
03G 71 03GD 49 14 25 5 12 12
04G 95 04GD 78 14 28 5 14 14
05G 132 05GD 98 16 32 5 16 16
06G 175 06GD 130 18 36 6 18 18
07G 252 07GD 189 20 42 6 20 20
08G 332 08GD 249 22 45 6 22 22
09G 495 09GD 363 25 50 8 25 25
10G 795 10GD 595 30 58 8 30 30
11G 1200 11GD 900 35 68 10 - -
12G 1650 12GD 1386 40 78 12 - -
13G 1990 13GD 1563 50 93 14 - -

Torque figures are catalogue nominal values for the sliding-bearing form. Needle-roller versions (GZ, GD2) transmit half these values; key width a [JS9] is the standard key size of the B-type keyed bore.

Dimensions of G and GD Precision Universal Joints

Size C (mm) L1 (mm) L2 (mm) G Overall L4 (mm) GD Cross-Pin Pitch L3 (mm) GD Overall Clamp Groove H (mm)
00G / 00GD 9 15.5 31 - - 4.5
01G / 01GD 9 18 36 22 58 5
1G / 1GD 10 21 42 26 68 5
02G / 02GD 14 26 52 31 86 7.5
03G / 03GD 16 29.5 59 35 94 8.5
04G / 04GD 15 30 60 41 101 7.5
05G / 05GD 23 41 82 43 125 11
06G / 06GD 25 43.5 87 45 132 12
07G / 07GD 25 47 94 55 149 12
08G / 08GD 22 47.5 95 55 150 11
09G / 09GD 26 54 108 65 173 13
10G / 10GD 29 61 122 78 200 14.5
11G / 11GD 35 70 140 86 226 17.5
12G / 12GD 40 80 160 104 264 20
13G / 13GD 50 95 190 114 304 25

L1 is the half length of the G from each bore shoulder to the cross pin and L2 the G overall length. On the GD, L4 is the distance between the two cross pins and L3 the overall length including the intermediate shaft. Clamp groove H applies to the A-type bore. Values are catalogue dimensions for the standard range.

Where This Precision Universal Joint Is Used

  • Packaging machinery and carton conveying lines, where driven rollers run slightly out of line with the drive shaft
  • Printing machinery and paper-making machines with driven rolls on common shafts
  • Textile machines, winding equipment and spinning frames
  • Woodworking machinery, multi-head drilling and tapping machines
  • Metallurgical, chemical and petroleum machinery, including pumps and process skids
  • Agricultural machinery, forestry equipment and irrigation pump drives
  • Automatic welding machinery and motion-simulation rigs
  • Special vehicles, industrial buses and machine-tool auxiliary drives
  • Medical and cleaning equipment where stainless or insulating nylon versions are specified

A universal coupling is specified when the drive cannot be made coaxial. Three errors must be absorbed: axial error (movement between the two shafts, usually caused by motor vibration), parallel error (the offset between driving and driven shaft) and angle error (the angle formed by the two intersecting axes). The single-cross G handles small angles with the correct fork orientation; the double-cross GD adds an intermediate shaft so a larger combined angle and offset can be taken up. For constant speed the two shafts must be aligned parallel, and when a double joint is built from two single joints the fork direction has to follow the catalogue arrangement.

Selection Example: 2.2 kW Packaging Line Roller at 1,450 r/min

A packaging machine drives a carton roller from a 2.2 kW, 1,450 r/min motor. The roller shaft is offset and misaligned by 6°, so a universal joint sits between motor and roller.

Step 1 — Working torque. T = 9550 × P / n = 9550 × 2.2 / 1450 = 14.5 N·m

Step 2 — Service factor. Packaging machinery is a light-impact duty, so condition coefficient K = 1.3 applies: design torque = 14.5 × 1.3 = 18.8 N·m

Step 3 — Angle correction. Torque capacity falls with angle error, so divide the catalogue torque by cos β: 18.8 / cos 6° = 18.8 / 0.9945 = 18.9 N·m

Step 4 — Size selection. 01G gives only 12 N·m — not enough. 1G gives 26 N·m, comfortably above 18.9 N·m. If the offset needs more compensation, the double-cross 1GD gives 24 N·m, also above 18.9 N·m, so the GD type is possible on the same size step.

Step 5 — Bore check. The motor shaft is 10 mm, matching the 10 mm H7 bore of the 1G / 1GD. With the B-type keyed bore, key width a = 3 mm (JS9) and the catalogue keyed-bore dimension is b = 11.4 mm.

Step 6 — Speed and bearing version. 1,450 r/min is far below the 4,000 r/min needle-roller limit, so the needle version GZ is possible — but its torque is only half the sliding value, 26 / 2 = 13 N·m, below 18.9 N·m. Step up one size to 02G(Z) at 45 / 2 = 22.5 N·m, which passes.

Step 7 — Order code. The line is written as model, bore type, bore diameter, bore type, bore diameter: for example 1G A(B,C,D) 10 A(B,C,D) 10, with (Z) added after the size for the needle-roller version. Standard stock 1W-03G sizes use the A-type bore and 04G-13G the B-type bore; internal spline, spline shaft, keyed plain shaft, square shaft, hexagon shaft and small flange ends are available on request.

Get the Exact Model Online — Free Selection System

Match motor power, speed, bore and misalignment against the full G and GD table in the WGT Motor & Gearbox Online Selection System — the fastest route through universal joint selection — and confirm size, bore form and bearing version before ordering. For sizes outside the standard range, or a stainless steel, aluminium alloy or insulating nylon build for a special environment, send the duty data and our engineers will confirm the configuration. For installation and universal joint maintenance, grease the pin bushings at the maker's interval and re-check the bore fit and clamp screws at every shutdown.

Previous: 
Next: 

WeiGao Transmission

Weigao Gear Reducer is an alliance group company that integrates research and development, production, sales, and service

+86 400 801 9158

Email: sales@wgt.net.cn;wgt.net.cn@gmail.com
Tel:+86571 85023000

WEIGAO REDUCER

FEEDBACK