WeiGao Transmission
Email: sales@wgt.net.cn
Language
通栏图2
tonglantu.jpg
Home / Products / Coupling / CSCA/CSCW universal joint

Product Search

Products Category

loading

Share to:
facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

CSCA/CSCW universal joint

SKU:
Availability:
Quantity:

The CSCA/CSCW universal joint is the FA factory-automation standard cross coupling for drives where two shafts cannot be made perfectly parallel — packaging machinery, multi-spindle drills, printing presses, winding machines and woodworking equipment. CSCA is the single fixed-pin type: one cross, one bearing set, compact and light. CSCW is the double fixed-pin type: two crosses back to back, so it absorbs angular misalignment and parallel offset together. WGT builds both in 42CrMo alloy steel, with 304 stainless steel for wash-down and hygienic duty, over a 6–30 mm bore range.

Typical Specifications of the CSCA/CSCW Universal Joint

Bore d (mm) Outside D (mm) Length L / LD (mm) Allowable Torque (N·m) Allowable Speed (r/min) Static Break Torque (N·m) Mass (g)
6 12 31 / – – 1800 16 15
8 15 36 / – – 1500 35 30
10 20 42 / 67.5 20.1 1300 83 55
12 23 52 / 83 33 1100 140 110
14 25 59 / 94.5 46 1000 200 155
16 32 74 / 117.5 76 900 310 260
18 32 81 / – – 800 400 345
20 36 87 / 139 129 700 530 465
25 45 105 / – – 600 1000 790
30 50 122 / – – 550 1500 1160

Table shows WGT catalogue values for the standard CSCA (single, L) and CSCW (double, LD) series. A dash means WGT does not publish that value for that combination: allowable torque is published for the single type from d = 10 to 20 mm, and the double type is catalogued in d = 10, 12, 14, 16 and 20 mm. CSC / CSW rubber-bushed versions cover the same bore range. These are typical ranges for the catalogue build — every order is re-checked against your actual speed, angle, torque and cycle count before release.

This precision FA family is one of three universal-joint families in the WGT range. Heavy cross-pin couplings built to JB/T 5901 — the WX/WXD small cross-axis type and the WS/WSD small universal joint, covering 11.2–1120 N·m with up to 45° per joint — and the SWC cardan shaft series are specified on shaft torque and angle instead. Above roughly 1800 r/min, or a few hundred N·m, ask for the JB/T 5901 cross-pin types or an SWC telescopic cardan shaft instead.

Where This Universal Joint Is Used

  • Packaging machines: carton erectors, wrappers and case packers, where cam and crank shafts are never perfectly aligned and the drive reverses constantly.
  • Multi-spindle drills and woodworking machinery: spindles set at an angle to the drive motor; the CSCW double type keeps both spindles in phase.
  • Printing and web-handling equipment: registration rolls and tension rollers that must tolerate a small permanent offset as the web runs.
  • Textile, winding and spinning machinery: high cyclic content with frequent direction reversal — the fixed-pin, built-in bearing design responds equally fast clockwise and anticlockwise.
  • Food, chemical and pharmaceutical machinery: the 304 stainless steel build and CSC / CSW rubber-bushed options for wash-down and hygienic environments.
  • Metallurgy, pumps and general industrial drives: where angular and parallel error comes from frame and foundation movement, not poor assembly.

Selection Example: 0.75 kW Carton Erector Cam Drive

A packaging machine drives a cam crank from a 0.75 kW, 960 r/min motor through a cross coupling. The crank shaft sits 6° out of line with the motor shaft and 12 mm off-axis, and the cam reverses every 1.5 seconds.

1. Design torque. T = 9550 × P / n = 9550 × 0.75 / 960 = 7.46 N·m at the joint. The reversing cam duty carries a service factor of 2.0, so Tdesign = 14.9 N·m.

2. Condition variable. WGT’s selection method combines speed, angle and torque into one check: condition variable = speed (r/min) × angle (°) × torque (N·m), which must stay below the allowable condition variable published for the size. Here 960 × 6 × 14.9 = 85,800. At d = 10 mm the allowable condition variable is 70,000 — rejected; at d = 12 mm it is 106,000 — accepted.

3. Speed with angle coefficient. Permissible speed is derated by the misalignment angle: 1.00 below 5°, 1.05 at 10°, 1.18 at 15°, 1.43 at 20°, 1.82 at 25°, 2.50 at 30°. With 6° of misalignment the next step up, 1.05, applies: 960 × 1.05 = 1008 r/min against an allowable 1100 r/min at d = 12 mm — inside the limit.

4. Torque and static margin. Allowable torque at d = 12 mm is 33 N·m against the 14.9 N·m design torque, a margin of 2.2×. The static break torque of 140 N·m is 9.4× the design load, so a jam shears the joint before it damages the cam.

5. Structure, and pairing with the reducer. The 12 mm parallel offset cannot be absorbed by a single joint, so the double type is required: CSCW, d = 12 mm, LD = 83 mm, A = 31 mm, 180 g, Gd² = 0.55 kg·cm², static break torque 100 N·m. Because the coupling sits on the gear reducer output shaft, the same service factor of 2.0 is carried into the gearbox sizing, and the reducer’s low-speed shaft bore and key must match the d = 12 mm H7 finished bore.

That is one complete universal joint selection in five steps. Your duty point will differ — speed, misalignment angle, offset, duty cycle and environment all shift the answer, which is why universal coupling sizing is done against the real machine rather than from a catalogue cover.

Get the Exact Model Online — Free Selection System

Open the WGT Motor & Gearbox Online Selection System, enter your power, input speed and required output speed or torque, and the system returns matching models with full technical data in seconds. Need a cross-reference against an imported WS, WSD, SWC or a Japanese FA-standard joint? Send the type designation or a nameplate photo and our engineers will reply with the equivalent, price and lead time within 24 hours. 304 stainless steel, special bores, keyways, telescopic extensions and universal joint maintenance spares are available on request.

Previous: 
Next: 

WeiGao Transmission

Weigao Gear Reducer is an alliance group company that integrates research and development, production, sales, and service

+86 400 801 9158

Email: sales@wgt.net.cn;wgt.net.cn@gmail.com
Tel:+86571 85023000

WEIGAO REDUCER

FEEDBACK