Article List
- How to maintain the gear of the reducer1. Start the main motor and grind in the forward and reverse directions.During the grinding process, since the wear of the abrasive is quite fast, it is necessary to apply the abrasive to the gear from time to time to observe the change of the tooth surface.When the meshing contact area is t
- How to maintain the gear of reducer1. Start the main motor and grind in the forward and reverse directions. During the grinding process, because the abrasion of the abrasive is quite fast, it is necessary to coat the abrasive on the gear from time to time and observe the change of the tooth surface. When the meshing contact area of t
- What are the reasons for the burnout of the geared motor?What are the reasons for the motor burnout of the spiral reducer?The editor will introduce you one by one: 1.The compressor starts up frequently.During the starting process of the motor, although it is started by reducing vo, the starting current is still several times the rated current.
- What are the reasons for the burning of the reducer motor?What are the reasons for the burning of the motor of the helical reducer? A small editor will introduce you one by one:1. The compressor starts frequently. In the process of starting the motor, the starting current is still several times of the rated current although it is started by reducing the vo
- How to prevent the reducer from rustingSince the reducer is mostly made of steel, if the machine is not maintained during use, it will be easily oxidized and rusted after a long time of use, which will greatly reduce its service life.To this end, we can take the following measures to prevent rust.1.reduced rust
- How to prevent the reducer from rustingAs the reducer is mostly made of steel, if you do not pay attention to maintenance during use, the machine is easy to be oxidized and rusted after a long time of use, which will greatly reduce its service life. To this end, we can take the following measures to prevent rust.1. The rust of the reduce
- How to deal with gear reducer crevice corrosion?It is caused by overload. The partial overload of the gear makes the specific contact stress greatly exceed the allowable contact stress of the gear raw material. Some gears cannot reach the full tooth length contact, or only touch on one side of the tooth, or even corner contact. Let's elaborate in
- How to deal with crevice corrosion of gear reducer?It is caused by overload.The local overload of the gear makes the specific contact stress greatly exceed the allowable contact stress of the gear raw material.Some gears cannot reach full tooth length contact, or only contact one side of the tooth, or even angular contact.let's elaborate
- How to choose a high-power reducer?The case of using a high-power servo is applied to high-torque and high-precision occasions.Therefore, the following suggestions are given: 1. 2——4.5kw with a reduction ratio of less than 20:1 is matched with a precision planetary reducer. The power in this range is the most cost-effective with a planetary reducer. It has stable performance in all aspects, good precision, long life, and maintenance-free. .2. If the reduction ratio of 5-7.5kw is less than 7:1, it can also be equipped with a planetary reducer, but the price of the planetary reducer at this time is not cheap.3. For 7.5-11kw reducers, be careful when using the planetary reducer at this time. First, pay attention to the load impact not being too large. At this time, the planetary reducer is prone to chipping and wears quickly under the condition of high torque. , noisy, and the price is quite expensive.At this time, you can consider using a roller reducer. Its accuracy is even better than that of the planetary reducer, and its rated torque is higher than that of the planetary reducer.
- How to check the oil condition of the reducer correctly?Anyone who uses the reducer knows that the reducer is in use and needs to be lubricated with lubricating oil.In the case of deceleration and use, we must regularly check the deceleration of the oil so that it can be added in time to ensure that the service life of the reducer during use is also guaranteed to be error-free.So, let us introduce the oil inspection steps of the reducer: 1. Turn off the power to prevent electric shock and wait for the reducer to cool down.2. Check the viscosity index of the oil.3. Check the oil level and pass the test.4. If the oil is obviously turbid, it is recommended to replace it as soon as possible.5. Open the oil drain plug and take out the oil sample.6. Suitable for reducer with oil level plug.7. Install the oil level plug.The above steps are essential for the oil inspection of the reducer.