What are the common misunderstandings in B series gearbox maintenance?

Publish Time: 2026-11-20     Origin: Site

1. Misunderstandings in lubrication management

1. Only add new oil and do not clean the old oil

Many maintenance personnel directly add new oil when they find that the oil level is low, or simply drain it when changing the oil. After long-term operation of the gearbox, metal wear debris and sludge will be generated inside. If the cavity is not cleaned, the remaining impurities will continue to rub along with the gear mesh, accelerating the wear of precision transmission components.

2. Wrong and random mixing of oil products

Failure to strictly follow the equipment instructions to select industrial gear oil of specified grade and viscosity (such as N110-N200 medium extreme pressure gear oil). Different brands and models of lubricants have different additives. Mixing them will change the viscosity of the oil, destroy the stability of the oil film, and cause abnormal noise and vibration.

3. Inaccurate oil quantity control

It is a common mistake to think that "the more oil, the better". Overfilling will cause the internal pressure of the gearbox to rise, causing severe heating and oil leakage; insufficient oil will cause local dry friction, leading to dry grinding of gears and damage to bearings.

2. Misunderstandings about operation and working conditions

1. Ignore the running-in and observation in the early stage of operation

If a new reducer or equipment after overhaul is put into operation in the initial stage (about 300 hours), if it is directly operated at full load and at high speed, it will cause hidden damage to the internal parts. The correct approach is to appropriately reduce the load and closely observe the temperature rise and noise. The first oil change must be performed after this stage.

2. Blindly increase the power of the equipment or overload operation

Running the gearbox beyond the load limit specified on the nameplate for a long time, or frequently subjected to huge impact loads, will greatly shorten the life of the equipment, and even lead to serious failures such as overheating and burning of the motor coils and broken gear teeth.

3. Misunderstanding "maintenance-free" as "no maintenance"

Some modern gearboxes are designed to last a long time, but they are not maintenance-free. Failure to perform regular oil level checks, seal condition assessments, and connecting fastener rechecks after installation will still lead to premature equipment failure.

3. Misunderstandings in installation and assembly

1. Poor installation alignment and insufficient base rigidity

The installation between the reducer, motor and working machine is crucial to neutrality. Small misalignments will be amplified in long-term operation, resulting in additional bending moments and radial forces, causing severe vibration, noise and bearing damage.

2. Violent percussion assembly

When replacing gears or bearings, directly hitting the parts with a hammer will cause hidden damage to the parts. There may be no obvious failure in the short term, but the wear will be accelerated in the later period.

3. Neglect the maintenance of vent plugs and seals

If the vent plug is blocked, the pressure inside the box cannot be released normally, and the sealing structure will continue to be squeezed, causing the seals to age and fail, forming a vicious cycle of oil leakage. In addition, if the sealing ring is damaged and not replaced in time, the precision parts will become oxidized due to moisture.

4. Misunderstandings in troubleshooting

1. Continue to run forcefully after abnormal noise occurs.

When abnormal knocking sounds or sharp noises occur in the equipment, choosing to "persevere despite illness" due to tight production tasks will lead to the rapid expansion of the scope of the fault and turn small problems into major repairs.

2. Passively wait for a fault to occur

Lack of regular temperature, vibration and noise inspection system. Temperature is usually the first indicator of gearbox failure. If the temperature rises rapidly and becomes unstable, the machine must be shut down immediately for troubleshooting rather than waiting for the equipment to completely fail.

Avoiding these maintenance misunderstandings and establishing a scientific lubrication and condition monitoring system can not only effectively reduce the equipment failure rate, but also significantly extend the service life of the B series gearbox.

FEEDBACK

Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand

How to check the carrying capacity of worm gear reducer: working condition coefficient, efficiency and Selection calculation example - Hangzhou Weigao Transmission

Lubrication and maintenance characteristics of B series industrial gearboxes

What are the common misunderstandings in B series gearbox maintenance?

Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor