How to check the carrying capacity of worm gear reducer: working condition coefficient, efficiency and Selection calculation example - Hangzhou Weigao Transmission
Publish Time: 2026-11-20 Origin: Site
What should be checked for the load-bearing capacity of worm gear reducer?
When selecting a worm gear reducer, most of the manufacturers will provide you with an "input shaft power - output shaft torque" comparison table. Getting the table does not mean that the calibration has been completed: the values in the table are the allowable values calculated under ideal working conditions of continuous operation for 8 hours a day and stable load. Whether it can be installed on-site or not due to overheating and wear depends on whether the working condition coefficient, meshing efficiency, and input shaft speed have been clearly calculated.
On December 3, 2025, GB/Z 115-2025 "Calculation of the Loading Capacity of Gear and Worm Pairs" was released and implemented. It is currently effective and is equivalent to ISO/TS 14521:2020, which fixes the load-carrying capacity evaluation method of cylindrical worm pairs.
project |
content |
Standard number and name |
GB/Z 115-2025 "Calculation of Bearing Capacity of Gear and Worm Pairs" |
Release and Implementation |
Released and implemented on 2025-12-03, current |
Procurement status |
Equivalent to ISO/TS 14521:2020 |
Cover failure modes |
Tooth surface wear, tooth surface pitting, worm deformation, gear tooth fracture, temperature load rating |
Not covered |
Gluing and other failure modes |
applicable boundary |
Sliding speed vg ≤ 25 m/s, coincidence degree ε > 2.1 |
Applicable range of center distance |
a ≥ 50 mm, select size, lubricant and material according to standard; a < 50 mm, use method A |
The key point is that "the sample gives the allowable value and the standard gives the verification method". The sample rated value has been converted into a value that can be directly checked. There are three steps to be completed on site: correcting the working conditions, calculating the efficiency, stuck speed and temperature rise.
How does the efficiency in the standard method come from?
The efficiency expression of ISO/TS 14521 is written as η = (cos αn − µ·tanγ) ÷ (cos αn + µ/tanγ), αn is the normal pressure angle (20° for the standard worm), µ is the meshing friction coefficient, and γ is the worm lead angle; the lead angle is determined by γ = arctan(z₁·m/d₁), z₁ is the number of worm heads, m is the module, d₁ is the diameter of the worm pitch circle. The decisive factor of efficiency is firstly the speed ratio: the larger the speed ratio, the smaller the lead angle of the single-head worm, and the lower the efficiency; the second is the sliding speed.
Step 1 and 2: Conversion of operating condition coefficient K and efficiency
Working condition coefficient K: magnify ideal working conditions to the scene
In actual use, repeated starts and stops, forward and reverse rotation, impact loads, and operation time deviations from 8 hours will all make the demand higher than the allowable value. The sample is uniformly amplified by the working condition coefficient K.
Load conditionDaily operating time (hours) |
0.5~2 |
2~6 |
6~10 |
10~24 |
steady load |
0.80 |
0.90 |
1.00 |
1.25 |
medium impact |
0.90 |
1.00 |
1.25 |
1.50 |
Big impact |
1.00 |
1.25 |
1.50 |
1.75 |
Note: When the number of forward and reverse rotations or stops and starts reaches more than 10 times in one hour, the K value in the above table should be multiplied by 1.2.
Efficiency: Torque and power cannot be directly converted
The conversion formula given in the sample is: input power P (kW) = output torque T (N·m) × output shaft speed N₂(r/min) ÷ (9549 × efficiency η); output shaft speed N₂ = N₁ ÷ transmission ratio i.
Transmission ratio |
1/10 |
1/15 |
1/20 |
1/25 |
1/30 |
1/40 |
1/50 |
1/60 |
efficiency range |
77-90% |
76-88% |
75-84% |
72-82% |
68-82% |
64-75% |
62-72% |
60-71% |
Efficiency also varies with input speed. Sample reminder: When the reducer is driven by pulleys, sprockets and couplings, the input shaft speed should not exceed 2000 r/min. The general speed range is 600~1800 r/min. Excessive speed can easily increase bearing friction and shorten service life.
Step 3: Complete calculation example, a 600 kg lifting mechanism
The following is recalculated based on the original calculation example printed on pages 31 to 32 of the Hangzhou Weigao Transmission WP Worm Gear Reducer Selection manual, and cross-checked with the load-carrying capacity table printed on page 33.
Known conditions
project |
numerical value |
Lifting object weight W |
600kg |
Lifting speed V |
12 m/min |
Roller diameter D |
0.4 m |
Pulley transmission efficiency η₁ |
0.92 |
Reducer transmission efficiency η₂ |
0.71 |
Running time |
8 hours/day |
Number of starts |
2 times/hour, big impact |
power supply |
Three-phase 380 V, 50 Hz, 1440 r/min |
Calculation process
Step 1: Pulley speed and overall transmission ratio. Pulley speed N₁ = V ÷ (D × 3.142) = 12 ÷ (0.4 × 3.142) = 9.55 r/min, the sample is 9.6; the total transmission ratio i = 1440 ÷ 9.6 = 150; set the belt transmission ratio i₁ = 5, then the reducer transmission ratio i₂ = 150 ÷ 5 = 30.
Step 2: The reducer outputs torque. T = W × 10 × (D/2) ÷ (i₁ × η₁) = 600 × 10 × 0.2 ÷ (5 × 0.92) = 260.87 N·m.
Step three: Correction of working condition coefficient. 8 hours/day in the range of 6~10, large impact, check the K value table and find K = 1.25, corrected output torque T₂ = T × K = 260.87 × 1.25 = 326.09 N·m.
Step 4: Convert input power. Output shaft speed N₂ = 1440 ÷ 30 = 48 r/min, P = T₂ × N₂ ÷ (9549 × η₂) = 326.09 × 48 ÷ (9549 × 0.71) = 2.31 kW.
Step five, look up the table Selection. In the load capacity table printed on page 33, the rated input power of model 120 (center distance 120 mm) and transmission ratio 1/30 is 3 kW, and the rated output torque is 413 N·m. Power margin = 3 ÷ 2.31 = 1.30, about 30%; torque margin = 413 ÷ 326.09 = 1.27, about 27%.
There is one detail worth noting. The text of step 3 on page 32 of the printed manual says "working condition coefficient K = 1.5", but the calculation example on the same line uses T₂ = 260.9 × 1.25 = 326 N·m, which is consistent with the 1.25 corresponding to 6~10 hours and larger impact in the K value table. Both values do not affect the final model: if recalculated according to 1.5, T₂ = 391.30 N·m, P = 2.77 kW, still within 3 kW, but the power margin drops from 30% to 8%, and the motor has almost no margin. When copying calculation examples, the K value table and calculation formula shall prevail.
Step 6: Back-calculate the efficiency from the rated value for cross-checking. η = T₂ × N₂ ÷ (9549 × P₁): The input speed is 1500 r/min according to the calibrated load capacity table, N₂ = 50 r/min, η = 413 × 50 ÷ (9549 × 3) = 72.1%; the input speed is 1440 r/min according to the calculation example, N₂ = 48 r/min, η = 413 × 48 ÷ (9549 × 3) = 69.2%. Both fall within the efficiency range of 68-82% of the sample transmission ratio of 1/30, indicating that the calculation example η₂ = 0.71 is a conservative value. When the input speed is increased from 1440 r/min to 1500 r/min, the back-calculated efficiency increases by about 3 percentage points, which is consistent with the sample"s explanation that efficiency increases with speed.
After checking the form, there are three more checks
Input shaft speed and output speed
The 1440 r/min in the calculation example falls within the range of 600~1800 r/min, and there is still room for the upper limit of 2000 r/min. However, when using a frequency converter to adjust the speed, it must be recalculated: N₂ = N₁ ÷ i changes, and the efficiency, heat generation and load rating all change accordingly.
Lubrication and oil temperature
Sample regulations: When the ambient temperature is -30 ℃ ~ 40 ℃, inject N220~N320 lubricating oil, and when the ambient temperature is -30 ℃ ~ 65 ℃, use N320~N460, fill it to the center point of the oil mark and remove the breather taper plug; clean the inside and replace it with new oil after the first 100 hours of use, and change the oil every 2500 hours thereafter. The maximum allowable oil temperature during operation is 95°C, and it can continue to be used if it does not rise again.
Fault phenomenon |
Possible reasons |
Treatment method |
overheat |
overload |
Appropriately reduce the load |
overheat |
Oil seal excessive friction |
Lubricant dripping from oil seal lip |
overheat |
Too much or too little oil |
Adjust the oil volume according to the red dot on the oil mark |
overheat |
Lubricating oil contains many impurities |
Replace with suitable new oil |
vibration |
Improper connection between the three |
Adjust the position to make the axis coaxial |
vibration |
Worm gear tooth wear |
Replace worm gear pair |
vibration |
Bearing wear or excessive clearance |
Replace bearings |
vibration |
Bolts loose |
Reinforcement bolts |
Installation and alignment
The sample requires that the reducer be installed on a flat and solid base, and the foot bolts are tightened to prevent shock; the joints of the power equipment, reducer, and working machine are adjusted to make the three axes coaxial after installation. The input end shaft extension outer diameter tolerance is made according to J6, and the output end is made according to JS6. The inner holes of the coupling, pulley, and sprocket of the shaft must be prepared according to appropriate tolerances to avoid excessive tightness that damages the bearings and excessive looseness that affects power transmission. Transmission parts such as sprockets and gears should be installed close to the bearings.
in conclusion
The load capacity check of the worm gear reducer can be divided into three steps: first use the working condition coefficient K to enlarge the ideal working condition to the site, then use the conversion formula with efficiency to convert the torque into power, and finally use the load capacity table to determine the model and leave a margin. GB/Z 115-2025 has fixed the standard method, and the sample ratings can be used directly. Four items, including working condition coefficient, efficiency value, upper limit of speed and upper limit of oil temperature, still have to be added on site. The same set of ideas also applies to cycloidal pinwheel reducers and hard tooth surface reducers; gear reduction motors also need to consider the overall thermal balance of the motor and reducer.
Self-inspection sequence: Take K according to the stricter load conditions and longer operating time, do a conservative conversion according to the lower limit of the speed ratio efficiency range, and then check whether the input speed exceeds the limit and whether the rated power has margin. After the four steps, the model will be determined. Hangzhou Weigao Transmission"s worm gears, cycloid pinwheels and hard tooth surface product lines all provide Selection data and load capacity tables according to this method.