How to determine the two-stage speed ratio of the cycloidal pinwheel reducer: how to read the combination table, how to check it, and how to find the frame number - Hangzhou Weigao Transmission
Publish Time: 2026-11-19 Origin: Site
How to determine the two-stage speed ratio of the cycloidal pinwheel reducer: how to read the combination table, how to check it, and how to find the frame number
One of the most easily overlooked things about the cycloidal pinwheel reducer is that the speed ratio is not a continuous number that can be obtained by multiplying it casually. The first-stage speed ratio is determined by the number of teeth and only falls on a fixed gear; the two-stage speed ratio is a combination of two multiplied stages and falls on a discrete grid formed by these gears. The combination table only answers "what are the options", but there are still three steps left to "which group and which frame number to choose": understand the meaning of the combination, check the table itself, and use the load-carrying capacity table to determine the power and torque to the frame number. The following is a walkthrough of Hangzhou Weigao Transmission 8000 series samples.
1. The single-stage speed ratio is the number of teeth, and the two-stage speed ratio is the combination.
1.1 First gear ratio: only 17 gears
The cycloid pinwheel planetary transmission is a transmission with one tooth difference and less tooth difference. The number of pin teeth is one tooth more than the number of cycloidal wheel teeth. The single-stage speed ratio value is the same as the number of cycloidal wheel teeth. The single-stage optional speed ratios in the sample are 7, 9, 11, 13, 15, 17, 21, 23, 25, 29, 35, 43, 47, 51, 59, 71, and 87, a total of 17 gears. The characteristics page states that the single-stage 1/7~1/87 is not available for single-stage speed ratios other than the gears. Terminology and geometric element codes are in accordance with GB/T 10107.1-2012, GB/T 10107.2-2012, and GB/T 10107.3-2012.
1.2 Two-stage speed ratio: 32 combinations, falling on a discrete grid
The two-stage speed ratio is obtained by multiplying two single-stage gears. There are 32 two-stage combinations in sample table 8-3 (printed page 567), with the total speed ratio ranging from 99 to 7569. The following table excerpts 15 groups. Each cell indicates "total speed ratio (multiplication of two first-level speed ratios)", which is consistent with the sample.
Overall speed ratio |
Combination (two first-stage ratios) |
Overall speed ratio |
Combination (two first-stage ratios) |
Overall speed ratio |
Combination (two first-stage ratios) |
|---|---|---|---|---|---|
99 |
9×11 |
187 |
17×11 |
437 |
43×11 |
121 |
11×11 |
289 |
17×17 |
559 |
43×13 |
143 |
13×11 |
377 |
29×13 |
595 |
35×17 |
165 |
15×11 |
649 |
59×11 |
731 |
43×17 |
195 |
15×13 |
841 |
29×29 |
1003 |
59×17 |
These numbers mean two things. First, the total speed ratio is "taken from the nearest" rather than "rounded" - if you want 150, the nearest 143, the deviation is −4.67%; if you want 1,000, the nearest 1,003, the deviation is +0.30%. Secondly, you cannot write casually which of the two numbers in the combination is the high-speed end. Note 2 at the top of sample table 8-8 is clear: the high-speed end takes the smaller reduction ratio, and the low-speed end takes the larger end (except for the speed ratio marked #). The 32 groups in Table 8-8 always have the larger end printed in front. When reading the table, first press Note 2 to identify which end is connected to the high-speed end. Box 437 in the table is extracted as it is from the sample. See the next section for the correct value.
2. The combination table itself must also be checked: product review plus output speed back calculation
When you get the combination table, your starting hand is not a copy of the number but a priori number. In the same catalog, Table 8-3 (speed ratio table, printed page 567) and Table 8-8 (two-stage reducer load capacity table, printed page 574 onwards) both list these 32 combinations, but the printed values in the two places do not match the product.
In Table 8-3, the total speed ratio of the 43×11 square is printed as 437, and the total speed ratio of the 87×71 square is printed as 6 117. And 43 × 11 = 473, 87 × 71 = 6 177. Table 8-8 shows exactly these two numbers printed by colleagues. They are not simply copied wrongly and can be independently verified.
The verification method is the second data provided by the sample itself: the "output speed" line in the header of Table 8-8 indicates the input speed 1 500 r/min. The output speed and the total speed ratio are reciprocal of each other, and the two columns must be self-consistent, which is the second piece of evidence:
combination |
Table 8-3 Print value |
Calculate the output speed according to the printed value |
Table 8-8 Printed output speed |
Calculate the output speed inversely based on the product |
determination |
|---|---|---|---|---|---|
43×11 |
437 |
3.43 |
3.2 |
3.17 |
Should be 473 |
87×71 |
6 117 |
0.245 |
0.24 |
0.243 |
Should be 6 177 |
Two pieces of evidence point to the same conclusion: 43×11 corresponds to 473, and 87×71 corresponds to 6 177. The two columns in Table 8-3 are printing errors. If you check the load capacity table or the nameplate, the speed ratio will be calculated incorrectly. The remaining 30 groups have completely consistent printed values between the two tables; the output speed line in Table 8-8 is also consistent with the reciprocal of the total speed ratio, 30 of the 32 groups are consistent with two significant digits, and the 99 and 1 505 groups are just 0.05 and 0.007 level truncation differences caused by positioning. This method is vendor-independent and can be transferred to any two-stage speed ratio.
3. Calculation example: speed ratio splitting, inter-stage parameters and frame number selection
3.1 Fixed overall speed ratio
Assume that the motor is 5.5 kW, the input speed is 1 500 r/min, and the required output is 8 r/min. The theoretical total speed ratio is 1 500/8 = 187.5, the nearest value in 32 groups is 187 (17×11), the deviation is −0.27%, and the actual output is 1 500/187 = 8.02 r/min. According to Note 2, the high-speed end takes 11 and the low-speed end takes 17.
3.2 Costs of two splits
The same overall speed ratio, which stage is broken down into a larger speed ratio, the working conditions between stages are very different. Take 187 (17×11) as an example: when the high-speed end is 11, the inter-stage speed is 1 500/11 = 136.4 r/min, and the inter-stage torque is converted from the input 35.02 N·m to 355 N·m. If the high-speed end is driven at 17, the inter-stage speed drops to 88.2 r/min, but the inter-stage torque rises to 549 N·m, which is 35.3% higher. The inter-stage shaft diameter is roughly estimated to increase by about 1 mm based on the cubic root of torque.
Inertia conversion is the other direction. The inertia of the inter-stage rotating group is converted to the motor end by dividing it by the square of the first-stage speed ratio. Take 11 divided by 121, take 17 divided by 289, and the difference is 2.39 times. The servo drive is sensitive to the converted inertia ratio and the setting margin. It is more advantageous to have a larger first-stage speed ratio. The two requirements point to different choices, and we need to return to the working conditions: heavy-load continuous operation depends on the inter-stage shaft and bearings, and the high-frequency start and stop of the servo depends on the converted inertia. The interstage shaft and bearings are calibrated in accordance with GB/T 275-2015 "Rolling Bearing Cooperation"; the general technical conditions are in accordance with JB/T 2982-2016 "Cycloidal Pinwheel Reducer", and the load-bearing capacity and efficiency are measured in accordance with JB/T 12931-2016.
3.3 Check the load capacity table, select the machine base number, and then check in reverse
Table 8-8 is divided by total speed ratio and by frame number, giving the input power and output torque of each combination. The following table is an excerpt of 187 columns, cross-checked using η = T·n₁/(9550·P·i) inverse calculation efficiency.
Base number |
Input power kW |
Output torque N·m |
Back calculation efficiency |
Whether it meets 5.5 kW and 5 600 N·m |
|---|---|---|---|---|
8115A |
0.40 |
405 |
0.850 |
dissatisfied |
8160A |
1.50 |
1 520 |
0.851 |
dissatisfied |
8175B |
2.71 |
2 750 |
0.852 |
dissatisfied |
8185B |
4.02 |
4 070 |
0.850 |
dissatisfied |
8190B |
5.62 |
5 690 |
0.850 |
satisfy |
8195B |
6.00 |
6 079 |
0.851 |
satisfy |
The power or torque of 8175B and below is not satisfied; 8190B is a just enough gear, with an input of 5.62 kW, an output torque of 5 690 N·m, and a torque margin of 1.6%; the 8195B is also satisfied, but 6 kW means that the motor needs to be enlarged by one gear, which is not necessary since the motor has been determined.
Use the grid of 8190B to make a closed loop: η = 5 690×1 500/(9550×5.62×187)=0.8504, and replace the output torque with 9 550×5.62×0.8504×187/1 500=5 690 N·m, the deviation from the printed value is 0.00%, and the sixth-speed efficiency falls between 0.850 and 0.852.
Spreading the 187 columns into 18 gears, the efficiency is not uniform: except for 8095A and 8145B, the back calculation of the other 16 gears is between 0.850 and 0.857; the power of 8095A is only 0.12 kW, and rounding makes the back calculation bias to 0.896, which is normal. One row of 8145B prints 0.85 kW with 961 N·m, and the back calculation η=0.950, which is obviously out of the range of the same column; while the back calculations of the four columns of 143, 165, 195, and 231 are all around 0.854, and only the 187 column is out of bounds, and the problem lies in this cell. Based on the inference of η=0.855 and P=0.85 in the same column, the torque in this grid should be about 865 N·m, and the printed 961 is 96 N·m higher. If it is read as 861, the efficiency returns to 0.851, which is consistent with the adjacent column. The capacity tables themselves also harbor typographical inconsistencies, again discovered by cross-checking rather than read-through.
4. Selection Steps to check with arrival
Organized into executable order:
The output speed and torque are determined by the load, and the theoretical overall speed ratio is calculated using the input speed;
Check the two-stage combination table to get the nearest value. According to Note 2, split it into two sections with a small high-speed end and a large low-speed end. Note the exception #;
Use product review plus output speed back calculation to check the combination table itself;
In the corresponding total speed ratio column of the load-carrying capacity table, screen the machine base number according to power and torque at the same time;
Use η = T·n₁/(9550·P·i) to back-calculate the efficiency for closed-loop checking, and scan the out-of-bounds grid line by line;
Check the inter-stage shaft and bearing according to the inter-stage speed and torque, and calculate the converted inertia for servo applications;
Upon arrival, check the total speed ratio and two-stage speed ratio on the nameplate, and do not refer to the printed value in the sample.
The two-stage speed ratio cannot be determined, and most likely it is stuck in two places: first, treating the total speed ratio as a continuous number, ignoring that it is only on a discrete grid; second, directly copying the sample value, forgetting that the table itself may be misprinted. By adding the product review and the back calculation of the output speed to the Selection process, there will be a basis for the judgment of these two steps. After the two-stage speed ratio, load-bearing capacity and frame number are complete, you can contact Hangzhou Weigao Transmission for reducer consultation. We also provide hard tooth surface reducers, worm gear reducers and gear reduction motors.