How to detect early fracture of ZLYJ173 reducer gear
Publish Time: 2026-10-28 Origin: Site
1. Online preliminary judgment without disassembly (daily inspection)
This is the earliest link to detect abnormalities, and basic troubleshooting can be completed without downtime:
1. Identification of abnormal noise characteristics: If periodic "clunking" or "clicking" impact sounds occur during operation, instead of a normal and uniform low-frequency buzzing sound, especially when the abnormal noise is significantly aggravated at the moment of starting and stopping, it indicates that there are local defects in the gear meshing area, and micro-cracks in the tooth root have begun to expand under alternating loads.
2. Vibration threshold determination: Use a vibration meter to detect the position of the box bearing seat. If the radial vibration speed exceeds 7.1mm/s (the normal operating threshold of this type of hard-tooth surface reducer), and after the bearing fault is eliminated, a sideband surrounding the gear meshing frequency appears in the spectrum, indicating that the gear meshing stiffness has undergone periodic mutations, which is a typical signal of early fracture.
3. Temperature abnormality warning: During normal operation, the surface temperature of the box should be stable at 40~60°C. If the temperature suddenly rises above 70°C with the load unchanged, and the local temperature rise gradient exceeds 10°C, it will indicate uneven gear meshing and increased friction in the micro-crack area, and an in-depth inspection must be arranged immediately.
4. Rapid oil screening: Take an oil sample from the bottom of the box and use a magnet to absorb the oil for observation. If ferromagnetic metal particles larger than 0.3mm in size are found and the particles are in the shape of fine fragments, it means that micro-flaking has occurred on the tooth surface and tooth root cracks have most likely occurred.
2. In-depth verification with professional instruments (precise measurement without stopping the machine)
For equipment that is initially judged to be abnormal, professional means are used to accurately locate early micro-cracks:
1. Vibration spectrum analysis: Install acceleration sensors at the box positions corresponding to the high-speed shaft, intermediate shaft, and low-speed shaft, and collect vibration signals for FFT analysis. If the time domain kurtosis index exceeds 4.5, the peak index is greater than 5, and there are side frequency bands separated by the gear rotation frequency on both sides of the meshing frequency in the spectrum, and the side frequency band energy accounts for more than 15%, it can be determined that the gear has the risk of early tooth breakage.
2. Acoustic emission detection: Acoustic emission sensors are used to capture the elastic waves released when gear cracks expand. This method is extremely sensitive to tooth root microcracks with a depth of less than 0.1mm. It can issue early warnings weeks before the cracks cause obvious vibration abnormalities. It is the best method for online monitoring of early fatigue fractures.
3. Infrared thermal imaging scanning: Use an infrared thermal imaging camera to scan the entire box surface. If an isolated local high temperature point is found in the box area corresponding to the gear mesh, and the temperature difference from the surrounding area exceeds 15°C, the specific location of the defective gear can be located and the area where early fracture occurs can be located.
4. Oil spectrum analysis: Perform elemental analysis on the oil sample. If the iron concentration increases by more than 30% within a week, and is accompanied by abnormal increases in gear material alloy elements such as molybdenum and chromium, it means that the gear metal matrix has continued microscopic spalling and early fractures are developing rapidly.
3. Shutdown, disassembly and inspection (final confirmation)
When two or more abnormalities occur in the above tests, the machine will be shut down for final inspection to accurately confirm the early fracture status:
1. Non-destructive testing: Open the observation hole and conduct magnetic particle testing or color penetrant testing on the tooth root stress concentration area. Superficial micro-cracks invisible to the naked eye can be directly discovered and the length, depth and direction of the cracks can be confirmed. This is the gold standard for determining early fractures.
2. Endoscope visual observation: Use an industrial endoscope to extend into the box and observe the tooth root transition fillet area of all gears throughout the process. If a subtle visible crack with a length of less than 5 mm is found at the tooth root, it can be determined as an early fracture risk, and replacement must be arranged immediately.
3. Tooth thickness and meshing clearance verification: Use a tooth thickness micrometer to measure the gear tooth thickness. If the tooth thickness wear exceeds 8% of the original design value, and the meshing gap increases by more than 20% compared with the factory standard, it means that the gear has been subjected to overload for a long time, the tooth root is already in a high stress state, and the risk of fracture increases significantly.