How to check the thermal power of the reducer: Why does it overheat when the mechanical power is sufficient - Hangzhou Weigao Transmission

Publish Time: 2026-10-16     Origin: Site

How to check the thermal power of the reducer: Why does it still overheat when the mechanical power is sufficient?

When selecting a reducer, only checking the mechanical parameters other than the thermal power of the reducer is a common cause of 'repeated overheating even though the power is clearly sufficient' on site. After many engineers press the output torque and speed ratio Selection, the oil temperature approaches the alarm value after the equipment has been running continuously for several hours. The root cause is that the mechanical power has passed the verification but the thermal power has not. This article explains clearly the difference between thermal power and mechanical power, calibration formulas and correction coefficients, as well as on-site countermeasures after tolerance is exceeded.

1. Thermal power and mechanical power are two independent limiting lines

Mechanical power is determined based on tooth surface contact, bending strength, and bearing life. The limit is 'how much torque it can withstand.' The thermal power limit is 'the power that can be transmitted when the oil pool temperature does not exceed the allowable value during continuous operation.' Gear meshing friction, bearing losses and oil churning losses will convert 2%–10% of the input power into heat (depending on the transmission efficiency of the reducer ). If the heat exceeds the heat dissipation capacity of the box, the oil temperature will continue to rise. According to the benchmark conditions of ISO/TR 14179: ambient temperature 25°C, oil pool temperature upper limit 95°C, natural convection in large indoor spaces. If the oil temperature exceeds the limit for a long time, the viscosity of the lubricating oil will decrease, the oil film will become thinner, and tooth surface gluing and bearing peeling will ensue. This also explains why when investigating the cause of reducer heating , insufficient thermal power is often misjudged as a lubrication failure.

2. Thermal power calibration formula and correction coefficient of reducer

The allowable thermal power Pt given in the general reducer sample is measured under reference working conditions (ambient temperature 20°C, continuous operation, power utilization 100%). When the actual working conditions are different, check as follows:

Pct = P2 × KT × KW × KP ≤ Pt

Among them, P2 is the actual transmitted power, and the meanings of the three correction coefficients are as follows:

coefficient

meaning

Value description

KT

ambient temperature coefficient

When the ambient temperature is higher than 20℃, it is greater than 1. The higher the temperature, the larger the value.

KW

Operation cycle coefficient

Intermittent operation can be taken as less than 1, continuous operation throughout the day can be taken as 1

KP

Power utilization coefficient

Determine by looking up the table based on the ratio of P2 to motor rated power.

Special reminder: The reducer service coefficient only covers impact load and mechanical fatigue margin, and cannot replace thermal power verification. The two lines must be calculated separately.

3. Five on-site factors affecting thermal power

  • Ambient temperature: Industry experience shows that the thermal power in a 40°C environment is about 30% lower than the 25°C benchmark. Special attention should be paid to high-temperature workshops and outdoor exposure situations.

  • Input speed: 3000 r/min. The heat generated during input is significantly higher than 1500 r/min, and the thermal power under high speed conditions may drop by about half.

  • Installation form: Vertical installation leads to poor heat dissipation and convection, and the thermal power is reduced by about 25%; confined spaces and dust-covered boxes will also weaken heat dissipation.

  • Gear form: The efficiency of worm gear reducer is only about 50%–90%, and the heat is concentrated on the worm side; the efficiency of hard tooth surface reducer (helical gear, spiral bevel gear) can reach 90%–98%, and the heat generation ratio is much smaller.

  • Lubricating oil: Selecting the wrong viscosity grade will affect both friction loss and heat dissipation. The reducer lubricating oil type and oil level specified in the sample should be filled. If the oil level is too high, it will intensify oil churning and heat generation.

4. Countermeasures for failure in thermal power verification

If Pct > Pt, the following measures can be taken in sequence: use a dilute oil station or fan for auxiliary cooling; improve ventilation around the box and remove dust; use shutdown to dissipate heat during intermittent working conditions; increase the frame number of the first gear; or change to a hard-tooth surface and planetary structure model with a larger thermal power margin. For large speed ratio and continuous operation conditions, it is recommended to directly provide the ambient temperature and input speed to the manufacturer during the inquiry stage, and require thermal power data to be issued based on actual working conditions.

5. Conclusion

The thermal power verification of the reducer is an indispensable step in the continuous operation of equipment: the mechanical power ensures that it can 'drive', and the thermal power ensures that it 'can rotate', both of which are indispensable. If you are working in a high-temperature workshop, high speed or large speed ratio, please contact Hangzhou Weigao Transmission . As a Hangzhou reducer manufacturer specializing in the R&D and manufacturing of reducers , we provide a full range of reducers and gear motors such as cycloid pinwheels, hard tooth surfaces, worm gears, and coaxial reduction motors. We support free verification of thermal power and mechanical power according to actual working conditions, and engineers will issue a complete solution within 24 hours. If you have any need for reducer Selection or replacement, please feel free to consult this reducer manufacturer at any time.。

FEEDBACK

How to determine the tooth profile code of worm gear reducer: ZA, ZI, ZN, ZK, ZC Selection comparison and calculation example - Hangzhou Weigao Transmission

What are the common problems with NGW42-25 planetary reducer base welding?

What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?

Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque

How to determine the displacement coefficient of the reducer gear: Examples of undercutting, tooth tip sharpening and center distance - Hangzhou Weigao Transmission