How to determine the displacement coefficient of the reducer gear: Examples of undercutting, tooth tip sharpening and center distance - Hangzhou Weigao Transmission

Publish Time: 2026-11-11     Origin: Site

In addition to the model and number of teeth, the reducer drawings are often marked with a series of numbers like x 1 = +0.30 and x 2 = −0.30, which are the displacement coefficients. It is not a decoration: if the number of teeth is less than a certain lower limit, undercutting will occur. If the number of teeth is enough but the center distance does not match the box body, it will not fit in either. The displacement coefficient is a means to solve these two problems at the same time.

1. Two hard constraints solved by the displacement coefficient

1.1 Undercut: The number of teeth cannot be lower than the lower limit

When using a standard rack tool to process an involute gear, if the number of teeth is too small, the top line of the tool tooth will cross the meshing limit point and cut off the formed involute tooth root. This is called undercutting, and the tooth root strength will be weakened. The minimum number of teeth to avoid undercutting is z min = 2h a * /sin 2α, where h a * is the tooth addendum height coefficient and α is the pressure angle. Taking h a * = 1 and α = 20°, substitute z min = 2/sin 220° = 17.10. In engineering, 17 teeth are used as the boundary.

When the number of teeth is insufficient, positive displacement can be used to move the tool outward by xm (x is the displacement coefficient, m is the module) to thicken the tooth thickness and tooth root, thereby avoiding undercutting. The corresponding minimum displacement coefficient is x min = ha * ( z min − z)/z min , and a margin should be left for the actual value.

Number of teeth z

Minimum displacement coefficient x min

Number of teeth z

Minimum displacement coefficient x min

12

0.2981

16

0.0642

13

0.2396

17

0.0057

14

0.1812

18

−0.0528

15

0.1227

20

−0.1698

1.2 Center distance: a of standard gears is fixed

The standard center distance of a pair of standard gears a = m(z 1 + z 2)/2 is directly calculated from the module and the number of teeth, and there is no room for adjustment. When the box hole spacing has been processed to a non-standard value, or if you want to reduce it Dimensions, you have to rely on displacement. According to the relationship between the total displacement coefficient and the center distance variation coefficient y = (a′ − a)/m, transmission is divided into three categories: height displacement (x 1 + x 2 = 0, a′ = a), positive angular displacement (x 1 + x 2 > 0, a′ > a) and negative angular displacement (x 1 + x 2 < 0, a′ < a).

There is an identity that is easily overlooked: as long as the calculation is carried out according to the formula, the head clearance will always remain c*·m regardless of height or angle displacement. In this example, m = 3 mm. The calculated head clearances of the three options are all 0.750 mm, which is exactly equal to 0.25m.

2. Calculation example 1: How to save the 13-tooth pinion gear

2.1 Parameters and solutions

Take the high-speed stage of a two-stage reducer: module m = 3 mm, pressure angle 20°, h a * = 1, c * = 0.25, speed ratio i = 4. In order to compress the axial size, z 1 = 13 for the small gear and z 2 = 52 for the large gear. Standard center distance a = 3×(13 + 52)/2 = 97.50 mm.

z 1 = 13 is lower than the 17-tooth limit, and the standard gear must be undercut. According to x min = 0.2396 and leave a margin, take x 1 = +0.30, and match x 2 = −0.30, which is a high degree of displacement. At this time, a′ = a = 97.50 mm, y = 0, and the tooth addendum height variation coefficient σ = 0.

project

Teeth 1 standard gear x=0

Tooth 1 after displacement x=+0.30

Tooth 2 after displacement x=−0.30

Tooth tip circle diameter da (mm)

45.000

46.800

160.200

Tooth root circle diameter df (mm)

31.500

33.300

146.700

Tooth tip height ha (mm)

3.000

3.900

2.100

Tooth root height hf (mm)

3.750

2.850

4.650

Indexing scallop thickness s (mm)

4.712

5.368

4.057

Tooth tip thickness sa (mm)

1.903

1.382

2.450

Ratio of tooth tip thickness to module sa/m

0.634

0.461

0.817

The diameter of the indexing circle d = mz, the diameter of the base circle, the module, and the pressure angle do not change with the displacement. What changes is the tip circle, the tooth root circle, the tooth thickness, and the tooth space width. After positive displacement of the pinion, the tooth root height is reduced from 3.750 mm to 2.850 mm, and the tooth root is thickened; after negative displacement of the large gear, the tooth addendum height is reduced from 3.900 mm to 2.100 mm, but the tooth addendum thickness increases to 2.450 mm. This is the distribution logic of height displacement: concentrate the displacement on the pinion with thin teeth and weak tooth roots.

2.2 Tip tip sharpening and interference check

Positive displacement thins the pinion tip. The tooth tip thickness is calculated according to s a = d a [π/(2z) + 2x·tanα/z + invα − invα a ], invθ = tanθ − θ (radians). Limits in Chapter 13 of 'Mechanical Design Manual': general gear s a ≥ 0.25m, quenched parts > 0.4m, this example is satisfied by 0.461. The transition curve interference is checked according to the two formulas in Table 13-1-5 of the manual, and the margins of 0.0279 and 0.0480 are both satisfied; the degree of coincidence ε α = 1.526, which is higher than the 1.2 limit.

2.3 What does the small number of teeth bring?

For the same speed ratio i = 4 and the same module, if the number of teeth is different, the center distance will be different: 97.50 mm for the 13-tooth solution, 127.50 mm for the 17-tooth standard solution, and 150.00 mm for the 20-tooth solution. The center distance of the 13-tooth displacement scheme is 30.00 mm less than that of the 17-tooth scheme, a decrease of 23.53%. This is the actual value of the displacement transmission with a small number of teeth: making the box smaller and flatter under the same load-bearing requirements, the premise is that the three tests of tooth tip thickness, interference, and coincidence are all passed.

x 1 value

Tooth 1 Tooth tip thickness sa/m

Tooth 2 Tooth tip thickness sa/m

Degree of coincidence ε α

Tooth 1 root circle df (mm)

Interference condition 1 margin

+0.20

0.5236

0.8055

1.554

32.70

0.0356

+0.25

0.4928

0.8113

1.540

33.00

0.0316

+0.30

0.4606

0.8167

1.526

33.30

0.0279

+0.35

0.4272

0.8217

1.511

33.60

0.0244

+0.40

0.3925

0.8262

1.495

33.90

0.0210

This table shows that the larger the displacement coefficient, the better. As x 1 increases, the tooth root circle increases and the tooth root strength increases, but the tooth tip thickness decreases all the way, and the coincidence degree and interference margin are tightened simultaneously. When x 1 = +0.40, s a /m drops to 0.3925, which is lower than the upper limit of 0.4m required for quenched gears. At this time, the displacement must be reduced, tooth tip trimming must be used instead, or the number of teeth must be retreated. The value range should be inferred from the most stringent limit.

3. Calculation Example 2: What to do if the center distance is reduced to 100 mm

3.1 Back calculation of meshing angle and total displacement coefficient

The box hole spacing requires a center distance a′ = 100 mm, which is 2.50 mm different from the standard center distance of 97.50 mm. This is a positive angular displacement. From cosα′ = (a/a′)cosα, we get cosα′ = (97.50/100)×cos20° = 0.9162, meshing angle α′ = 23.62°, and then use invα′ = invα + 2tanα(x 1 + x 2)/(z 1 + z 2) to solve for the total displacement coefficient x 1 + x 2 = 0.9076, and the center distance variation coefficient y = (100 − 97.50)/3 = 0.8333, tooth top height variation coefficient σ = x 1 + x 2 − y = 0.0743. Take x 1 = +0.50, x 2 = +0.4076.

project

numerical value

project

numerical value

Actual center distance a′ (mm)

100.000

Engagement angle α′ (°)

23.62

Total displacement coefficient x 1 + x2

0.9076

Center distance variation coefficient y

0.8333

Tooth tip height variation coefficient σ

0.0743

Head clearance c (mm)

0.750

Tooth 1 Addendum circle da (mm)

47.554

Tooth 2 Addendum circle da (mm)

164.000

Tooth 1 root circle df (mm)

34.500

Tooth 2 root circle df (mm)

150.946

Tooth 1 indexing circular tooth thickness s (mm)

5.804

Tooth 2 indexing circular tooth thickness s (mm)

5.603

Tooth 1 Tooth tip thickness sa/m

0.4401

Tooth 2 Tooth tip thickness sa/m

0.7733

End surface coincidence degree ε α

1.338

Interference conditions 1, 2 margin

0.0558, 0.0469

3.2 Cost of angle displacement

The positive angle displacement simultaneously thickens the tooth thickness of the two gears and widens the center distance. The tooth root strength and contact strength are improved, but the coincidence degree is reduced to 1.338, which is smaller than the 1.526 of the height displacement scheme. The rule is: the farther the center distance is, the larger the meshing angle will be, and the greater the loss of coincidence will be. If the center distance deviation of the box is very small, it is often safer to use height displacement instead.

4. How to verify the arrival of goods and how to check Selection

4.1 Use the length of the public normal line to back estimate the actual displacement coefficient

Whether the displacement coefficient is processed according to the drawing, it is most direct to measure the normal length W k . Formula W k = m·cosα·[(k − 0.5)π + z·invα] + 2x·m·sinα, k = αmz/1800 + 0.5 takes an integer. The latter term 2x·m·sinα is the displacement increment: when m = 3 mm, every 0.10 displacement coefficient corresponds to 0.205 mm, m = 4 mm corresponds to 0.274 mm, and m = 6 mm corresponds to 0.410 mm. Taking z = 13 and m = 3 as an example, the nominal W k = 4.974 mm for x = 0 and the nominal value of x = +0.30 is 5.590 mm; if the actual measurement is 5.590 mm, the back calculation x = (5.590 − 4.974)/(2×3×sin20°) = 0.300 is consistent with the drawing.

4.2 Selection and troubleshooting steps

  1. First determine whether the number of teeth exceeds the limit. Judge according to z min = 2h a * /sin 2α. The lower limit of straight teeth is 17 teeth when α = 20°; the helical teeth are converted according to the equivalent number of teeth z v = z/cos 3β. When β = 15°, z = 13 gives z v = 14.42. The minimum normal displacement coefficient is reduced to 0.156, which is looser than the 0.2396 of straight teeth.

  2. Then determine the transmission type. If the center distance is consistent with the standard value, use height displacement. If the center distance needs to be widened, use positive angle displacement.

  3. Assign the deformation coefficient. The small gear assumes positive displacement and the large gear assumes negative displacement, and starts with a margin of x min .

  4. Make three checks. Tooth tip thickness s a ≥ 0.25m (quenched parts > 0.4m), transition curve interference type, coincidence degree ε α ≥ 1.2, if any of them fails, adjust x or change the number of teeth.

  5. Calculate geometric dimensions and review loads. Draw the diagram according to da, df, s, s a , and then check the contact and bending strength according to GB/T 3480.2-2021 and GB/T 3480.3-2021; the simplified algorithm can be based on GB/T 10063-1988, which is applicable when the basic tooth profile complies with GB/T 1356, the rotation speed n ≤ 3600 r/min, and the indexing circle peripheral speed 1 m/s < v < In the case of 35 m/s, the two-stage peripheral speed in this example is 2.96 m/s.

  6. Arrival review. Use the length of the common normal to infer the actual x and check it with the drawing.

Boundary tip: The displacement coefficient is only applicable to involute cylindrical gear transmission. Worm gear reducers are implemented in accordance with GB/T 10085-2018 and GB/T 10088-2018, and cycloidal pinwheel reducers are implemented in accordance with GB/T 10107 series and GB/T 36491-2018. Neither of them can apply the formula in this article. If the drawing of the hard-tooth surface reducer is marked with both the displacement coefficient and the accuracy grade, the accuracy shall be in accordance with GB/T 10095.1-2022, and the two items must be checked separately.

The displacement coefficient is just a few numbers on the drawing, but the trade-off behind it is the balance of a set of constraints: the undercut gives the lower limit of the number of teeth, the center distance deviation determines the transmission type, and the three checks of tooth tip thickness, coincidence degree, and interference delineate the upper limit of the displacement. If you need to calculate the displacement plan according to specific working conditions, or compare and replace imported models, you can contact Hangzhou Weigao Transmission. We make hard tooth surface reducers, worm gear reducers, cycloidal pinwheel reducers and gear reduction motors, and can issue accounting opinions based on the number of teeth, center distance, accuracy level and temperature rise.

FEEDBACK

Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand

How to check the carrying capacity of worm gear reducer: working condition coefficient, efficiency and Selection calculation example - Hangzhou Weigao Transmission

Lubrication and maintenance characteristics of B series industrial gearboxes

What are the common misunderstandings in B series gearbox maintenance?

Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor