The whole process of reducer bearing replacement: pre-disassembly determination, clearance retest and hot assembly specifications - Hangzhou Weigao Transmission

Publish Time: 2026-10-18     Origin: Site

After the reducer bearing is replaced, it is more likely to heat up: the problem is mostly in the disassembly and assembly process

When on-site replacing reducer bearings , a frequent complaint is that 'the new bearing has been installed for less than a week and the temperature is higher than the old one.' After disassembly and re-inspection, three common reasons can often be found: wrong clearance group selection, thermal installation temperature out of control, and axial positioning failure to reset. The bearing itself is rarely the source of the problem. What really determines the life is the judgment before disassembly, the disassembly method and the retest after installation. This article into an executable process according to the on-site sequence , which is suitable for direct comparison between the equipment department and the maintenance team.organizes the judgment basis, clearance value and hot installation specifications of bearing replacement during reducer maintenance

Under what circumstances should you change: four objective criteria

If you shake the output shaft by hand and listen to the sound to determine whether to replace it, the misjudgment rate is very high. It is recommended to collect four sets of data of vibration, temperature, clearance and oil sample at the same time. If any one of them crosses the line, arrange a shutdown to avoid treating the abnormal noise of the adjustable reducer as a bearing scrap.

criterion

normal range

Need to shut down for inspection

Measurement location

Vibration acceleration

≤0.1g, no bearing characteristic frequency

Rising above 0.2g, the spectrum shows inner/outer ring fault frequencies.

One point each in the axial and radial directions of the bearing seat

Bearing seat temperature

40~65℃, 15~30℃ higher than the environment

Higher than 80℃ or the temperature rises more than 5℃ per hour

Bearing seat outer surface, infrared temperature measurement

Radial clearance

Within the selected clearance group

It exceeds the upper limit of the group by 1.5 times, or there is obvious looseness.

Dial indicator lifting method, rotate three 120° positions and average

Oil particles

No metal particles larger than 50μm

Flake or powdered iron filings attached to the magnetic plug

Oil drain port sampling, magnet adsorption preliminary judgment

If the equipment is approaching its rated life, replacement can also be planned in advance. According to ISO 281, the basic rated life L10=(C/P)^p (ball bearing p=3, roller bearing p=10/3), converted hours L10h=L10×10⁶/(60n). The common L10h interval for gearbox equipment is 20,000 to 40,000 hours. The maintenance node should be converted into 60% to 70% based on this for heavy load impact conditions. It should be noted that failures caused by poor lubrication account for more than 40% of bearing failures. Therefore, when replacing bearings, be sure to check the reducer lubricating oil model and oil level simultaneously, otherwise the service life of new parts will also be reduced.

Preparation before disassembly: Checking spare parts takes more time than disassembly and assembly

It is standard action to shut down the machine, cut off the power and tag out, drain the lubricating oil in the tank, and prepare the oil receiving tray. What is really easy to make mistakes is the check of spare parts: Bearings with the same inner diameter may have different clearance groups of CN, C3, and C4. There is no difference in appearance, and incorrect installation means rework. When checking, confirm four items: model suffix (clearance group, sealing type), cage material, whether it is a matching part, and whether the retaining ring and oil seal in The disassembly sequence is 'outside first, then inside, up first then down'. The removed gears, spacers, and end cover gaskets are numbered by position and photographed. Once the installation direction and meshing relationship of the gears are reversed, the reducer accessories are prepared in the same batch. abnormal noise from the reducer will almost certainly occur.

Clearance retest: C3 or CN, numbers have the final say

When the new bearing is not installed, first measure the radial clearance and compare it with the standard value to confirm whether the one given by the supplier is in the group required by the drawing. Take commonly used deep groove ball bearings as an example (GB/T 4604, unit μm, no-load measurement value):

Nominal inner diameter d (mm)

C2

CN (standard)

C3

C4

30~40

1~11

6~20

15~33

28~46

40~50

1~11

6~23

18~36

30~51

50~65

1~15

8~28

23~43

38~61

65~80

1~15

10~30

25~51

46~71

The logic of group selection is not complicated: when the inner ring has an interference fit and the temperature of the inner ring is higher than that of the outer ring, part of the clearance will be eaten up after installation. Usually, C3 is selected; the high-speed end of the reducer input shaft and the motor end mostly use C3 or CM group; the low-speed and heavy-load output end is executed according to the drawing, and do not enlarge at will. The impact of the interference on the clearance can be roughly estimated as the inner ring raceway expands by about 80% of the interference, and the outer ring shrinks by about 70% of the interference. Therefore, 'the greater the interference, the safer' is a misunderstanding - excessive interference may press the working clearance to zero, which directly manifests as heat jamming.

Hot loading specification: 120℃ is the upper limit, not the target

Small bearings with an inner diameter of less than 50mm can be installed by tapping the inner ring with a copper rod. The tapping point is only allowed to fall on the inner ring. It is strictly prohibited to tap the outer ring and cage. All medium and large sizes are hot-loaded: the oil bath is heated at 80~120℃ and kept warm for 15~20 minutes to allow the inner and outer rings to expand evenly; if possible, use an induction heater and an infrared temperature measuring gun to confirm point by point. It is strictly forbidden to use an acetylene flame or a blowtorch to bake directly. Local overheating will cause the ferrule to anneal. If the ferrule is reinstalled after the hardness drops, the service life may be only half of the design value. The heated bearing should be pushed until it is tight against the shaft shoulder at one time. It must not rotate during the cooling process, and do not use compressed air to quickly cool it.

Fit, positioning and sealing: three details determine the repair rate

The journal usually uses k6 or m6 transition fit, and the seat hole usually uses H7. Use a micrometer and inner diameter gauge to measure before assembly. Don't just look at the drawings. The axial positioning must be reset to the correct position: the elastic retaining ring must be completely dropped into the groove, the end cover gasket must be replaced according to the original thickness, and the tapered roller bearing and angular contact bearing must also be adjusted according to the axial clearance of 0.01~0.05mm. If it is too small, it will generate heat, and if it is too large, the rotation accuracy will decrease. The oil seal lip faces the oil chamber side. Apply a small amount of grease before assembly. Once the lip is scratched by the keyway or thread, the oil leakage will reappear within two weeks. This is also an often overlooked After assembly is completed, turn the car manually and the rotation should be even and without jamming.reason for reducer oil leakage .

Trial operation acceptance: three data files

Add oil to 1/2~2/3 of the oil level, run without load for 30 minutes, record the temperature, vibration value and current of the bearing seat; then gradually load and run stably for 2 hours before retesting. Judgment criteria: The temperature rise is stable and does not continue to climb, the vibration returns to within 0.1g, and there is no metal friction sound. Compare these three sets of data with those before replacement and archive them so that you can have a baseline for next judgment. In daily reducer maintenance , it is recommended to take an oil sample every 3 to 6 months, and grease the grease-lubricated parts every 3,000 to 5,000 hours. Remove old grease before replenishing, and greases of different brands must not be mixed.

The replacement of reducer bearings seems to be a replacement of parts, but it is actually a recurrence of assembly accuracy: correct clearance group, stable hot installation temperature, and accurate axial positioning. These three factors determine how long the new bearing can run. Hangzhou Weigao Transmission provides hard-tooth surface reducers, cycloidal pinwheel reducers, worm gear reducers and gear reduction motors as well as complete machines and reducer accessories . You can check the bearing model, clearance group and oil seal specifications according to the original machine nameplate and drawings. If you are arranging maintenance or need a spare parts list, please contact this local reducer manufacturer in Hangzhou to obtain reducer consultation and reducer quotation . Engineers can help calculate the radial load of the reducer and issue a replacement plan; search for Hangzhou reducer manufacturers and arrange for technicians to come to the factory to confirm the installation dimensions.

FEEDBACK

What is the clearance standard of P series planetary reducer under different working conditions?

How to choose the P series planetary reducer suitable for your equipment

How to detect early fracture of ZLYJ173 reducer gear

How to judge the degree of breakage of ZLYJ series reducer gears by listening to the sound

What are the common causes of failure of NGW102-6 planetary reducer bearing components?