The relationship between servo reducer backlash and positioning accuracy: error conversion, accuracy grade and Selection key points - Hangzhou Weigao Transmission

Publish Time: 2026-10-13     Origin: Site

On servo-driven automation equipment, the reducer backlash (return clearance) of the servo reducer is the first parameter to be looked at when Selection: the tiny angle at which the input shaft can be idle when the input shaft is fixed and the output shaft is switched forward and reverse. The unit is arcmin (arcmin, 1°=60′). It seems static, but in fact it will become a positioning deviation at the load end at the moment of reversal. It is a common misjudgment to equate backlash with positioning accuracy - the accuracy of equipment parking depends on the error budget after the superposition of backlash, torsional stiffness, inertia matching and structural rigidity. This article breaks down these items and explains them clearly, and provides a conversion table and key points.

1. First, distinguish the concepts: backlash, repeatable positioning accuracy and absolute positioning accuracy

These words are often used interchangeably. Reducer backlash describes the angular backlash of the gear pair when switching forward and reverse, which affects reverse positioning and reversal response; repeat positioning accuracy is the consistency of returning to the same target point multiple times, which is affected by backlash, friction and rigidity; absolute positioning accuracy is the deviation between the actual position and the command position, and is also affected by zero-point calibration and transmission errors. It can be seen that the accuracy of the servo reducer is not a single parameter, but an error budget.

2. Where does the backlash of the servo reducer come from? How to classify accuracy levels

The essence of backlash is the dead zone caused by the superposition of gear pair backlash, bearing clearance, assembly tolerance and thermal expansion. It is not a defect, but a margin that must be retained in the transmission: tolerances are required for tooth thickness and center distance, clearance is required for bearings, and oil film space is required between tooth surfaces. Therefore, the engineering goal is not 'zero backlash', but controllable and repeatable low backlash. The industry divides the accuracy levels of based on return clearance values precision planetary reducers :

Accuracy level

Return clearance

Typical application scenarios

Standard type

8~16 arc minutes

Conveyor lines, mixing equipment, general material handling

Low backlash type

5~8 arc minutes

Packaging machinery, textile machinery, general automated positioning

Precision type

≤3 arc minutes

CNC feed axis, robot joint, positioning turntable

Ultra high precision type

≤1 arc minute

Semiconductor transmission, precision testing instruments, medical equipment

The total backlash of a two-stage or three-stage reducer is the superimposed value of the clearances at all levels. The figures in the single-stage product catalog cannot be copied and should be calculated based on the entire machine.

3. How to convert backlash into load-side error

To judge whether the angular minute is enough, it must be converted to the load end displacement: Δs = r × Δθ, where 1 arc minute ≈ 0.000291 rad. For the same 1 arc minute, the larger the working radius, the more considerable the circumferential air travel is.

working radius r

1 arc minute corresponds to displacement

Displacement corresponding to 3 arc minutes

50mm

About 0.015mm

About 0.044mm

100mm

About 0.029mm

About 0.087mm

200mm

About 0.058mm

About 0.175 mm

500mm

About 0.145mm

About 0.436mm

Take a workstation with a 200 mm radius slewing arm at the output end as an example: If a servo reducer with a radius of ≤3 arc minutes is used , the backlash alone will bring about 0.17 mm of air travel during reversal; if the process only allows ±0.05 mm, this level is not applicable, and the accuracy level needs to be increased or the force arm needs to be shortened. Therefore, 'Is 1 arc minute accurate enough?' is a false proposition. The correct question is: What are the working radius and allowable error?

4. Just focusing on the backlash is not enough: torsional stiffness determines the loading accuracy

Backlash only takes effect at the moment of reversal; after the tooth surfaces are refitted, the continued application of torque will cause the gear, shaft and box to elastically deform, and errors will continue to exist. The simplified relationship is: angular elastic error (arcmin) = applied torque (N·m) ÷ torsional stiffness (N·m/arcmin). Assuming that the stiffness of a reducer is 20 N·m/armin and the load torque is 200 N·m, the elastic error is 10 arcmin; with a superimposed backlash of ≤3 arcmin, the comprehensive error of full-load commutation is close to 13 arcmin, and the backlash accounts for less than a quarter. This is the reason why two reducers with the same nominal backlash behave differently - torsional stiffness is the main variable of load accuracy.

5. Inertia matching and transmission series: hidden variables of dynamic accuracy

The static standard is met but the dynamic one is still shaking. The reason is mostly due to inertia matching: the load inertia converted to the motor side = load inertia ÷ speed ratio². For general applications, it is recommended that the ratio of load inertia to motor rotor inertia should be controlled within 5:1, and within high-precision applications within 3:1; when the ratio is too large, the servo gain cannot be adjusted, and speed fluctuations and stop overshoots will occur. Calculating the load inertia and then deducing the matching relationship between the motor power and the reducer is more effective than simply amplifying the reduction ratio. It should also be noted that the more stages, the greater the total backlash: the single-stage efficiency is about 95% to 97%, and the two-stage efficiency is about 92% to 95%, which should be weighed according to the working conditions.

6. Quick check on key points of servo reducer Selection

The return clearance is graded after conversion according to the working radius: handling and conveying can be relaxed to 5 to 16 arc minutes, and the robot joint and CNC axis are recommended to be ≤ 3 arc minutes; the torsional stiffness in heavy-load and precision positioning situations is recommended to be no less than 20 N·m/ar minute; the inertia ratio is controlled at 5:1 or 3:1; the output end flange stop is matched to 0.02 to 0.05 mm, and the coaxiality is ≤ 0.05 mm to avoid damaging the stop by knocking the assembly. Multi-point positioning equipment should also enable backlash compensation and measure repeated positioning and backlash errors.

Conclusion: Accuracy comes from "budgeting", not picking it out

The reducer backlash and positioning accuracy of the servo reducer are a relationship between 'a source of error' and 'overall machine performance': the backlash determines the reversing air travel, the torsional stiffness determines the load deformation, the inertia matching determines the dynamic following, and the installation coaxiality determines the long-term stability. Split the allowable error and allocate it by link, and then backtrack on how much margin should be left for each item, so as to avoid over-allocation and degradation Selection.

Servo reducer Selection Not sure? Contact Hangzhou Weigao Transmission

Hangzhou Weigao Transmission Machinery Co., Ltd. is a reducer manufacturer specializing in the manufacturing of transmission equipment . The product line covers cycloidal pinwheel reducers, hard tooth surface reducers, coaxial reducers, NMRV worm gear reducers, gear reduction motors and precision transmission series. It can provide matching solutions according to servo motor flange, load inertia and allowable backlash. Send us the working radius, allowable error, load torque and servo motor model, and the engineer will complete the reducer consultation and error calculation for free. As based in Hangzhou a Hangzhou reducer manufacturer , we support customized drawings and samples and compare them with imported brand models. Welcome to call us for negotiation.

FEEDBACK

Desalination Plant Gearbox Market 2027: SWRO Pump Drive Demand

How to determine the tooth profile code of worm gear reducer: ZA, ZI, ZN, ZK, ZC Selection comparison and calculation example - Hangzhou Weigao Transmission

What are the common problems with NGW42-25 planetary reducer base welding?

What kind of noise will the reducer produce if the box manufacturing accuracy is not up to standard?

Slewing Drive Solar Tracker Selection: Wind Load and Holding Torque