The difference between hard tooth surface reducer and soft tooth surface reducer and Selection suggestions - Hangzhou Weigao Transmission
Publish Time: 2026-10-11 Origin: Site
In the process of reducer production, one of the most common questions encountered by procurement engineers is: What is the difference between With the same power and the same speed ratio, the price and service life of the two gearboxes are quite different. This article compares two types from the four dimensions of tooth surface hardness, load-bearing capacity, accuracy and cost, a hard-tooth surface reducer and a soft-tooth surface reducer ? of reducers and gives practical suggestions.
What is a soft tooth surface reducer?
The gears of soft tooth surface reducers are usually quenched and tempered, and the tooth surface hardness generally does not exceed 286HB (about 300HB or less). It is characterized by simple process, low manufacturing cost and good running-in performance - the gear pair automatically corrects small manufacturing and installation errors through slight wear during initial operation, so it is not sensitive to impact loads. Common soft tooth surface products include ZQ/ZL series cylindrical gear reducers and reducers for some lifting machinery. The disadvantage is that the load-bearing capacity is limited, the tooth surface is prone to pitting and gluing when running at full load for a long time, and the service life is relatively short.
What is a hard tooth surface reducer?
The gears of the hard-tooth surface reducer are carburized, quenched or nitrided, and the tooth surface hardness reaches HRC58-62. The gear grinding process must be subsequently performed to eliminate thermal deformation. Its outstanding advantages are: load capacity per unit volume is 2-4 times higher than that of soft tooth surfaces, high transmission accuracy (up to level 5-6 of GB/T 10095), low noise, small temperature rise, and long service life. Typical products include hard-toothed cylindrical gear reducers, cycloidal pinwheel reducers and various servo planetary reducers. The price is complex manufacturing process, higher price, and stricter requirements on lubricants and installation accuracy.
Comparison of core differences between hard tooth surface and soft tooth surface
Comparative item | Hard tooth surface reducer | Soft tooth surface reducer |
|---|---|---|
Tooth surface hardness | HRC58–62 (carburizing and quenching + gear grinding) | ≤286HB (quenching and tempering treatment) |
Carrying capacity | High, small size, high power density | Lower, requires larger cabinet |
Transmission accuracy | Level 5–6, low noise | Level 8–9, higher noise level |
Service life | Long term (more than 10 years of continuous operation) | Short, prone to pitting under heavy load |
price | higher | 低 |
Typical applications | Continuous production lines, metallurgy, mining, wind power | Intermittent working conditions, light load conveying, lifting |
Four practical suggestions for reducers Selection
Look at the continuity of working conditions: for production lines that run continuously for more than 8 hours a day or 24 hours a day, hard-tooth surface reducers are preferred ; soft-tooth surfaces can be used to reduce costs in intermittent and light-load situations.
Look at the space and weight restrictions: When the installation space is limited, a hard-tooth surface gearbox that provides the same torque in a smaller volume is the preferred solution.
Calculate the accurate service coefficient: No matter what kind of tooth surface, the reducer Selection must check the service coefficient (generally 1.5-2.0 for continuous working conditions), thermal power and cantilever load to avoid 'a small horse pulling a big cart'.
Pay attention to the whole life cycle cost: the purchase price of hard tooth surface reducer is 30%-60% higher, but it has a long life and less downtime. In most industrial scenarios, the overall cost is lower.
Weigao Transmission Selection supports
Hangzhou Weigao Transmission Machinery Co., Ltd. specializes in the production of cycloidal pinwheel reducers , hard-tooth surface cylindrical gear reducers, gear reduction motors and other series of gearbox products. It supports free Selection calculations based on working condition parameters. If you have difficulty choosing between hard tooth surface and soft tooth surface, please provide the motor power, input speed, output torque and daily running time. Our engineers will provide you with a Selection plan and quotation. Welcome to send us drawings or letters for consultation.