How to adjust and repair the gear backlash of the reducer if it is too large or too small?

Publish Time: 2026-11-03     Origin: Site

1. The machine must be shut down, powered off, and allowed to cool completely before operation to avoid accidental injury.

2. Use a feeler gauge, dial indicator or lead wire method to accurately measure the current gap, and check at three points along the tooth width, the front, middle and back. The difference should not exceed 0.05mm.

3. Confirm the standard clearance according to the type of reducer: general helical gear 0.10-0.35mm, worm gear 0.15-0.3mm, standard planetary reducer 8-15 arc minutes.

2. Repair plan for gaps that are too small

If the gap is too small, it can easily lead to stuck teeth, poor lubrication, and excessive temperature rise. It can be handled according to the following steps:

1. Adjust the gasket to enlarge the center distance: disassemble the box and add a 0.05mm grade thin copper gasket to the bearing seat to increase the gear center distance and gradually enlarge the meshing gap.

‌2. Fine-tune the shafting position‌: Loosen the gear fixing bolts, fine-tune the shafting away from the meshing surface, and retest the clearance after each movement of 0.05mm.

‌3. Slightly grind the tooth surface‌: If there is local tooth surface interference, use a whetstone or fine grinding wheel to lightly grind the high points to avoid large-area grinding from damaging the tooth profile accuracy.

4. ‌Verify the meshing status‌: After adjustment, there is no jamming during the manual turning process. The red lead coloring check shows that the contact spots fall on more than 70% of the middle of the tooth surface.

3. Repair plan for excessive gaps

If the gap is too large, it will easily cause impact between teeth and intensify noise and vibration. Repairs are graded according to the degree of wear:

1. Gasket adjustment to reduce center distance‌: Take out part of the thin copper gasket at the bearing seat, reduce the gear center distance, and return the gap to the standard range.

‌2. Fine adjustment of axial position‌: For bevel gear reducers, increase or decrease the axial spacer at the rear end of the main and driven bevel gears to bring the gears closer in the axial direction and reduce the meshing backlash.

‌3. Tooth surface wear repair‌: For slight wear, use brush plating to coat a 0.05-0.5mm nickel-based alloy layer; for moderate wear, use laser cladding and surfacing wear-resistant alloy, and then grind to restore the tooth profile accuracy.

‌4. Replace gears in pairs‌: When the gap exceeds 0.8mm and large areas of pitting or peeling occur on the tooth surface, new gears of the same specification and material must be replaced in pairs to avoid mismatch in thickness of the old and new teeth.

4. Key points for post-repair acceptance and pit avoidance

After repair, run without load for 2 hours, and monitor the temperature rise to ≤80°C, and there is no abnormal noise or vibration.

Load to 50%, 80%, and 100% rated load and run for 1 hour each, and there is no obvious change in the retest gap.

It is strictly forbidden to adjust the gap to 0, as thermal expansion will directly hold the shaft and break the teeth; all locking bolts must be filled with anti-loosening glue to prevent recurrence of gaps caused by high-frequency vibration.

When new and old gears are used together, the initial clearance needs to be appropriately increased to compensate for the difference in wear to avoid jamming during operation.

FEEDBACK

Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand

How to check the carrying capacity of worm gear reducer: working condition coefficient, efficiency and Selection calculation example - Hangzhou Weigao Transmission

Lubrication and maintenance characteristics of B series industrial gearboxes

What are the common misunderstandings in B series gearbox maintenance?

Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor