Structural characteristics and Selection key points of helical gear reducer: helix angle, axial force and application scenarios - Hangzhou Weigao Transmission

Publish Time: 2026-10-18     Origin: Site

Why are helical gear reducers so widely used?

Helical gear reducers are currently one of the most widely used models in general transmission equipment. R series coaxial, F series parallel shaft, K series bevel gear commutation and most hard tooth surface reducer product lines, the internal gears are mainly helical tooth structures. Unlike spur gears, which 'entire teeth come in and out of mesh instantly', there is a helix angle between the gear teeth of helical gears and the axis. During meshing, the contact line gradually transitions from the tooth end to the full tooth width, and the force increases from small to large and then from small to large, so the transmission is smooth and the impact is small. Industry measured data shows that the meshing noise of helical gears is 5 to 10 dB lower than that of spur gears of the same specification, and the single-stage transmission efficiency can reach 94% to 98%. This is the fundamental reason why it is equipped with a large number of gear reduction motors and used in continuous operation scenarios of conveyor lines and packaging machinery.

How to determine the helix angle: balance between stability and axial force

Helix angle β is the core parameter of helical gears, which refers to the angle between the gear teeth and the axis. The larger the helix angle, the greater the degree of coincidence, the smoother the movement, and the lower the noise; however, the axial component force also increases according to Fa=Ft×tanβ, which puts higher requirements on the bearings and box. The common values ​​and effects in the industry are as follows:

Helix angle range

Typical uses

Features

8°~15°

Heavy load, low speed, general purpose series

Small axial force, low bearing load, economical structure

15°~20°

Mainstream values ​​for conventional industrial transmissions

Taking into account both stability and axial force, the best versatility

20°~25°

Low noise requirements

The coincidence degree can reach 1.5~2.2, and the operation is quiet.

It should be noted that the axial force must be borne by the bearing: the single helical tooth structure is usually equipped with an angular contact ball bearing or a tapered roller bearing at one end, while the herringbone tooth (double helical tooth) uses left and right rotation to cancel each other out. If the equipment has reverse rotation or frequent starts and stops during Selection, it is recommended to confirm the bearing configuration and axial force calculation at the Selection stage of the helical gear reducer .

Coincidence and load-bearing: the strength of helical gears

The coincidence degree of spur gears is generally between 1.2 and 1.6, while the coincidence degree of helical gears can reach 1.5 and 2.2, that is, more gear teeth share the load at the same time. Combined with carburizing and quenching (tooth surface hardness HRC58~62) and gear grinding finishing (ISO level 5~6), the contact fatigue strength of the helical gear hard tooth surface reducer is significantly improved, the risk of pitting corrosion and tooth breakage is reduced, and the service life is longer in high-power, long-term continuous operation situations. At the same time, the progressive meshing of multiple pairs of teeth disperses the impact load, which is one of the reasons why heavy-duty industries such as metallurgy and mining generally use helical gears as the main model.

Helical gear layout techniques in multi-stage transmission

In two-stage and three-stage expanded structures, the rotation direction and helix angle of helical gears are usually designed in stages: the high-speed stage adopts a smaller helix angle to control the axial force, and the low-speed stage has large torque. Left and right helical gears can be arranged on the same axis to partially offset the axial force. This arrangement can reduce the size of the thrust bearing, reduce the probability of heat generation and abnormal noise of the reducer , and also facilitate the compactness of the box structure. When installing according to the standard , align and align reducer installation method (foot, flange, shaft mounting) to further ensure the meshing quality and bearing life.

Typical application scenarios and Selection suggestions

Helical gear reducers are commonly used in belt conveyors, screw conveyors, mixing equipment, packaging and food machinery, logistics sorting lines, etc. Selection It is recommended to grasp four points: first, determine the service coefficient according to the working condition coefficient, and appropriately amplify the impact load situation; second, check the thermal power, and pay attention to the upper limit of oil temperature in continuous heavy-load environments; third, confirm whether the radial and cantilever loads of the output shaft exceed the allowable value; fourth, make a comprehensive assessment based on the transmission efficiency of the reducer and the long-term operation power consumption. Every one percentage point increase in efficiency will save considerable electricity bills for one year of continuous operation of the equipment.

If you are choosing for conveying, mixing, packaging and other equipment a helical gear reducer or matching gear reduction motor , please contact Hangzhou Weigao Transmission . Weigao Transmission provides R/F/K/S series helical gears and hard tooth surface product lines, supports customization of non-standard speed ratios and mounting flanges, and can provide free calculation and quotation services based on your working condition parameters to help you choose the right transmission solution at the first time.

FEEDBACK

Pneumatic Conveying Gearbox Market 2027: Blower, Airlock and Screw Drive Demand

摆线针轮减速机两级速比怎么定:组合表怎么读、怎么校核、怎么落到机座号 - 杭州威高传动

Pellet Mill Gearbox Selection: Ring Die Torque, Thermal Rating and VFD Restart

Is there any way to reduce the parallelism error of the reducer?

Let me introduce in detail how to judge whether the worm gear joint surface of PWU160-40-V reducer is damaged.