Judgment and replacement cycle of pin tooth pin wear of cycloidal pinwheel reducer - Hangzhou Weigao Transmission
Publish Time: 2026-10-12 Origin: Site
In field failure cases of cycloidal pinwheel reducers , the wear of the pin tooth pins of the cycloidal pinwheel reducer appears very early, but is often misjudged as bearing failure. The pin tooth pin is small in size and is located in the inner ring of the pin tooth shell, making it inconvenient to disassemble and inspect. When the machine stops after hearing an obvious impact sound, the tooth surface of the cycloidal wheel is often damaged. The following is organized in the order of 'judge first, then quantify, and then determine the cycle' for reference by equipment maintenance personnel.
1. What role does the pin tooth pin play in the cycloid transmission?
The cycloidal pinwheel reducer relies on the small tooth difference between the cycloid wheel and the pin teeth for meshing and deceleration: the eccentric shaft drives the cycloid wheel to rotate eccentrically, and the cycloidal wheel tooth profile contacts the pin tooth pins fixed on the pin tooth shell in sequence. All the output torque of the whole machine is transmitted through the pin tooth pin. The same pin is repeatedly crushed dozens of times per minute. The contact frequency is much higher than that of a single tooth surface of ordinary gears, so it is particularly sensitive to the thickness of the anti-wear layer and lubricating film. Once the surface hardened layer is worn through, the wear of the rear section will be significantly accelerated. This is also the reason why the wear of the cycloid wheel always occurs immediately after the wear of the pin tooth pin.
2. Three stages of wear and corresponding signals
Early stage : The meshing gap increases slightly, there is a periodic slight sound synchronized with the speed, and there may be a slight crawling feeling under low speed conditions. At this time, the gap change can be detected with a feeler gauge, but the operating condition has not deteriorated significantly and can easily be ignored.
Mid-term : intermittent 'clunking' impact sounds appear, which are aggravated when the load fluctuates; the measured transmission efficiency may drop below 85%, and the temperature rise under the same load is 10~15°C higher than that of the new machine.
Later period : The output torque decreases, the load capacity decreases by more than 20%, there is a significant gap in starting and stopping, and the replaced oil quickly turns black and contains metal powder. If the output shaft shakes, the reducer bearing replacement needs to be evaluated as well.。
3. On-site judgment: look, touch and measure
Judgment cannot be based on a single phenomenon. It is recommended to follow three steps: appearance, feel, and measurement, and keep records one by one to compare wear trends.
Check items | method | Change criterion |
|---|---|---|
Pin surface | Visually and by touch along the axis, check for pitting, wear marks, and indentations. | You can clearly feel the rough texture, indicating that the hardened layer has been worn away. |
Pin diameter | External diameter micrometer to measure wear | If the wear amount exceeds 0.2mm, it needs to be replaced. |
Pin tooth pin hardness | Rockwell hardness sampling test | Lower than HRC58 indicates heat treatment failure |
Pin hole of pin tooth shell | Internal micrometer for measuring aperture | When the hole diameter is 10~20mm, the limit is about +0.037mm. If the tolerance is exceeded, the hole can be expanded and repaired. |
Meshing clearance | Feeler gauge measures the gap between the cycloidal wheel and the pin gear housing | If it exceeds 0.3mm, it needs to be replaced; if the deviation of each point exceeds 0.05mm, it means deformation. |
Bearing clearance | Feeler gauge to measure output shaft bearing radial clearance | If it exceeds 0.15mm, it needs to be replaced. |
Auxiliary signals during operation are also valuable: the vibration speed generally does not exceed 2.8mm/s, the oil temperature in the meshing chamber does not exceed 80°C, and the bearing end does not exceed 90°C. When the temperature rise exceeds 10°C per hour or a 'clicking' impact sound occurs, the machine should be shut down for disassembly and inspection. The sudden increase in the concentration of iron in the oil test is also evidence of increased wear of reducer parts .
4. How to determine the replacement cycle?
The pin tooth pin does not have a uniform fixed life. The cycle should be graded according to the intensity of the working conditions and bound to the oil change node to achieve "oil change and inspection". The following table can be used as the starting point for the internal control maintenance plan. The actual cycle needs to be adjusted based on the average daily operating hours and load rate.
Working conditions | Pin inspection cycle | Oil change interval | Whole machine maintenance node |
|---|---|---|---|
Light load continuous (mixing, conveying) | Approximately 4000 hours or every oil change | 500 hours for the first time, every 3000~4000 hours thereafter | Approximately 12 months of intermediate repair |
Heavy load, frequent starts and stops | About 2000 hours | First 300 hours, then every 2000 hours | Arrange in advance based on wear and tear records |
Dusty, hot and humid | Based on the above table, shorten it by 30%~50% | Shortened to 50%~70% of the regular cycle | Shorten and tighten seal checks |
The general practice is: medium maintenance is arranged on a 12-month basis, and the pin tooth sleeve, pin tooth pin, pin bushing, and pin shaft are inspected and replaced; overhaul is arranged on a 36-month schedule, which involves the inspection and repair of the cycloid gear and pin tooth housing. The above table is a reference range. If the equipment is overloaded for a long time or the safety factor is too small, the wear rate may increase exponentially.
5. Key points for replacement and assembly
The wear of the pin tooth pins is not synchronized. Mixing old and new ones will cause uneven stress on each tooth, which will accelerate the new wear. Therefore, the pin tooth pins and pin tooth sleeves should be replaced as a complete set. Pay attention to four points when assembling:
1. Before replacement, review the hole diameter, roundness and hole spacing error of the pin hole of the pin tooth shell. If the pin hole is out of tolerance, the hole must be enlarged and the insert sleeve will be installed, otherwise the new pin will still shake after being installed;
2. If the cycloidal wheel has peeling, pitting, or tooth thickness wear exceeds the limit, it should be replaced in pairs, and the phase mark should be made before disassembly;
3. After assembly, the meshing clearance is recommended to be controlled at 0.15~0.25mm, and the axial clearance of the cycloidal wheel is 0.2~0.25mm;
4. Thoroughly clean the iron filings and sludge at the bottom of the box before filling the oil. The first oil change should be performed every 300~500 hours.
If the same equipment has repeated reducer maintenance records in a short period of time, and the recurrence occurs soon after parts are replaced, it usually means that the safety factor is insufficient or the installation coaxiality is too poor. Replacement alone cannot cure the problem, and it is necessary to go back to the installation process for review.
6. Daily habits to extend service life
Protecting the pin tooth pin actually involves two things: keeping the lubricating film always present and keeping the contact stress within the design range. Pay daily attention to whether the oil level is at the center line of the oil mark, whether the breather cap is unobstructed, and whether there is any leakage; when starting, run without load for 3 to 5 minutes before loading; avoid long-term operation exceeding the rated load. When there is indeed an impact load under working conditions, the safety factor should be increased in the Selection stage instead of enlarging the machine base to carry it.
Cycloidal pinwheel reducer pins and accessories Selection, welcome to consult Hangzhou Weigao Transmission
Hangzhou Weigao Transmission Machinery Co., Ltd. produces cycloidal pinwheel reducers (including BLD and other series), hard tooth surface reducers, gear reduction motors, worm gear reducers and other transmission products. It can provide pins, pin tooth sets, cycloidal wheels, bearings and oil seals and other standing reducer accessories , and supports cycloidal pinwheel reducer model comparison and replacement of old machines. As specializing in transmission equipment , we can calculate a reducer manufacturer the reducer plan for free and provide a quotation based on the motor power, input speed, output torque, impact conditions and installation methods you provide, as well as a list of wearing parts and maintenance cycle recommendations. Welcome to send pictures, letters or calls for consultation.