Cause Analysis and Preventive Measures of Reducer Gear Pitting-Hangzhou Weigao Transmission
Publish Time: 2026-10-13 Origin: Site
Gear pitting corrosion of closed transmission reducer is the most common tooth surface fatigue failure: under the action of cyclically changing contact stress, fine cracks develop on the surface of the tooth surface. The lubricating oil squeezes into the cracks to form a hydraulic wedge effect, causing the surface metal to peel off, leaving pitted pits. Pitting pits mostly appear on the tooth root side near the pitch line - there are few teeth engaged at the same time, the contact stress is large, the relative sliding speed is low, and the oil film is not easy to establish. In the early stage, pitting corrosion only affects the smooth operation. Once it expands into pieces, the tooth profile is destroyed, the vibration noise increases, and in severe cases, the gear teeth may even break. This article combines on-site maintenance experience to analyze the four major causes of gear pitting corrosion and provides practical preventive measures.
1. Contact stress is too high: overloading and small Selection are the main reasons
The contact stress on the tooth surface exceeds the contact fatigue limit of the material for a long time, which is a direct cause of pitting corrosion. There are three common situations: Selection, the service coefficient value is low, and the starting impact and frequent forward and reverse operating conditions are not taken into account; the load increases after the equipment is modified, and the original hard tooth surface reducer is still used for support; the tooth width is blindly narrowed or the module is too small, and the unit tooth surface load is too high. Countermeasures: Recheck the torque and reducer service coefficient according to actual working conditions , and appropriately enlarge the specifications when the impact load is large; use helical gears instead of spur gears when conditions permit. Multi-tooth meshing can disperse the contact stress.
2. Materials and heat treatment: Insufficient hardness and thin hardened layer
Tooth surface hardness and hardened layer depth directly determine the contact fatigue life. The tooth surface hardness of carburized and quenched gears should be controlled at 58 to 62 HRC. When the depth of the hardened layer is insufficient, cracks will easily initiate in the transition zone between the hardened layer and the core, and then peel off in pieces (commonly known as spalling, the pit area is larger than pitting corrosion). For paired gears, it is recommended that the hardness of the pinion gear is 20 to 40 HB higher than that of the large gear, so that the pinion gear with more service cycles will fail later than the large gear; the tooth core must maintain sufficient toughness to avoid rapid expansion of cracks caused by hard surface and brittle core. In addition, the tooth surface roughness Ra≤0.8μm after gear grinding can significantly reduce surface microscopic defects that become the starting point of cracks.
3. Improper lubrication: the oil film cannot support the contact stress
The function of lubricating oil is to establish an elastohydrodynamic oil film between the tooth surfaces. If the viscosity is selected to be low, the oil temperature is too high, causing the oil film to become thinner, the oil to be oxidized and emulsified, or water to be mixed with iron filings, the metal micro-protrusions will be in direct contact, accelerating the formation of pitting corrosion of the reducer gear ; moisture entering the oil will also cause hydrogen embrittlement, further reducing the fatigue strength of the surface layer. Countermeasures: Check the reducer lubricating oil model according to the manufacturer's instructions . Gear oil containing extreme pressure anti-wear additives can be used under heavy-duty conditions; change the oil strictly on a regular basis, and confirm that the new oil is compatible with the old oil before replenishing oil; conduct oil ferrography tests regularly if possible to grasp the wear trend.
4. Assembly bias load: Abnormal meshing contact spots
A considerable part of early pitting corrosion is not a quality problem of the gear itself, but a unilateral load caused by assembly deviation: non-parallel axes, excessive coaxiality, and gear meshing misalignment after bearing wear will cause the load to be concentrated at one end of the tooth width, and the local stress will increase exponentially. After assembly and maintenance, the contact spots should be checked by turning the machine. Hard tooth surface gears require that the tooth height direction be no less than 70%, the tooth width direction be no less than 60%, and the spots should be centered. When the spots are skewed, the bearing seat and shafting must be adjusted, and they must not be operated with disease.
Cheat Sheet of Measures to Prevent Gear Pitting Corrosion
link | measure | Reference points |
|---|---|---|
DesignSelection | Check contact stress and service factor | Amplified usage coefficient for impact conditions; positive displacement reduces sliding coefficient |
Material heat treatment | Carburizing and quenching + gear grinding | Tooth surface 58~62HRC, Ra≤0.8μm |
Lubrication maintenance | Choose the right viscosity and change oil on schedule | Heavy-duty extreme pressure gear oil, water-proof |
Assembly and maintenance | Check contact spots and alignment | Tooth height ≥70%, tooth width ≥60%, centered distribution |
How to judge whether pitting corrosion needs treatment
There are two trends in pitting corrosion: small pittings that appear in the early stages of running-in of gears with soft tooth surfaces often stop developing or even disappear after the contact gradually becomes even. This is convergent pitting corrosion and can continue to be observed and used; while the tooth surface of the reducer with hard tooth surface is hard and brittle. Once pitting corrosion occurs, it will basically only advance and not retreat. It is extended pitting corrosion. If the pittings expand continuously, maintenance and replacement should be arranged. Delay until the gear teeth break will be more costly. Periodic photos can be taken on-site to record the status of the tooth surface and compare the number and area changes of pits.
Conclusion: Pitting corrosion prevention and control should be carried out throughout the entire process of Selection, manufacturing and use.
To sum up, there is no single-point solution to the prevention and control of reducer gear pitting : the design end should calculate sufficient contact stress and reducer service coefficient , the manufacturing end should ensure hardness and gear grinding accuracy, and the use end should ensure good oil quality and assembly quality. All three lines of defense are indispensable. By incorporating tooth surface inspection into regular inspections and early detection and early treatment, most pitting corrosion faults can be solved within controllable costs.
Pitting corrosion maintenance or Selection have questions? Consult Hangzhou Weigao Transmission
Hangzhou Weigao Transmission Machinery Co., Ltd. is a reducer manufacturer specializing in the manufacturing of transmission equipment . Its product lines cover cycloidal pinwheel reducers, hard tooth surface reducers, coaxial reducers, NMRV worm gear reducers and gear reduction motors. The gears all adopt carburizing and quenching and gear grinding processes, and provide technical support such as contact spot inspection, oil quality and fault tooth surface analysis. Send us the equipment model, operating load and tooth surface photos, and you can get free reducer Selection consultation and maintenance suggestions. As based in Hangzhou a Hangzhou reducer manufacturer , we support customized drawings and samples and compare them with imported brand models. Welcome to call us for negotiation.