Analysis and application scenarios of self-locking function of worm gear reducer - Hangzhou Weigao Transmission

Publish Time: 2026-10-13     Origin: Site

In working conditions such as vertical lifting and inclined conveying, where 'accidents will occur if the machine stops unsteadily', engineers often think of using a worm gear reducer to solve the problem. Because it has reverse self-locking capabilities, the load will not slide down on its own after a power outage. However, self-locking is not the default attribute of all worm gear pairs. It is determined by the calculation results of the lead angle, friction coefficient and reducer speed ratio . This article explains the origin, efficiency value and typical application scenarios of self-locking , so that Selection and maintenance personnel can judge when they can rely on it.

1. Where does self-locking come from: The lead angle is less than the equivalent friction angle

The self-locking of worm gear transmission is essentially a game between geometric angle and friction. When the worm is active, the helical tooth surface pushes the worm gear to rotate; when the worm wheel tries to drive the worm in the reverse direction (such as the load sliding due to gravity), the helix angle of the worm tooth surface becomes a slope - the slope is too gentle and the load cannot push it. This helix angle is the lead angle (λ), and the angle required by the friction surface to prevent sliding is called the equivalent friction angle (ρ = arctan μ). The self-locking criterion is therefore very clear: if the lead angle is less than the equivalent friction angle, the mechanism has reverse self-locking.

Taking a steel worm with a bronze worm gear and mineral oil lubrication as an example, the friction coefficient μ is about 0.08 to 0.12, and the corresponding friction angle is about 4.6° to 6.8°; only when the lead angle is within this range, the self-locking function is established. Empirical judgment can be seen in the speed ratio: when it is above 30:1, the lead angle is usually small enough and self-locking is more reliable; when it is below 20:1, the lead angle is too large and must be calculated on a unit-by-unit basis.

2. The trade-off between self-locking and efficiency

The law is straightforward: large speed ratio, high self-locking reliability and high transmission efficiency cannot be achieved at the same time. The smaller the lead angle, the more reliable the self-locking is, but the higher the proportion of sliding friction, the lower The following table shows the experience intervals divided by lead angle, which can be used for quick judgment.the transmission efficiency of the reducer and the more obvious the heat generation.

Lead angle λ

Typical ratio i

Transmission efficiency eta

Self-locking reliability

3°~5°

60:1~100:1

40%~55%

reliable, dependable

6°~8°

30:1~60:1

55%~70%

Reliable in most working conditions

10°~15°

10:1~30:1

70%~82%

Edge, need to be measured

20°~30°

5:1~10:1

83%~92%

Basically no self-locking

The table is the reference value under full load, normal temperature and standard mineral oil conditions. Relying on self-locking in exchange for safety comes at the cost of low efficiency, and continuous operation requires attention to heat dissipation. If the equipment requires high-tempo continuous operation, helical gears or planetary structures are usually used with brakes instead of placing the worm gear in an efficiency-sensitive position.

3. Which occasions are inseparable from the self-locking worm gear reducer?

The value of self-locking is that it can lock the position without additional power. The following four typical situations are:

Vertical lifting and hoisting: electric hoist, elevator reducer , three-dimensional garage lifting platform, etc. When the machine is shut down or suddenly loses power, the load will stop at the original height by self-locking, without the need for continuous power on.
Inclined conveyor and climbing section: When the climbing belt conveyor and inclined screw conveyor are stopped, the material will not drive the conveyor belt to rotate in the opposite direction.
Angle maintaining mechanism: The solar tracking bracket, mold turning table, and valve actuator lock themselves after they are in place, reducing standby energy consumption.
Safety and positioning assistance: machine tool feed, protective door and other occasions where the position is required not to drift after shutdown.

4. Self-locking is not absolute: three types of failure risks

At the scene, be wary of omitting the braking device because you think the self-locking is very stable. The following three situations will greatly compromise the self-locking:

First, the worm gear is worn . After long-term operation, the tooth surface contact area decreases, the roughness increases, and the friction coefficient decreases. There are data records that when the friction coefficient drops from 0.1 to 0.05, the 4° lead angle that originally satisfied self-locking will become invalid. Therefore, regular inspection of the tooth surface and meshing clearance is the basis for maintaining self-locking.
Second, the lubrication state is abnormal. Insufficient viscosity of the oil or mixing of metal shavings and moisture will weaken the bearing capacity and friction of the oil film, and the self-locking will deteriorate. It is critical to select oil according to the working conditions and change the oil periodically. It is generally recommended to change the oil every 2000 to 4000 hours of operation.
Third, impact load. A sudden impact force may instantly overcome the self-locking resistance torque. It is recommended to retain mechanical or electromagnetic braking as double protection for hoisting and human-carrying equipment. The braking torque is usually more than 1.5 times the load torque.

5. Practical points on Selection and maintenance

It is a safer idea to regard self-locking as the bottom line of safety rather than the only insurance. Selection It is recommended to confirm three points in the Selection stage: first, whether reverse drive is required. If the equipment has manual descent or emergency reversal requirements, self-locking will become an obstacle, and an unlocking mechanism needs to be reserved; second, obtain actual measured data of the worm lead angle and efficiency, rather than just infer theoretical parameters; third, in special installation modes such as vertical, confirm whether the oil seal specifications and box oil guide structure have been optimized for this posture to avoid leakage and poor lubrication.

NMRV products have relatively neat specifications, with a square box body, a center distance of 25 to 130, and a wide coverage. They are often used in small and medium power applications with limited space. Only when the load properties, start-stop frequency, ambient temperature and speed ratio are disclosed together can the lead angle and efficiency be accurately calculated and rework can be avoided.

Conclusion: Calculate the lead angle first, and then talk about self-locking

Back to the original question - can the self-locking of The answer depends on the parameters: if the lead angle is less than the equivalent friction angle, the speed ratio is adequate, and the oil quality and wear are controlled, it is a reliable solution that eliminates the need for braking; on the contrary, it is just a gear pair with high friction, and safety depends on the brake. Calculating the worm gear reducer be relied on? the reducer speed ratio and self-locking conditions in advance is more cost-effective and downtime than installing brakes afterwards.

If you need to calculate the self-locking conditions, you are welcome to consult Hangzhou Weigao Transmission

Hangzhou Weigao Transmission Machinery Co., Ltd. is a reducer manufacturer specializing in transmission equipment . Its product line covers cycloidal pinwheel reducers, hard tooth surface reducers, coaxial reducers, NMRV worm gear reducers and gear reduction motors. It can provide speed ratio calculation and self-locking condition confirmation for lifting, hoisting, conveying, mixing and other working conditions, and supports model comparison for old machine replacement. If you have equipment that requires vertical locking or angle maintenance, send us the motor power, input speed, output torque, installation method and load characteristics, and we will provide free reducer Selection consultation and parameter confirmation. As based in Hangzhou a Hangzhou reducer manufacturer , we also welcome drawings and samples for customization and batch supply negotiations.

FEEDBACK

What is the clearance standard of P series planetary reducer under different working conditions?

How to choose the P series planetary reducer suitable for your equipment

How to detect early fracture of ZLYJ173 reducer gear

How to judge the degree of breakage of ZLYJ series reducer gears by listening to the sound

What are the common causes of failure of NGW102-6 planetary reducer bearing components?