Article List
- Steps for correct installation and maintenance of planetary gear motorsThe correct installation and maintenance of the planetary gear motor is the key to the normal operation of the planetary gear motor.Therefore, when you install the planetary gear motor, please be sure to install it strictly according to the following installation sequence.8MM hardware gear box step: Before installation, confirm whether the motor and planetary gear reducer are complete and undamaged, and strictly drive whether the dimensions of the parts connected to the motor and the reducer are aligned.This refers to the dimensions and common tolerances between the positioning boss and shaft diameter of the transmission motor flange and the positioning groove and aperture of the reducer flange; wipe and deal with dirt and burrs on the common surface.Step 2: Unscrew the screw plug on the process hole on the side of the reducer flange, turn the input end of the reducer to align the tightened hexagon socket head screw cap with the process hole, insert the hexagon socket tool to loosen and tighten the hold hexagon socket head screw .Step 3: Hold the transmission motor so that the keyway on the shaft is perpendicular to the tightening screw in the input end hole of the reducer, and insert the drive motor shaft into the input end of the reducer
- How to maintain the small reducer?The small geared motor is a widely used deceleration transmission equipment. The maintenance method of the small geared motor is as follows: 1. Keep the geared motor well lubricated, pay attention to adding gear oil or replacing the gear oil, and there is no dry friction.2. First of all, in terms of external environment, tools, accessories, and workpieces (products) should be placed neatly, and pipes and lines should be organized.Small geared motor.3. Regularly clean all parts of the rotary gear reduction motor. If there are debris, sundries and stolen goods around the reduction motor, the staff should clean them up in time.4. Next, in terms of rules and regulations, the staff who operate the gear reduction motor must abide by the operating procedures, do not use the gear reduction motor with overload, the mechanical protection devices are reliable and complete, and pay attention to timely eliminate unsafe factors.5. Clean the motor reducer.Remove the dust and sludge on the outside of the motor reducer frame in time.If the use environment is dusty, clean it once a day.6. Check and clean the motor reducer wiring
- Comprehensive analysis of damage state of gear reducerEvery company expects high-end product structure to win high-margin stores, but product upgrades must have appropriate soil cooperation, and cultivating this soil is a step-by-step process, especially in gearbox manufacturing: First, high-skilled training needs talents accumulated over the years
- Comprehensive analysis of the damage status of gear reducerEvery company expects a high-end product structure to win high-profit stores, but product upgrades must have proper soil cooperation, and cultivating this soil is a step-by-step process, especially in gearbox manufacturing: first, high-skills Training needs of talents For many years, the accumulatio
- Cycloidal gear reducer conditions1. Allows cycloidal gear reducers to be used in continuous work systems, allowing both forward and reverse directions.2. The rated speed of the input shaft is 1500rpm.When the input power is greater than 18.5 kW, it is recommended to use a 6-pole motor with 960 rpm.3.
- Cycloidal pinwheel reducer conditions1. The cycloidal pinwheel reducer is allowed to be used in the continuous working system, while allowing both forward and reverse directions. 2. The rated speed of the input shaft is 1500 rpm. When the input power is greater than 18.5 kW, it is recommended to use a 6-pole motor with 960 rpm. 3. The
- Frequently asked questions about helical gear reducers1. Heat and oil leakage sequentially improve efficiency, worm gear reducers usually use non-ferrous metals as worm gears, and worms use harder steel.Because it is a sliding friction drive, more heat will be generated during operation, which will cause a difference in thermal expansion between P
- Common problems of helical gear reducer1. Heat and oil leakageIn order to improve efficiency, worm gear reducers generally use non-ferrous metals as worm wheels, and worms use harder steel. Because it is a sliding friction drive, more heat will be generated during operation, which will cause differences in thermal expansion between the p
- Introduce the principle and characteristics of RV reducerThe RV reducer is used for the three joints of the leg, waist and elbow of the high-torque robot.For industrial robots with heavy loads, RVs are used for one, two, and three axes.Compared with the harmonic reducer, the key of the RV reducer lies in the processing technology and assembly process.RV reducer has high fatigue strength, rigidity and service life. Unlike harmonic transmission, the motion accuracy will be significantly reduced as the use time increases. The disadvantage is that it is heavy in weight and large in size.1. The principle of the reducer The worm reducer is a power transmission mechanism that uses the speed converter of the gear to reduce the number of revolutions of the motor (motor) to the desired number of revolutions and obtain a larger torque mechanism.In the mechanism used to transmit power and motion, the application range of the reducer is quite wide.It can be seen in the transmission system of various machinery, from ships, automobiles, locomotives, heavy machinery used in construction, processing machinery and automated production equipment used in the machinery industry, to daily life.
- What are the functional uses of the precision planetary reducer?The output torque of industrial high-precision planetary gear reducer motors generally does not exceed 2,000 Nm, and the special-purpose super-large torque planetary reducer can reach more than 10,000 Nm.The working temperature is generally from -25°C to 100°C.The working temperature can be changed by changing the lubricating grease.High-precision planetary geared motor is a universal reducer.The internal transmission gear is nitrided, heat treated and cut by 20cvmnt.The whole machine has the characteristics of small size, light weight, large output torque, high bearing capacity, long service life, stable operation, low noise, high transmission ratio, high efficiency, and reliability.It is more suitable for lifting and transportation, engineering machinery equipment, metallurgical industry, mining, petrochemical equipment, engineering machinery equipment, light industrial textiles, medical equipment, instrumentation equipment, vehicles, ships, weapons and equipment, aerospace and other industrial sectors.The above are the main components of the high-precision planetary reducer that I introduced to you in detail.