ZDY hard tooth surface reducer and motor connection and debugging steps

Publish Time: 2026-10-13     Origin: Site

1. Preparation and inspection before installation

  1. Check the specifications to
    confirm that the motor model, power, speed, shaft diameter, and flange size are consistent with the input specifications of the ZDY reducer to avoid installation failure or abnormal operation due to mismatch.

  2. Appearance and accessories inspection
    Check whether the reducer and motor housing, flange surface, threaded hole, input shaft, and output shaft are intact, without bumps, deformations, cracks, or thread damage. Check whether bolts, sealing rings, couplings, set screws and other accessories are complete.

  3. Cleaning process:
    Use dust-free rags or alcohol cotton pads to clean the motor flange surface, motor shaft, reducer flange surface, input hole and keyway to remove oil, dust, iron filings and anti-rust oil to ensure that the mating surface is smooth and clean.

  4. Tool preparation
    Prepare standard wrenches, Allen wrenches, torque wrenches, soft percussion tools (such as copper hammers, rubber hammers), feeler gauges or alignment measuring tools, and necessary cleaning supplies.

2. Standard installation steps

  1. Shaft and Key Handling
    Check the motor output shaft dimensions. If the motor shaft diameter is ≤Φ35, the flat key on the motor shaft should be removed first; if the shaft diameter is >Φ35, subsequent installation can be performed directly. If you need to use a bushing, you should first insert the adapter bushing into the input hole of the reducer and make sure it fits tightly and is not loose.

  2. Coupling installation (if applicable)
    When using coupling connection, first fix the coupling halves on the motor output shaft and reducer input shaft respectively, and then connect the two halves of the coupling through elastic pins, diaphragms or other connectors. During installation, the connections should be ensured to be tight and appropriate clearance should be reserved to avoid axial locking.

  3. Motor pre-assembly and
    alignment: Align the motor vertically with the input hole of the reducer or the coupling, and push it in slowly and steadily to ensure that the motor flange and the reducer flange are completely fit. It is strictly prohibited to tilt, forcefully press or knock the flange to prevent shaft deformation, seal damage or bearing damage. The coaxiality error should be controlled within the allowable range, and it is generally recommended to be ≤0.03mm.

  4. Flange bolt pre-tightening
    : Pre-tighten the flange outer hexagonal bolts in diagonal order. The pre-tightening torque can be set to about 50% of the specified torque. It is only used for preliminary fixation to prevent uneven stress on the flange.

  5. Locking with a tightening ring or locking device
    . If the input end of the reducer is equipped with a tightening ring, clamping ring or other locking device, a torque wrench should be used to cross-lock twice according to the specified torque to ensure that there is no relative displacement between the motor shaft and the input hole of the reducer.

  6. The flange bolts are finally locked
    in diagonal order again, and the flange outer hexagonal bolts are fully tightened to the specified torque. After tightening, check whether each bolt is in place to avoid leakage or over-tightening.

  7. Manual turning inspection
    After the installation is completed, manually turn the motor shaft 3 to 5 times. There should be no stagnation, friction or eccentric shaking during the rotation process, and the turning resistance should be uniform. If stuck or abnormality occurs, the coaxiality should be recalibrated, and forced power on is prohibited.

3. Trial operation and inspection

  1. No-load test run
    After confirming that the installation is correct, power on and conduct a no-load test run for 3 to 5 minutes. Observe whether the equipment is running smoothly and check for obvious vibration, abnormal noise, abnormal temperature rise or oil leakage. The surface temperature of the reducer should generally be kept within the normal range, and it is recommended not to exceed 45°C under no-load conditions.

  2. After the load test runs and
    the no-load operation is normal, gradually load it to the rated load and run continuously for about 30 minutes. Check the equipment operating status, vibration amplitude, noise and temperature rise again. After confirming that there are no abnormalities, it can be put into formal use.

4. Safety and maintenance precautions

  1. Power-off operation
    During installation, commissioning and maintenance, the power supply must be cut off, and live work is prohibited to prevent personal injury and equipment damage.

  2. Violent installation is prohibited
    and direct knocking of the motor or reducer body is prohibited. If you need to fine-tune the position, tap lightly with a soft tool and make sure the force is applied in the correct direction.

  3. Regular inspection and maintenance
    After the equipment is in operation, the tightening status of the flange bolts and tightening ring bolts should be regularly checked to prevent loosening due to vibration. At the same time, check whether there is leakage in the sealing ring, oil seal and joint surface. If any abnormality is found, deal with it in time.

  4. According to the manufacturer's requirements,
    the bolt torque, alignment requirements and locking methods of different models of ZDY reducers may be different. The actual installation should be based on the product manual or the manufacturer's technical data.

FEEDBACK

What are the maintenance points for ZDY250-3.55-II hard tooth surface reducer in food plants?

How to perform daily inspection of the sealing system of ZDY315-4.5-I hardened reducer?

What is the clearance standard of P series planetary reducer under different working conditions?

How to choose the P series planetary reducer suitable for your equipment

How to detect early fracture of ZLYJ173 reducer gear