Six major causes of reducer bearing heating and on-site countermeasures-Hangzhou Weigao Transmission
Publish Time: 2026-10-13 Origin: Site
During on-site inspections, hot spots on the bearings of the reducer are one of the phenomena with high frequency of repair requests. There is no unified red line for bearing temperature, but if the operating temperature suddenly rises 15 to 20°C higher than usual, or the shell temperature exceeds 90°C for a long time, you must stop and investigate the cause, otherwise it may lead to cage cracking, raceway peeling or even shaft locking. Most of the causes of reducer heating are not in the bearing itself, but in the three links of lubrication, assembly and load. This article sorts out the six major causes according to frequency of occurrence, and gives corresponding on-site disposal methods for reference by maintenance and inspection personnel.
1. Lubrication problems: Wrong quantity and oil deterioration account for the majority.
According to statistics of on-site cases, more than half of bearing overheating is related to lubrication, but in the opposite direction - first, insufficient oil : the oil level is lower than the lower edge of the rolling elements, the oil film cannot be established, and dry friction generates heat; second, too much oil : the rolling elements repeatedly stir the oil, and the resistance increases but heats up, especially when installed vertically; third, the oil deteriorates : after oxidation, emulsification or mixing with metal shavings, the bearing capacity of the oil film decreases. Disposal points: Check whether the reducer lubricating oil model is consistent with the manufacturer's requirements. The oil level is controlled near the center line of the oil mark. When the bearing chamber is lubricated with grease, the filling amount should be 1/2 to 2/3 of the bearing chamber volume. Overfilling will be harmful. Deteriorated oil must be thoroughly rinsed and replaced with new one.
2. Improper fit tolerance: too tight or too loose will cause heat
The coordination between the bearing inner ring and the shaft, the outer ring and the end cover hole is a matter of precision. When the fit interference is too large, the clearance will be squeezed out after assembly, and the rotational resistance and temperature rise will rise simultaneously; when the fit is too loose, relative creep (creep) will occur between the inner ring and the shaft, causing friction and heat and wear of the journal. On-site judgment: During disassembly and inspection, check whether there are circumferential wear marks (signs of creep) on the end face of the inner ring, and measure whether the journal size has been reduced. The countermeasure is to repair the journal or replace the bearing according to the drawing tolerance. You cannot make do by making pits or adding gaskets.
3. The clearance disappears: The thermal expansion eats up the clearance
Residual clearance after bearing installation is less than the working clearance required for operation is another common source of overheating. There are three reasons: the interference eats up the original clearance; there is no reserved clearance for the axial movement of the shaft after it is heated and stretched (an axial clearance of about 0.2~0.4mm should be left at the outer ring end cover, and the visual axis length and temperature rise are adjusted); Selection, the clearance group is selected to be small. Countermeasures: Measure the remaining clearance during maintenance, switch to a large clearance group (such as C3/C4) if necessary, and leave a thermal expansion gap between the end cover and the bearing outer ring.
4. Installation deviation and improper preloading
If the end caps or bearing seats at both ends are installed misaligned or not parallel, the rolling elements will run out of the raceway, causing heat and noise in a short period of time; excessive preload (such as improper grinding of diagonal angular contact bearing pads) will also cause significant temperature rise. Countermeasures: When reassembling, ensure that the seams are close and the bolts are tightened diagonally evenly; use a dial indicator to check the rotation resistance and axial movement of the shaft, and make sure it meets the drawing requirements before putting it into operation.
5. Abnormal external load: the bearing is responsible for other faults
Bearing heating is sometimes a 'scapegoat': poor with the motor alignment of the coupling will add periodic radial force to the bearing; belts and chains are too tight, and the cantilever load exceeds the design value; after the shaft itself is bent, the bearing no longer bears pure radial force. This type of heating is often accompanied by an increase in vibration levels. Countermeasures: First use a vibration meter to locate the vibration source, check the alignment deviation (rigid couplings are generally controlled within 0.05mm), the belt tension and the straightness of the shaft, eliminate the source of external load, and the bearing temperature will tend to naturally drop.
6. Damage to the bearing body: it must be replaced at the end of its life
Damage to the cage, pitting and peeling of the raceway, and indentation of the rolling elements will all cause a sudden increase in friction power. The auscultation characteristic is that the sound of 'rustling' changes to 'thumping', and the energy at the characteristic frequency of the bearing on the frequency spectrum increases significantly. At this time, you should no longer rely on oil replenishment, but should arrange for the replacement of the reducer bearings : record the original bearing model, clearance group and manufacturer, heat and install the new bearing (heat the induction heater to 90~110°C, open flames and hammering are strictly prohibited), and test the temperature again for 30 minutes without load after installation.
On-site quick judgment reference table
temperature performance | Common directions | primary action |
|---|---|---|
Temperature rises quickly just after changing oil | The oil level is too high or the oil type is wrong. | Drain oil to the calibrated oil level and check the oil quality |
Temperature gradually rises, accompanied by noise | Lubrication failure or bearing wear | Sampling and testing of oil, auscultation and examination |
High temperature and large vibration | Poor alignment and abnormal external load | Measure vibration and review coupling alignment |
New machine overheats when put into operation | Improper assembly clearance/preload | Shutdown, measured clearance, reinstallation |
When the ambient temperature is high, the temperature is higher | Insufficient cooling | Improve ventilation and clean dust accumulated on cooling ribs |
Daily maintenance of the reducer should be done first - regularly check the oil level and oil quality, record the temperature baseline of each measuring point, and change the oil every 2000 to 4000 hours. Most overheating problems can be discovered in the budding stage. When a systematic reducer maintenance plan is needed, it is recommended to make a judgment based on vibration and oil detection data to avoid blind disassembly of the machine.
Conclusion: Check lubrication and assembly first, then look at the bearing itself
Looking back at these six major reasons, the order of troubleshooting the reducer bearing heating should be: first check the oil level and oil quality, then check the fit and clearance, then check the alignment and external load, and finally disassemble and inspect the bearing body. If the order is correct, the downtime will be the shortest; if the order is reversed, the bearings will often heat up again within a few days of replacing them with new ones. By keeping records of the temperature, oil samples and treatment of each overheating, you can find out the 'temperature' of the equipment after a few rounds, and the inspection will be more targeted.
Are you having trouble troubleshooting bearing overheating? Welcome to consult Hangzhou Weigao Transmission
Hangzhou Weigao Transmission Machinery Co., Ltd. is a reducer manufacturer specializing in transmission equipment . Its product line covers cycloidal pinwheel reducers, hard tooth surface reducers, coaxial reducers, NMRV worm gear reducers and gear reduction motors. It can provide customers with bearing configuration and clearance group selection suggestions, remote troubleshooting guidance for overheating faults, and supply of maintenance spare parts. Send us the reducer model, installation method, operating temperature and on-site phenomena, and you can get free reducer Selection consultation and fault analysis. As based in Hangzhou a Hangzhou reducer manufacturer , we support customized drawings and samples to compare with old machine models. Welcome to call us for discussion.