Low-temperature start-up and lubricant selection of reducer in winter: Guide to low-temperature grease and oil change timing - Hangzhou Weigao Transmission

Publish Time: 2026-10-14     Origin: Site

Why is low temperature a "hump" for reducer lubrication?

After winter, the number of reducers reported for repair in northern open-air equipment and low-temperature workshops has increased significantly. The root causes of most failures point to the same link - reducer lubrication . For gear oil with good fluidity at normal temperature, the viscosity will increase exponentially when it reaches more than ten degrees below zero, and the oil film will slow down and the oil pump will have difficulty in absorbing oil; in severe cases, the oil will thicken, and the gear and bearing will be in a state of near-dry friction at the moment of startup. Tooth surface gluing, pitting, and bearing jamming often occur in the first few dozen seconds of cold engine startup. Low temperatures will also cause nitrile rubber seals to harden and lose elasticity, and metal fitting gaps to shrink, simultaneously increasing the risk of oil leakage and jamming. Therefore, the focus of reducer maintenance in winter is not 'add more oil', but to choose the right oil and control the startup process.

Select viscosity according to ambient temperature: correspondence between reducer lubricant models

Oil selection can be divided into two steps: first determine the ISO VG viscosity grade according to the ambient temperature, and then determine the oil type according to the working conditions. Commonly used correspondences are as follows:

ambient temperature range

Recommended viscosity grade

Oil type

SelectionKey points

0℃ ~ -10℃

ISO VG 150 ~ 220

Low pour point mineral/semi-synthetic gear oil

Taking into account low-temperature fluidity and load-bearing capacity

-10℃ ~ -20℃

ISO VG 100 ~ 150

PAO synthetic gear oil

The pour point should be more than 10℃ lower than the ambient temperature

-20℃ ~ -35℃

ISO VG 68 ~ 100

Synthetic/ester gear oil

Recommended viscosity index ≥140, low cold start resistance

Below -35℃

ISO VG 32 ~ 68

Fully synthetic low temperature gear oil

Must be used with preheating device

It should be noted that the 'viscosity reduction' cannot be excessive: too low a viscosity will result in insufficient oil film strength under heavy load conditions, which will in turn accelerate tooth surface wear. Use VG320/VG460 hard-tooth surface reducer at normal temperature . In low-temperature scenarios, it is generally sufficient to lower the speed by one or two gears. Mineral oil is suitable for environments above 0℃. Synthetic oil is more expensive but has significantly better low-temperature fluidity. The worm gear reducer has a steel-copper friction pair. Special worm gear oil or PAG synthetic oil should be selected, and extreme pressure additives containing active sulfur should be avoided to avoid corrosion of the copper worm gear.

Grease lubrication models: How to choose low-temperature grease

Grease lubrication is commonly used for small cycloidal pinwheel reducers and gear reduction motors that are vertically installed, sealed and maintenance-free or difficult to fill with oil. In winter, there are three factors to consider when choosing grease: the consistency grade is recommended to be NLGI No. 00 or No. 0 semi-fluid grease, and the base oil viscosity is ISO VG 100~150; in terms of base oil type, ordinary lithium-based grease will become significantly harder below -20°C, so it should be replaced with synthetic low-temperature grease (lithium-based composite or polyurea thickened, PAO Base oil), the lower limit of use can reach -40℃; at the same time, check the dropping point and operating temperature range to avoid the loss of fat body during operation. Grease-lubricated machines should be opened and inspected before winter. The grease becomes hard and black and needs to be replaced in time. Otherwise, the oil stirring resistance will increase sharply, which will cause the motor to trip due to overload.

Six steps for starting at low temperatures in winter

  • 1. Pre-start inspection. Confirm the oil level, oil quality and sealing status; when the oil shrinks at low temperatures, the oil level will be lower than the standard line. It should be filled to a position slightly higher than the center line of the oil mark, but not too full, otherwise the oil will be stirred and heated.

  • 2. Preheat if necessary. When the ambient temperature is lower than -10°C, use the built-in heating rod or the electric heating tape of the shell to raise the oil temperature to 0~10°C before starting. The upper limit of temperature control is recommended not to exceed 40°C. For small equipment, the shell can be wrapped with a heating blanket and manually turned every 10 minutes.

  • 3. Manual turning. Turn the car 2 to 3 times to confirm that there is no sticking, and at the same time allow the oil to be distributed to the meshing surface.

  • 4. No-load warm-up. No-load operation for 5 to 10 minutes in an environment of 0℃ ~ -10℃; extend to 15 to 30 minutes below -10℃ until the oil temperature rises and the lubrication cycle is established.

  • 5. Hierarchical loading. Add load in steps of about 30%, 60%, and 100%. It is strictly forbidden to start the cold machine directly with full load or with impact load; it should not start and stop more than 3 times per hour.

  • 6. Operation monitoring. Pay attention to the temperature rise and abnormal noise within 30 minutes after starting. The temperature rise should be controlled within 20°C. If there is a sharp friction sound or a sudden increase in vibration, the machine should be stopped immediately for investigation.

Oil change and checklist before winter

Instead of waiting for a breakdown to be repaired, it is better to do a few things before winter: replace the reducer lubricating oil type suitable for low temperature , change the oil when the equipment is hot, drain the old oil and flush the box with a small amount of new oil, do not mix different base oils; replace the nitrile rubber parts of the input and output shaft oil seals with Use low-temperature resistant fluororubber or silicone rubber; retighten the shell and anchor bolts according to the manufacturer's torque; shorten the oil inspection cycle from once a quarter to once a month, focusing on fluidity, color and whether it is emulsified and contains water; after shutdown, the temperature difference is large and it is easy for condensation to form, so the condensed water should be discharged regularly and the ventilation cap should be checked to see if it is blocked by ice.

Conclusion: The answer to low-temperature working conditions lies in both oil selection and process.

Most reducer failures in winter are not 'worn out', but rather that the reducer's lubrication fails to keep up with temperature changes and the startup process is not controlled. By aligning the viscosity grade, oil type and preheating load, most cold start failures can be avoided in advance. If you are making a reducer for a cold area project Selection , or need to match low-temperature oil and seal solutions for existing equipment, please contact Hangzhou Weigao Transmission - the product line covers cycloidal pinwheels, hardened cylindrical gears, worm gears, planetary and coaxial series. As a reducer manufacturer and Hangzhou reducer manufacturer , Weigao Transmission can provide free calculations, oil recommendations and quotation services based on on-site ambient temperature and working condition parameters. We support customization with drawings and samples. Engineers can be available at 24 A complete Selection plan will be issued within hours.

FEEDBACK

Wastewater Treatment Gearbox Market 2027: Policy Deadlines and Screw Pump Sizing

How to calculate the fatigue life of reducer gears: GB/T 3480.6 Variable load Miner damage accumulation calculation example - Hangzhou Weigao Transmission

Vertical Turbine Pump Gear Drive Selection: Thrust Load, Support and Bearing Life

How to determine the shaft diameter and key of the reducer output shaft: shaft diameter estimation, bending and torsion combined strength and flat key connection calculation examples - Hangzhou Weigao Transmission

How to quickly solve the leakage of ZQD1000-317 reducer box