How to determine the shaft diameter and key of the reducer output shaft: shaft diameter estimation, bending and torsion combined strength and flat key connection calculation examples - Hangzhou Weigao Transmission

Publish Time: 2026-11-07     Origin: Site

The reducer sample is marked with a rated output torque, but whether the output shaft can really deliver this torque to the load depends on two things: whether the shaft itself is strong enough and whether the key connection on the shaft is sufficient. These two parts are static connectors. The samples are usually not marked, and the entire section is left blank in the technical agreement. It is not until the day of assembly that a problem occurs in the keyway. Shaft diameter estimation is a common method for mechanical design, and there is also a ready-made formula for key connection strength check. Putting the two together, the three numbers of the output shaft can be determined at the Selection stage: shaft diameter, key cross-sectional specifications, and key length. This article goes through the process according to GB/T 1095-2003 "Sectional Dimensions of Flat Key Keyway", GB/T 1096-2003 "Ordinary Flat Key" and GB/T 2822-2005 "Standard Dimensions", and uses a 7.5 kW two-stage reducer to calculate the value of each step.

1. Three checks that the output shaft must pass

1.1 Three numbers determine the axes, and the other three numbers determine the keys.

The shaft diameter is not found by looking up the table, but calculated: 0 it is determined by the transmission power P, shaft speed n and material coefficient A. The formula d ≥ A 0· (P/n) 1/3 , for 45 steel, take A 0 = 105~120. The key is another three numbers: the shaft diameter d, the cross section of the key b×h, and the working length of the key l. The division of labor among the three verifications is as follows.

step

Check content

input parameters

Calculation formula

output

1

Shaft diameter estimation

P,n,A0

d≥A 0·(P/n) 1/3

Initial value of shaft diameter

2

Resulting strength in bending and torsion

M, T, α, W

σ e = √(M²+(αT)²)/W ≤ [σ -1]

Shaft safety factor

3

key connection extrusion

T, d, h, l

σ p = 4T/(d·h·l) ≤ [σ p ]

Minimum bond length

The three paths are in a series relationship: the shaft diameter determined in the previous step determines the section modulus W in the next step, and the shaft diameter in the second step determines the size of the key that can be selected in the third step. If any step fails, the counting of the following steps must be repeated, so the order cannot be reversed.

1.2 Keyway weakening: the estimated value needs to be enlarged

A keyway was opened on the shaft, a piece of the cross section was cut off, and there was an extra stress concentration, so the estimated shaft diameter could not be used directly. Commonly used corrections in engineering are to enlarge single keyway by 5% and double keyway by 10%. According to HF Moore's keyway weakening relationship e = 1 − 0.2·(b/d) − 1.1·(t 1/d) and substituted into this example d = 56 mm, b = 16 mm, shaft groove depth t 1 = 6.0 mm, we get e = 0.825, which is close to the empirical value of 'Shaft with keyway is calculated as 75% solid shaft'. When converted into shaft diameter, it is about 1.07 times larger, which is equivalent to 5% corrections are of the same magnitude.

2. Calculation example: 7.5 kW two-stage reducer output shaft

2.1 Working conditions and final gear

The calculation example takes a two-stage spur-tooth cylindrical gear reducer . The final output shaft is equipped with both the final gear and the extended pulley. All parameters are listed to facilitate item-by-item replacement.

project

symbol

value

unit

illustrate

Motor power

P1

7.5

kW

Study settings

Motor speed

n1

1 450

r/min

4 pole asynchronous motor

Overall speed ratio

i

20 (4×5 two levels)

—

Typical configuration of two-stage hard tooth surface reducer

total efficiency

η

0.96

—

The measured range of two-stage cylindrical gears is 0.95~0.97

Output speed

n2

72.5

r/min

n 1 /i

Output torque

T2

948.4

N·m

T 2 = 9550·P 1·i·η/n1

final gear

m/z 2 /d2

5/50/250

mm/teeth/mm

Straight teeth, tooth width 50 mm, pressure angle 20°

gear circular force

f​

7 587

N

F t = 2·T 2 /d2

Gear radial force

f​

2 762

N

F r = F t ·tan20°

Support span

L

200

mm

The gear is located at the midpoint of the two support spans

Gear hub width

B

90

mm

Determine the upper limit of key length

2.2 Shaft diameter estimation and rounding

Take A 0 = 110, d 0 = 110 × (7.2/72.5) 1/3 = 50.9 mm ; considering the single keyway weakening and enlarging it by 5%, we get 53.5 mm. According to GB/T 2822-2005 'Standard Dimensions', the R20 series is preferred and rounded upward to obtain d = 56 mm . Then according to GB/T 1095-2003, check the corresponding keyway section for a shaft diameter of 56 mm: b×h = 16×10, shaft groove depth t 1 = 6.0 mm, hub groove depth t 2 = 4.3 mm, t 1 + t 2 − h = 0.3 mm, which is the gap amount between the key top and the hub groove bottom.

2.3 Check of the resultant bending and torsion strength

The output shaft is a typical bending-torsion combined stress shaft, which is checked according to the third strength theory. At the midpoint of the span of the gear, the bending moments in the two directions are M V = F t ·L/4 = 379 366 N·mm, M H = F r ·L/4 = 138 078 N·mm, and the resultant bending moment M = √(M V ² + M H ²) = 403 712 N·mm. The torque is converted according to the pulsation coefficient α = 0.6.

project

symbol

numerical value

unit

illustrate

Vertical plane bending moment

M V

379 366

N·mm

Produced by gear circumferential force

Horizontal plane bending moment

M H

138 078

N·mm

Produced by gear radial force

Resultant bending moment

M

403 712

N·mm

vector composition

Torque

T

948 414

N·mm

T 2×1000

Conversion factor

α

0.6

—

Torque ripple, frequent forward and reverse rotation takes 1.0

Equivalent bending moment

M e

697 710

N·mm

√(M²+(αT)²)

Bending section modulus

W

17 241

mm³

π·d³/32

equivalent stress

σ e

40.5

MPa

M e / W

allowable stress

[σ -1]

60

MPa

45 steel tempered

safety factor

S

1.48

—

[σ -1]/σ e

Here is a comparison that is easy to skip: Calculating only based on pure twist, τ = 16T/(πd³) = 27.5 MPa, which seems to be a large margin; after the bending moment is included, the equivalent stress rises to 40.5 MPa, which is amplified by 1.47 times. Shaft diameter is estimated by torque, and bending moment is its actual examiner.

2.4 Key connection strength check

The extrusion strength of the bond is checked according to σ p = 4T/(d·h·l) ≤ [σ p ], where l is the working length of the bond, not the total length of the bond. For the mild impact condition of steel parts, [σ p ] = 100~120 MPa, and the allowable shear stress [τ] = 90 MPa.

3. Bond type and bond length: How to choose among the four options

3.1 The working lengths of types A, B, and C are slightly different.

For the same key marked L = 80 mm, the working lengths of the three types are completely different: type A (round head) l = L − b = 64 mm, type B (square head) l = L = 80 mm, and type C (single round head) l = L − b/2 = 72 mm. The load-carrying capacity difference between Type A and Type B is 25%, so Selection cannot only be based on the marked length ratio.

3.2 Comparison of four options

plan

Working length l (mm)

Compression stress σ p (MPa)

Extrusion safety factor

Shear stress τ (MPa)

in conclusion

Type A 16×10×70

54

125.5

0.80~0.96

39.2

Extrusion failed

Type A 16×10×80

64

105.8

0.94~1.13

33.1

Critical, impact conditions are tight

Type B 16×10×80

80

84.7

1.18~1.42

26.5

Available in mid-shaft

Type C16×10×80

72

94.1

1.06~1.28

29.4

The shaft end is available and the margin is average

The shear strengths of the four schemes are all between 26 and 39 MPa, which is more than 2 times the margin relative to [τ] = 90 MPa. The conclusion is clear: ordinary flat key connections are controlled by extrusion strength, and shear strength is not a controlling condition , so the verification focus should be on the bond length.

3.3 Back calculation, double bond and two calibers

It is more practical to work backward from the results. Back calculation according to [σ p ] = 100 MPa, l needs to be ≥ 67.7 mm, the total length of type A key needs to be ≥ 83.7 mm, take 90 mm of the GB/T 1096-2003 length series, and the wheel hub width should be set to 95~100 mm accordingly. If the wheel hub is only 90 mm and A-type keys are to be installed, the double keys can be arranged with a 180° offset. After counting 1.5 keys, σ p = 83.6 MPa, and the safety factor is 1.20~1.43, which is up to standard.

I would also like to remind you of a caliber issue: the textbook formula assumes that the contact height between the key and the hub groove is approximately h/2 = 5 mm. However, based on the actual contact height k = h − t 1 = 4 mm given in GB/T 1095-2003, σ p = 2T/(d·k·l) will be 1.25 times higher than the textbook formula. Recalculating using strict calibers, type B 16×10×80 is 105.8 MPa, and type A 16×10×80 is 132.3 MPa. The output end of the cycloidal pinwheel reducer has a pin and spline structure, and does not require flat key verification; the output shaft of the worm gear reducer is also connected with a key, but the shaft diameter is restricted by the size of the worm gear. When Selection, this set of procedures should be checked at the same time as the rated torque of the sample.

4. Four steps of on-site inspection

step

action

criterion or output

1

Take the actual output torque T and output speed n, and confirm the terminal installation form (pulley, sprocket, gear)

For the cantilever member, first calculate M = F·e

2

Estimate the shaft diameter according to A 0·(P/n) 1/3 , and round the keyway according to GB/T 2822-2005 after weakening and enlarging it.

Shaft diameter d corresponds to b×h in GB/T 1095-2003

3

Calculate M V and M H , and check the axis according to the third strength theory after synthesis

σ e ≤ [σ -1]

4

Determine the key length and key type according to the wheel hub width, check the extrusion, and double-key if necessary

σ p = 4T/(d·h·l) ≤ [σ p ]

Two on-site details deserve their own column. First, when the output end is extended with a pulley, the cantilever moment must be calculated separately: F t = 7 587 N. When the cantilever is 100 mm, F t ·e = 758 700 N·mm, which is close to twice the resultant bending moment of the mid-span gear 403 712 N·mm. At this time, the shaft diameter is mainly determined by the cantilever bending moment, but the key length does not change. The two points must be checked separately. Secondly, when the gear reduction motor is supplied as a whole, the key connection between the motor shaft and the input shaft of the reducer is often designed according to the motor side shaft diameter. Although the input end torque is small, the cross section of the key is locked by the motor standard shaft diameter. Selection The motor model must be confirmed in reverse.

in conclusion

The three numbers of the output shaft can be calculated and should not be left blank. The shaft diameter is estimated according to d ≥ A 0· (P/n) 1/3 , the keyway is weakened and enlarged and rounded according to GB/T 2822-2005, the strength of the shaft is checked according to bending and torsion synthesis, the strength of the key is checked according to GB/T 1095-2003 and GB/T 1096-2003 Selection and extrusion is checked. The conclusion of the calculation example in this article is: the output shaft of the two-stage reducer with 7.5 kW and i = 20 is d = 56 mm, the equivalent stress of the shaft is 40.5 MPa, and the safety factor is 1.48. When the key is B type 16×10×80, σ p = 84.7 MPa, and the safety factor is 1.18~1.42; if the hub width is only 90 mm and A-type keys must be used, the double-key arrangement should be changed. Weigao Transmission provides product lines such as hard tooth surface reducers, cycloidal pinwheel reducers, worm gear reducers and gear reduction motors, and can review the output shaft and key connection according to actual measured working conditions.

FEEDBACK

Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand

How to check the carrying capacity of worm gear reducer: working condition coefficient, efficiency and Selection calculation example - Hangzhou Weigao Transmission

Lubrication and maintenance characteristics of B series industrial gearboxes

What are the common misunderstandings in B series gearbox maintenance?

Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor