How to choose the protection level and insulation level of gear reduction motor: IP code, insulation temperature resistance and working conditions matching - Hangzhou Weigao Transmission

Publish Time: 2026-10-18     Origin: Site

How to choose the protection level and insulation level of gear reduction motor: IP code, insulation temperature resistance and working conditions match

When choosing a gear reduction motor, most users first look at the power, speed ratio and output torque, but easily ignore two parameters that directly determine the service life: protection level and insulation level . Dust intrusion will wear the bearings and degrade the lubricating oil. Moisture penetration will cause winding short circuits. Insufficient insulation temperature resistance will lead to inter-turn breakdown. This article explains step by step how to read the IP code according to the working conditions, the temperature resistance of each insulation level, and how to match it in different environments, for reference during equipment installation and modification.

Protection level of gear reduction motor: How to read the IP code

The protection level is based on the IEC 60529 standard (corresponding to GB/T 4208) and is written as IP + two digits : the first digit indicates the ability to prevent solid intrusion (5=dustproof, allowing a small amount of dust to enter but does not affect operation; 6=completely dust-tight), and the second digit indicates the waterproof ability (4=splash-proof, 5=water spray-proof, 6=strong water spray-proof, 7=can be immersed in water for a short time). Take the most common IP55 as an example: the first '5' means dustproof, and the second '5' means it can withstand water spray from all directions.

It should be noted that the higher the IP level, the stronger the sealing, but the heat dissipation capacity may decrease. Therefore, higher is not better, but it must match the actual working conditions. This is also the core content of the environmental verification link in the reducer Selection .

How to choose the protection level of gear reduction motor: comparison of typical working conditions

Based on common industry practices, the recommended protection levels of gear reduction motors in different environments are as follows:

Working environment

Typical scenario

Recommended protection level

Supporting measures

Indoor cleaning workshop

Warehousing lines, indoor conveyors

IP54~IP55

Standard double lip oil seal

Light dust workshop

Packaging machine reduction motor , woodworking equipment

IP55

Clean cooling air ducts regularly

Heavy dust workshop

Feed, stone, metallurgical ingredients

IP65

The output shaft is equipped with a dustproof sheath and the box seal is thickened.

Open air or risk of being exposed to rain

Outdoor conveyor corridors and open-air storage yards

IP65 and above

Install rainproof cover and outlet box waterproof connector

Washing and food environment

Food machinery reducer , beverage filling line

IP66~IP67

Stainless steel output shaft, anti-corrosion coating, EPDM temperature-resistant oil seal

For situations where the reducer is installed vertically or with the flange facing upward, the junction box and oil seal are more likely to accumulate water and dust. The protection level should be one level higher than that of conventional horizontal installation. At the same time, pay attention to calibrating the oil injection amount according to the oil level mirror scale.

Insulation level and temperature resistance: the difference between Class B, Class F and Class H

The insulation level indicates the heat resistance of the motor winding insulation material. Three levels are commonly used:

Insulation level

Extreme temperature resistance

Winding temperature rise limit (resistance method)

Applicable instructions

Class B

130℃

80K

Under light load intermittent conditions, it is rarely used now.

Class F

155℃

105K

Industry common grade, used with temperature rise margin

Class H

180℃

125K

High temperature workshop, frequent start and stop, frequency conversion matching

The key to Selection is to leave a margin for 'ambient temperature + temperature rise': when the environment is 40°C and the temperature rise is 105K in Class F, the actual temperature of the winding is close to 145°C. If the heat dissipation is poor or overloaded for a long time, it will trigger the most typical winding overheating problem among the A common practice is to insulate according to Class F and conduct temperature rise assessment according to Class B (that is, 'Leave a margin for Class F assessment'), so that the insulation life can be guaranteed even if the load fluctuates. In situations with frequent starts and stops, forward and reverse rotation, or operation with a frequency converter, it is recommended to directly use F-level or above insulation and use an independent cooling fan.reducer heating causes .

Details of working conditions beyond protection and insulation

  • Oil seals and seals : A high IP rating depends on the quality of the oil seal. In outdoor and high-temperature situations, oil seals made of fluorine rubber or EPDM should be used to avoid aging and failure of ordinary nitrile oil seals.

  • Low temperature start : When the environment is lower than -10℃, it is necessary to replace the low temperature grease and preheat the motor, otherwise the starting torque will increase sharply.

  • Variable frequency operation : During variable frequency power supply, the windings are subject to high-frequency voltage impacts, and the insulation system should be a dedicated electromagnetic wire for variable frequency motors.

  • Daily inspection : Incorporate sealing status and temperature rise into routine maintenance items of the reducer , record oil temperature and winding temperature every month, and investigate abnormal temperature rise trends in a timely manner.

Conclusion: Match according to working conditions, not by parameters.

To sum up: the protection level of the gear reduction motor depends on 'water and dust', and the insulation level depends on 'heat and ambient temperature'. The two together determine the life of the equipment under real working conditions. IP55+F grade insulation under normal indoor working conditions can cover most scenarios; heavy dust, open air and water-washed food environments need to be upgraded accordingly. If you are not sure which gear configuration corresponds to the working condition in Selection, please contact Hangzhou Weigao Transmission : As a professional Hangzhou reducer manufacturer , the company provides a full range of products such as cycloid pinwheel reducers, hardened cylindrical gear reducers, worm gear reducers and gear reduction motors. We can provide free reducer Selection consultation and customized solutions according to your installation size, load and environmental conditions.

FEEDBACK

What are the maintenance points for ZDY250-3.55-II hard tooth surface reducer in food plants?

How to perform daily inspection of the sealing system of ZDY315-4.5-I hardened reducer?

What is the clearance standard of P series planetary reducer under different working conditions?

How to choose the P series planetary reducer suitable for your equipment

How to detect early fracture of ZLYJ173 reducer gear