How to choose between cycloid reducer and planetary reducer: comparison of structure, backlash, efficiency and application - Hangzhou Weigao Transmission

Publish Time: 2026-10-21     Origin: Site

Cycloidal pinwheel reducer and planetary reducer: two technical routes for coaxial transmission

The same 'coaxial arrangement, flange installation, with servo or ordinary motor', cycloidal pinwheel reducer and planetary reducer are often put into the same inquiry list for comparison. The two have similar appearances and overlapping speed ratio gears, but the internal structures are completely different, and the performance boundaries are also clearly defined: one relies on multi-tooth meshing to resist impact and carry large speed ratios, while the other relies on multiple wheels to share the load for accuracy and response. If you can't distinguish between these two technical routes, the common result is that you either pay more for unused accuracy, or the planetary machine suffers from pitting after using it in impact conditions for two or three months. This article from the five dimensions of principle, compares the two types of models 、reducer transmission efficiency , reducer backlash , load-bearing capacity, and lifespan, and provides a method for matching seats according to working conditions.

Different transmission principles: small tooth difference meshing and planetary gear train

The cycloidal pinwheel reducer adopts the KHV small-tooth-difference planetary transmission principle: the eccentric shaft at the input end drives the cycloid wheel, which meshes with the pin tooth pin on the pinion gear housing, and uses the difference of 1 to 2 teeth to achieve a large reduction ratio output. Its structural feature is the large number of meshing teeth - theoretically, about half of the teeth are in contact at the same time, and the load is distributed to a large number of tooth surfaces, which is the source of its impact resistance. The main moving parts are only the cycloid wheel, pin tooth pin and output mechanism. The box body is mostly integral, and the axial size is 30% to 40% shorter than the planetary machine of the same power.

The planetary reducer consists of a sun gear, a planet gear and an internal ring gear to form a classic planetary gear train. Usually 2 to 3 planet gears are arranged symmetrically and share the load synchronously. Power is input through the sun gear and output by the planet carrier. Multiple pairs of gear pairs mesh at the same time, resulting in smooth operation and low noise. Most of them adopt modular design, and the gear components can be replaced individually. Due to structural differences, the two have different advantages in speed ratio, accuracy and load-bearing capacity.

Comparison of reducer transmission efficiency and speed ratio range

Speed ​​ratio and efficiency are the first two sets of numbers to look at when Selection. The single-stage speed ratio of the cycloid machine is much wider than that of the planetary machine. There is no need to connect multiple stages in series when the speed ratio is large. The efficiency of the planetary machine decreases with the number of stages, and the gap widens after multi-stage superposition.

project

Cycloid pin wheel reducer

Planetary reducer

Single speed ratio

9~87

3~10

multi-speed ratio

Two levels 121~5133

Two levels range from 12 to 100, and three levels can reach hundreds.

Single stage transmission efficiency

90%~94%

95%~98%

Multi-level cumulative efficiency

Two levels are about 85%~88%

Two levels 94%~96%, three levels 91%~94%

Large speed ratio scene efficiency

Single-stage direct output, superior overall efficiency

Multi-stage series connection, the cumulative loss is obvious

The conclusion is very straightforward: when the speed ratio is above 1:80, a single-stage cycloid machine can be realized, and the total efficiency exceeds that of a multi-stage planetary machine; but when the speed ratio is small and the machine runs continuously at high speed for a long time, the efficiency and temperature rise of the planetary machine are better. When calculating the speed ratio of the reducer , if the result falls in the range of 60 to 100, both types of models must be compared.

Reducer backlash and accuracy level: look at this item for servo applications

Backlash (return gap) determines positioning accuracy and is an item that clearly differentiates the two types of models. Servo-specific precision planetary reducers can reduce the backlash very low through grinding gears and preloading structures; cycloid machines are affected by the wear characteristics of the meshing surface, and the backlash of conventional models is relatively large. The precision grinding models can be narrowed but are still not as good as precision planetary models.

Backlash level

Typical values ​​(arcmin)

Corresponding models

Ultra high precision

≤1~3

Precision planet (ground helical gear)

Standard level

5~10

Universal planet, precision cycloid

conventional cycloid

10~20

Universal cycloidal pinwheel reducer

For scenes with stringent positioning requirements such as robot joints, CNC turntables, and laser cutting, precision planets should be selected based on backlash ≤ 3 arcmin; backlash 10~20 arcmin is completely sufficient for conveying, mixing, and general speed regulation. There is no need to pay a premium for unused precision. Also note: backlash should be viewed together with torsional stiffness. Load positioning error = no-load backlash + working torque ÷ torsional stiffness. When the stiffness is insufficient, the backlash will drift no matter how small it is.

Load bearing and impact resistance: overload margin for multi-tooth meshing

More than 30% of the tooth surfaces of the cycloidal machine are engaged in mesh at the same time, so the contact stress is dispersed. The instantaneous overload capacity can reach 2.5 to 3 times the rated torque. The backlash stability of forward and reverse rotation and frequent start and stop is also good. The rated torque of the planetary machine is about 70% to 80% of the cycloid machine under the same volume. The peak torque is generally calibrated at 3 times the rated value and lasts no more than 3 seconds. Therefore, cycloidal machines are more durable in heavy-load impact situations such as crushing, lifting, and mining transportation; while planetary machines are symmetrically loaded with multiple wheels and have small torque fluctuations, and perform more stably in automated lines with light and medium loads and high response. In terms of environmental adaptability, the integral box of the cycloidal machine has good sealing performance, is resistant to dust and moisture, and has a maintenance cycle of tens of thousands of hours.

Life, maintenance and purchase costs

The maintenance logic of the two types of machines is different: most cycloid machines use lithium-based grease for lifelong lubrication, which is basically maintenance-free and suitable for high-altitude, airtight, and inconvenient installation locations. Most of the precision and small planetary machines are lubricated with grease for life, while high-power oil-lubricated machines need to be inspected and changed every 2000 to 5000 hours. In terms of life, the rated life of an industrial-grade planetary machine is usually more than 20,000 hours based on L10. The cycloidal machine has multiple teeth to share the load, so the fatigue life of the tooth surface is also considerable. The short board is the wear monitoring of the pin tooth pin and the swing arm bearing. In terms of purchase cost, the cycloid machine with the same power is about 60% to 70% of the planetary machine, and the cost performance is outstanding in large speed ratio situations where accuracy requirements are not stringent.

Application scenario comparison and Selection four steps

Working condition characteristics

Priority model

in accordance with

Servo positioning, robot joints, CNC indexing

precision planet

Backlash ≤3 arcmin, stiffness and response

Large speed ratio (>80) heavy load low speed

Cycloidal pinwheel

Single stage direct output, efficiency and torque density

Frequent starts and stops, forward and reverse rotation, impact loads

Cycloidal pinwheel

Overload 2.5~3 times, multi-tooth meshing

Dust, moisture, inconvenient maintenance

Cycloidal pinwheel

Integrated box, maintenance-free lubrication

Light and medium load high speed continuous operation

planet

High efficiency, low temperature rise and low noise

There are four steps when it comes to operation: first calculate the speed ratio and output speed; then check the rated and peak torque according to the load torque multiplied by the service coefficient; then determine the backlash level according to the positioning requirements, and check the inertia ratio in the servo environment (converted inertia = load inertia ÷ speed ratio², recommended ≤5:1); finally check the mounting flange, shaft diameter and installation orientation. When comparing two types of models, count each of the four steps, and it will be clear at a glance which one falls within the allowable range.

If you are not sure which side the working conditions should fall on, you are welcome to consult Hangzhou Weigao Transmission . As a reducer manufacturer, we also provide a complete product line such as BLD cycloidal pinwheel reducers, hard tooth surface gear reducers, planetary and worm gears, etc., and support reducer customization and reducer quotation ; you can also open the Weigao reducer online Selection system to input parameters for self-service preliminary selection, or submit the working conditions and the engineer will issue a Selection plan. If you need on-site support from the Hangzhou reducer manufacturer , consultation or non-standard modification of the reducer , you can contact us to obtain technical parameters and drawings.

FEEDBACK

If the gear gap of the reducer is too large or too small, what efficiency problems will it cause?

How to adjust and repair the gear backlash of the reducer if it is too large or too small?

How to carry out dynamic inspection after FAF98-4KW-140-M4 gear reducer is installed

How to deal with abnormal vibration of WPDKS80-60 worm gear reducer under low load

What are the maintenance points for ZDY250-3.55-II hard tooth surface reducer in food plants?