Article List
- How to deal with abnormal noise in the reducer gear during operation1. Immediate shutdown and safety confirmation After discovering abnormal noise, the first step is to immediately shut down the machine for inspection to avoid the expansion of the fault and cause more serious damage. Under the premise of ensuring safety, disconnect the power supply and investigate the specific source of the noise to confirm whether the noise comes from the reducer itself, the motor or other connected components. 2. Core troubleshooting and treatment plan 1. Check the gear meshing and wear. Fault characteristics: If you hear periodic 'click' sounds, sharp metal friction sounds or knocking sounds, it usually indicates pitting, gluing, wear or even broken teeth on the gear tooth surface. Treatment method: Disassemble the reducer and check the condition of the gear tooth surface. If the tooth surface is damaged or chipped, it is necessary to replace it with a new gear of the same model; at the same time, clean the remaining metal debris inside the gear box to ensure that the meshing clearance of the new gear meets the standard (usually 0.1-0.2mm) to avoid impact caused by too large a clearance or aggravated friction if it is too small. 2. Check installation accuracy and connection failure
-
- Oil level maintenance and oil replenishment specifications for WPKS155-60 worm gear reducer1. Key operating specifications 1. Shutdown inspection Be sure to check the oil level when the reducer is completely stopped. During operation, the internal worm gear will cause the lubricating oil to splash. At this time, the observed oil level will be significantly higher due to the oil adhering to the gear and box wall, which cannot reflect the real oil amount and can easily lead to misjudgment. 2. For the correct oil level, add lubricating oil to 1/2 to 2/3 of the oil window (or oil mark). Too little oil: It will lead to insufficient lubrication and heat dissipation, accelerate the wear of worm gears and bearings, and even cause serious failures. Excessive oil volume: It will increase the internal oil stirring resistance, causing the oil temperature to rise abnormally. At the same time, excessive hydraulic pressure will impact the oil seal, which can easily cause oil leakage. 3. Standardize oil replenishment. If it is found that the oil level is lower than the lower limit of the oil window, the machine should be stopped immediately and replenished to the specified position after the equipment has cooled down. The lubricating oil specified in the equipment manual must be used (usually special oil for worm gears, such as L-CKE/P type or VG4
- What is the function of the oil level sight glass of WPA worm gear reducer?1. Intuitive monitoring of oil level: Reducers produced by regular manufacturers are usually equipped with a transparent oil window, which allows operators to directly observe the oil condition in the box without disassembling the equipment. For WPA worm gear reducers, the correct oil level usually needs to be maintained at 2/3 of the oil window (or the centerline position). 2. Ensure the lubrication and heat dissipation effect: Confirming that the oil level is sufficient through the oil level sight glass can ensure that the internal gears and worm gears of the reducer are fully lubricated, and avoid insufficient lubrication and poor gear splashing due to low oil level, which in turn aggravates component wear. At the same time, a suitable oil level can also prevent lubricating oil from splashing due to excessive oil level, affecting the heat dissipation effect or causing oil leakage. 3. Assisted judgment and standardized maintenance: The oil level sight glass provides an intuitive basis for daily inspection and regular maintenance of equipment. When checking or adding lubricating oil, it must be measured through the oil level sight glass when the reducer is stopped, because the oil level is
- How to quickly deal with oil leakage in NGW122-8 reducerRegarding the oil leakage problem of NGW122-8 reducer, if you want to deal with it quickly, you first need to clarify the specific location and cause of the oil leakage. The following are several quick troubleshooting and processing methods summarized for you: 1. Check and clean the breather cap (breather). When the reducer is running, the temperature rises and the internal pressure increases. If the breather cap (small nostril) is blocked by dust or sludge, the internal high pressure will force the lubricating oil out of the gap and cause oil leakage. Quick treatment of the breather cap: Unscrew the breather cap and check whether the small hole is unobstructed. You can use thin wire to clear it or clean it with compressed air. If the aging is serious, it is recommended to replace it directly. 2. Check and adjust the oil level. If too much oil is added, the oil pool will be violently stirred when the reducer is running, and the lubricating oil will splash everywhere and accumulate on the shaft seal, joint surface, etc., causing leakage. Quick oil level treatment: Observe the oil dipstick scale. If the oil level is too high, drain off the excess lubricating oil to keep the oil level within the normal scale range.
- What are the common causes of oil leakage in NGW122-8 reducer?1. There is a pressure difference between the inside and outside of the reducer. During the operation of the reducer, gear meshing friction and heat and the influence of ambient temperature will cause the temperature inside the machine to rise. Since the volume of the box remains unchanged, the internal pressure increases. If the ventilation holes are too small or blocked by dust or oil, the machine cannot equalize the pressure with the outside world, and lubricating oil will seep out from the gaps that are not tightly sealed under the pressure difference. 2. Unreasonable structural design or manufacturing process, box deformation and gaps: If the casting is not fully annealed or aged during manufacturing, the internal stress is not eliminated, and it is easy to deform and create gaps in subsequent use; in addition, if the inspection hole cover is too thin, it will easily deform after tightening the bolts, resulting in an uneven joint surface, which will cause leakage. Poor return flow: If there is no oil return groove designed on the box, the lubricating oil thrown by the gear to the shaft seal, end cover or joint surface cannot flow back to the oil pool, and will easily leak out under the action of pressure difference. Shaft seal defects: Early or poorly designed shaft seal construction (e.g. felt seal)
- What are the differences in the installation methods of ZSY reducer and DCY gear reducer?1. The number and definition of assembly forms are different (1) ZSY: A total of 9 assembly forms (I~IX) through different orientation combinations of input shafts and output shafts on the box to cover various layouts such as left/right/upper/lower extension of the input shaft, left/right extension of the output shaft, etc. It can adapt to general industrial scenarios with limited space and changeable motor layout directions (2) DCY: only 4 assembly forms (I~IV) Type I: Left-out shaft (conventional type) Type II: Right-out shaft (conventional type) III Type: The left output shaft that can be installed with a backstop Type IV: The right output shaft that can be installed with a backstop Since the input and output shafts have been fixed at 90° vertical, the assembly form only distinguishes the left and right sides of the output shaft and whether it has a backstop position 2. Differences in backstop configuration DCY: Types III and IV have a backstop (brake) installation position reserved at the factory. They are specially designed for belt conveyors and other working conditions that require anti-reversal, and are standard configuration options Z
- What measures should be taken immediately when the WP series worm reducer is overloaded?1. Stop the machine immediately and cut off the power supply. Once the reducer is found to be overloaded (such as abnormal noise, severe vibration, excessive temperature rise, etc.), it must be stopped immediately and the power supply cut off. Continuous operation under high temperature or overload conditions is strictly prohibited to prevent more serious damage such as gluing of the worm gear or burning of the motor windings. 2. Check and eliminate the overload source. In the shutdown state, check in detail whether there is a fault on the load side, such as whether the equipment is stuck, whether the material is blocked, etc. Only after the direct cause of the overload is confirmed and eliminated can restarting be considered. 3. Check the lubricating oil status. Overloading is often accompanied by severe heating. It is necessary to check whether the lubricating oil level of the reducer is sufficient and whether the oil quality has deteriorated. If the oil becomes thinned, emulsified or contains a large amount of impurities due to high temperature, it is necessary to replenish or replace the lubricating oil that meets the specifications in time to restore good lubrication status. 4. Check the wear of mechanical components. Overloading can easily cause damage to internal transmission components. The worm gear should be inspected mainly
- What are the early signs of gear burn in TY series reducer?1. Abnormal auditory and olfactory signals, piercing screams and friction sounds: Under high-speed and heavy-load conditions, if the tooth surface lubrication fails, causing a sudden rise in local temperature, and the metal surface is fused and then torn apart, severe 'piercing screams' or 'scorching sounds' will be produced, accompanied by strong metal friction noises. Odor generation: When severe gluing or burns occur, obvious odors can often be smelled, such as the smell of oil or burning metal. 2. Abnormal temperature and vibration. The shell temperature rises sharply: Excessive temperature rise is an important signal of gear damage. If the surface temperature of the reducer housing continues to rise or is locally hot (for example, a seriously high state exceeding 60°C), it indicates that the internal friction power has increased sharply, and a high degree of vigilance is required. Increased vibration: Along with abnormal noise, the device usually experiences significant body vibration. This kind of vibration is often caused by metal adhesion and severe friction on the tooth surface. 3. The condition of the lubricating oil deteriorates and the oil temperature suddenly rises: during actual operation
- Which light-load equipment is suitable for ZDY series gear reducer?1. Light-load conveying equipment 1. Light belt conveyor: Light material feeding, sorting and transportation, no big impact, short-distance belt line 2. Roller conveyor line: Light roller, sorting line roller drive, continuous and smooth operation 3. Small screw conveyor: Light conveying of powder materials, non-large displacement heavy-duty auger 4. Light bucket elevator: Small lifting of grain and powder, no impact of large materials 2. Fans and pumps 1. Centrifugal fans, induced draft fans: industrial ventilation, dust removal fans, high speed and low deceleration requirements, ZDY is very suitable for fan working conditions 2. Industrial water pumps, circulating pumps: pump transmissions with large speed ratios, no impact load 3. Light industrial textile and pharmaceutical equipment 1. Textile equipment: cloth rolling machine, printing and dyeing roller, finishing machine transmission, low noise continuous operation 2. Pharmaceutical equipment: mixer, granulator, packaging machine auxiliary transmission, light torque stable output 3. Grain and feed light industry: small cleaning sieve, light stirring, simple sieve