Worm Gearbox Self-Locking vs Back-Driving: Hoist and Conveyor Selection Rules
Publish Time: 2026-10-25 Origin: Site
Why Worm Gearbox Self-Locking Decides Hoist Safety
Every worm gearbox driving a hoist or an inclined conveyor faces the same physics question: can the load turn the input shaft backwards? A correctly chosen self-locking worm gear holds the load when power is cut; the wrong ratio lets it creep, coast or run away. This guide gives the selection rules in numbers — lead angle limits, the efficiency penalty you must accept, the three things that break self-locking in service, and where a back driving gearbox is actually the better choice.
The Self-Locking Condition in One Formula
Self-locking occurs when the worm lead angle (λ) is smaller than the effective friction angle (ρ′), where tan ρ′ equals the tooth friction coefficient μ. Field-safe practice: λ ≤ 3–5° gives reliable static self-lock; above 6° the worm gear pair is generally back-drivable. Because lead angle falls as ratio rises, single-start worms at 20:1 and above are normally self-locking, and 30:1 adds a working margin. Always ask the supplier for the actual lead angle on the drawing, not a catalogue claim.
The Efficiency Trade-Off You Cannot Design Around
Worm gear reducer efficiency and self-locking come from the same equation: η = tan λ / tan (λ + ρ′). A drive that self-locks reliably runs below roughly 50% forward efficiency; a drive near 80% efficiency will back-drive at operating temperature. Measured data also shows 7–8 percentage points between cold and warm oil — size the motor on cold-start values to avoid nuisance overload trips.
Ratio (single start) |
Lead angle |
Forward efficiency |
Back-driving risk |
|---|---|---|---|
10:1–15:1 |
6°–8° |
80–86% |
Back-drives — not self-locking |
20:1–30:1 |
3°–5° |
65–77% |
Marginal — verify friction data |
40:1–60:1 |
2°–3° |
55–68% |
Reliable static self-lock |
What Breaks Self-Locking in Service
Three mechanisms quietly cancel a self-locking worm gear. Heat: sump temperature of 80–90 °C lowers the oil film and friction coefficient, and creep has been measured at ratios as low as 1:30 in continuous duty. Vibration: each shock cycle momentarily breaks static friction and advances the output a small angle, accumulating into visible load drop over hours. Wear and lubrication: polished flanks and extreme-pressure or low-friction synthetic oils reduce μ over time. Verify the self-lock condition at the highest expected operating temperature, never at ambient bench conditions.
When Back Driving Is a Feature, Not a Fault
A back driving gearbox is the right answer where the load must return energy or coast down: centrifuge run-down, fan rotors, agitators that must not trap torque, or screw feeds that need controlled return. There, specify a multi-start worm or move to a helical stage and handle holding with an external brake. Trying to get high worm gear reducer efficiency and guaranteed self-locking from one unit is a specification error — the physics forbids both.
Hoist Gearbox Selection Rules
For any hoist gearbox carrying suspended loads, treat self-locking as secondary protection only and fit a rated brake as the primary device, as Australian AS 2549 and WHS codes require. Sizing example: a 2,000 kg load on a 200 mm drum radius gives T = 2,000 × 9.81 × 0.2 ≈ 3,924 N·m at the drum; through 3:1 chain reduction the gearbox output needs about 1,308 N·m, so a 1:30 unit rated 1,782 N·m fits with margin. Keep holding torque at least 1.5× the maximum load torque and back-drive torque below one third of the critical self-locking torque.
Inclined Conveyor Selection Rules
On an inclined conveyor, first decide what must happen when power fails: rollback prevented, or rollback allowed under control? If rollback must be prevented, specify a mechanical holdback or backstop as the primary device and let the worm pair assist — do not make friction the only barrier, since belt bounce and shock loads defeat it. Where controlled coast-down is acceptable, a higher-ratio helical or a 15:1–20:1 worm drive with a service factor of 1.5–2.0 usually runs cooler and wastes less power.
What to Verify Before You Order
Before releasing a purchase order, get four items in writing: the worm lead angle from the drawing; the material pair (hardened and ground steel worm with centrifugally cast bronze wheel); tested holding torque at your maximum sump temperature; and the declared back-driving behaviour per ratio. A supplier who cannot produce these numbers is selling a catalogue adjective, not an engineered hold. WGT builds worm gearbox units from 20:1 to 100:1 with documented lead angles and material certificates, and supplies SEW and NORD compatible replacement worm gear reducers for hoists, lifts and inclined conveyors — send us your load, drum size and duty cycle, and our engineers will return a checked selection with holding-torque verification.