WPWD100 Worm Gear Reducer Universal Reducer
Product Description
The WPWD100 worm gear reducer is the 100 mm centre-distance member of WGT Weigao Transmission's universal worm gear speed reducer family, supplied in the WPWD execution, meaning the gearbox carries an integral motor flange on its input side so the drive motor bolts straight onto the housing instead of being coupled to it through a separate bracket. That single feature turns an ordinary worm gearbox into a compact, self-contained drive package. The WPWD100 uses a single-stage Archimedean cylindrical worm drive and covers factory ratios from 1/10 up to 1/60, so the same frame serves slow conveyor rolls, packaging lines, augers, fans and machine-tool feeds. For buyers working through gear reducer selection and gearbox sizing, the figures below are factory catalogue data for this exact model, not generic family ranges.
The model designation reads directly once the code is broken down: W is the product code for a worm gear speed reducer, P the whole one-piece box structure, the second W the universal box model, and D the input shaft with motor flange; the trailing number is the centre distance in millimetres. The WP universal family runs from 40 mm to 250 mm - WPWD40 to WPWD250 in twelve sizes including WPWD100 - and all of them share the same housing family, oil seals, bearings and selection method, so changing centre distance is a change of frame rather than a new design.
Typical Specifications of the WPWD100 Worm Gear Reducer
| Item | Typical Range | Notes |
|---|---|---|
| Type | Single-stage universal worm gear reducer with integral motor flange | WPWD execution: D = input shaft with motor flange; right-hand worm thread as standard |
| Centre distance | 100 mm | One-piece box structure (P code); family spans 40 - 250 mm |
| Factory ratios | 1/10, 1/15, 1/20, 1/25, 1/30, 1/40, 1/50, 1/60 | Eight catalogue ratios for this centre distance |
| Rated input power | 1.5 kW at 1500 r/min | Rated with AO2 or Y series motor; catalogue torque values are quoted at 1500 r/min |
| Rated output torque | 80 - 344 N·m | 80 N·m at 1/10 rising to 344 N·m at 1/60 |
| Output speed | 25 - 150 r/min | From 1500 r/min input: 150 / 100 / 75 / 60 / 50 / 37.5 / 30 / 25 r/min |
| Permitted input speed | Not above 2000 r/min; 600 - 1800 r/min normal | Excessive input speed shortens bearing life |
| Motor flange | 4 × M10 holes, Ø165 bolt circle | Flange Ø200 (LC) / Ø130 (LB), thickness LE 4.5 mm |
| Input bore | Ø24 × 52 mm, key 8 × 27.3 mm | Catalogue codes Q / U / T×V |
| Output shaft | Ø38 × 75 mm, key 10 × 5 mm | Catalogue codes S / LS / W×Y |
| Envelope | 280 (A) × 216 (AC) × 310 mm high (H) | Housing 169 mm wide (BB); feet 8 × M12×30 |
| Mass | 36.5 kg | Reducer only, excluding the drive motor |
Table shows the WPWD100 catalogue data. Torque and power are catalogue values at 1500 r/min input; every installation must still be verified against its own duty cycle, and the reducer oil temperature limit is 95 °C.
Rated Output Torque and Output Speed of the WPWD100 by Ratio
| Ratio i | Output speed at 1500 r/min | Rated input power | Rated output torque | Catalogued efficiency range |
|---|---|---|---|---|
| 1/10 | 150 r/min | 1.5 kW | 80 N·m | 75 - 84 % |
| 1/15 | 100 r/min | 1.5 kW | 115 N·m | 72 - 82 % |
| 1/20 | 75 r/min | 1.5 kW | 149 N·m | 68 - 82 % |
| 1/25 | 60 r/min | 1.5 kW | 181 N·m | 77 - 90 % |
| 1/30 | 50 r/min | 1.5 kW | 198 N·m | 76 - 88 % |
| 1/40 | 37.5 r/min | 1.5 kW | 260 N·m | 64 - 75 % |
| 1/50 | 30 r/min | 1.5 kW | 307 N·m | 62 - 72 % |
| 1/60 | 25 r/min | 1.5 kW | 344 N·m | 60 - 71 % |
Torque figures are the maximum load the catalogue allows for this frame at the stated ratio and input speed. Efficiency falls as the ratio rises, which is why a high-ratio build needs more input power for the same shaft torque.
Where This Universal Worm Gear Reducer Is Used
- Small belt and roller conveyors: the integral motor flange removes the need for a separate motor bracket, so the drive packs into a narrow machine frame where a conventional geared motor would not fit.
- Screw and auger conveyors: light-duty grain and feed augers at 25 - 60 r/min, where the worm drive holds the auger speed steady under varying feed load.
- Packaging machinery: wrapping, labelling, carton sealing and intermittent collation drives, where a 1/20 to 1/30 ratio delivering 50 - 75 r/min is the usual working point.
- Machine tools and coolant systems: feed drives, tool slides and pump drives where a compact, low-maintenance unit with a keyed output shaft is preferred to a separate gearbox.
- Fans, blowers and ventilation equipment: centrifugal fan drives at 25 - 100 r/min, with the reducer mounted directly on the fan inlet or coupled to the fan shaft.
- Textile, printing and woodworking machinery: intermittent feeds and rollers running 10 to 24 hours a day, and therefore sitting in the higher service-factor columns of the selection table.
Selection Example: 1.5 kW Drive for a 60 r/min Packaging Roller
A packaging line needs a roller driven at 60 r/min by a 1.5 kW, 1500 r/min motor. The roller delivers a theoretical output torque of 150 N·m, runs 8 hours a day on a uniform load, and is stopped and restarted about 15 times per hour.
Step 1 - Ratio. i = 1500 / 60 = 25, so the catalogue ratio is 1/25. The 1500 r/min input sits inside the recommended 600 - 1800 r/min band and well below the 2000 r/min ceiling, so the worm set is not being over-speeded.
Step 2 - Power sanity check. The driven machine needs 150 × 60 / 9550 = 0.94 kW at the shaft, inside the 1.5 kW motor rating before any service factor is applied.
Step 3 - Service factor. For a uniform load at 6 - 10 hours per day the catalogue running condition factor K is 1.00. Because the roller is stopped more than 10 times per hour, K must additionally be multiplied by 1.2, giving K = 1.20. (Uniform load 0.80 / 0.90 / 1.00 / 1.25 for 0.5-2, 2-6, 6-10 and 10-24 hours per day; medium shock 0.90 / 1.00 / 1.25 / 1.50; heavy shock 1.00 / 1.25 / 1.50 / 1.75.)
Step 4 - Revised torque. T2 = T1 × K = 150 × 1.20 = 180 N·m.
Step 5 - Catalogue check. At 1/25 the WPWD100 is rated 181 N·m, so 181 ≥ 180 and the unit passes - but with almost no margin. Upgrade to a medium or heavy shock duty and the revised torque becomes 188 to 225 N·m, at which point the WPWD100 no longer qualifies; the next step is the WPWD120, rated 372 N·m at 1/25 with a 3 kW input capacity that the same 1.5 kW motor can still drive.
Step 6 - Motor power confirmation. Working backwards with the catalogue efficiency for 1/25, P = 180 × 60 / (9549 × 0.77) = 1.47 kW, so the 1.5 kW motor is right at the limit for that frame. Drive speed, duty hours and shock class all move this answer, which is why the calculation is repeated rather than assumed - and why the selection system below is faster than working from the catalogue by hand.
Installation, Lubrication and Maintenance Notes
Mount the reducer on a flat, rigid base plate with the foot bolts tightened, and align the prime mover, reducer and driven machine so the three shaft lines are coaxial. Input shaft extensions are machined to J6 and output shaft extensions to JS6, so couplings, pulleys and sprockets must be bored to a matching tolerance - too tight and the bearings are damaged, too loose and the power transmission suffers. Sprockets and gears should sit close to the bearings to limit shaft bending, and when bolting a motor to the WPWD input flange, grease the bore wall and keyway of the worm shaft; if the motor is heavier than usual, provide a separate support. Output rotation follows the right-hand worm thread as standard: with the motor running clockwise, the output shaft turns anticlockwise on the WPA form and clockwise on the WPS form.
Fill the housing with N220 to N320 oil for ambient temperatures of -30 to 40 °C, or N320 to N460 for 40 to 65 °C, up to the centre line of the oil gauge, and remove the small cone plug from the breather before starting. The catalogue also lists ISO VG 200, 320 and 460 mineral oils, synthetic PG 220 and PG 460 grades and AGMA/CSSO oils. Flush and refill after the first 100 hours, then change the oil every 2500 hours; oil temperature may reach 95 °C provided it is not still rising. Typical faults have simple causes: overheating from oil seal friction, too much or too little oil, or oil contaminated with impurities; vibration from poor alignment, overload, worn worm gear teeth or bearings; noise from poor tooth contact, insufficient oil or a foreign object in the housing; and oil leakage from overfilling, a loose drain plug or a damaged oil gauge. Where the load overhauls the drive, confirm back-drive behaviour for the selected ratio before ordering, because the WP series is not published with a lead-angle table.
Get the Exact Model Online — Free Selection System
Open the WGT Motor & Gearbox Online Selection System, enter your power, input speed, required output speed or ratio, plus the torque and duty of the driven machine, and the system returns the matching reducer size, ratio and rating with the full technical data. It removes the arithmetic and the judgement calls from service factor gearbox work and is the fastest route to a firm quotation for a worm gear reducer maintenance spare or a new drive. To cross-reference against SEW, NORD, Flender or a Chinese equivalent, send us the nameplate photo or type designation and our engineers will reply with the cross-reference, price and lead time.