Structural principles and Selection key points of planetary reducer: how to determine the speed ratio, series and backlash - Hangzhou Weigao Transmission
Publish Time: 2026-10-17 Origin: Site
Structure of planetary reducer: transmission logic of four core components
In various types of planetary reducers , power transmission relies on the coordination of four core components: the sun gear in the center (connected to the input shaft), 3 to 6 planetary gears evenly distributed, the fixed internal ring gear, and the planet carrier that aggregates power. After the motor drives the sun gear to rotate at high speed, the planet gear rotates while rotating along the inner wall of the fixed inner ring gear, and finally drives the planet carrier to rotate at a low speed and output. Since multiple planetary gears share the load at the same time, this compound motion of 'rotation + revolution' enables the planetary reducer to achieve high power density in a compact size, which is also the fundamental structural difference between it and the parallel-axis gear reducer. The single-stage reduction ratio can be estimated according to the formula i = 1 + Zr/Zs (Zr is the number of teeth of the internal ring gear and Zs is the number of teeth of the sun gear). For example, if the ring gear has 80 teeth and the sun gear has 20 teeth, the single-stage speed ratio is 5.
Reducer speed ratio calculation and series selection
When calculating the speed ratio of the reducer , divide the rated speed of the motor by the output speed required by the load to get the speed ratio. The common practice in the industry is to give priority to standard speed ratios such as 3, 4, 5, 7, 10, 20, 25, and 40. Non-standard speed ratios have high costs and long stocking cycles. If the single-stage speed ratio exceeds 10, it is recommended to change to double-stage. If the speed ratio exceeds 50, it is recommended to use three-stage. It is more economical and reliable to use standard speed ratio stacking (such as 5×10=50) than to customize a single-stage large speed ratio. The performance differences of different levels are shown in the table below:
structure | Common speed ratio range | Single stage transmission efficiency | Volume and backlash characteristics |
|---|---|---|---|
single stage | 3~10 | About 95%~97% | Short body, high efficiency, small backlash |
Dual level | 12~100 | The whole machine is about 90%~94% | Large torque and slight accumulation of backlash |
Level three | 100 or more | The whole machine is about 85%~90% | Large speed ratio, long body and increased heat generation |
It should be noted that the more stages, the greater the backlash accumulation and the lower the efficiency. For continuous operation, you should try to choose a model with fewer stages and high efficiency to avoid problems with heat generation and energy consumption.
How to choose a precision planetary reducer: matching backlash, stiffness and inertia
Servo reducer matching is the main application scenario of precision planetary reducer . At this time, the backlash of the reducer is the core indicator: the free travel angle of the input shaft when the output shaft is fixed, measured in arc minutes (arcmin). General reference: select 1 to 3 arc minutes for high-precision positioning scenarios such as robot joints and CNC machine tools; select 5 to 10 arc minutes for ordinary automated transmission; pure power transmission can be relaxed to 10 to 15 arc minutes. In addition to backlash, it also depends on the torsional stiffness (heavy gear models with high rigidity are required for heavy-duty cutting and precision indexing) and inertia matching - the load inertia converted to the motor side is the load inertia divided by the square of the reduction ratio. It is recommended that the ratio after conversion to the motor rotor inertia be controlled within 5 to 10, otherwise the servo system is prone to slow response, positioning overshoot and even oscillation. In the case of frequent forward and reverse rotation, the long-term stability of the backlash should also be confirmed.
Torque Calibration and Service Factor: Don’t Just Look at Motor Power
Output torque at Selection = motor rated torque × speed ratio × transmission efficiency, multiplied by the appropriate service factor of the reducer (generally 1.2 to 1.8, take the larger value for impact loads and frequent starts and stops). The hard and fast rule is: the actual continuous load torque must be less than the rated torque of the reducer, and the instantaneous torque of start-stop or impact must be less than the peak torque (usually within 3 times the rated value, and the duration does not exceed a few seconds). Common misunderstandings include: only matching motor power without looking at torque conversion, ignoring the radial cantilever load of the output shaft (especially when driving pulleys and sprockets), and not confirming the lubrication scheme in low or high temperature environments. By checking these parameters one by one, the planetary reducer can have margins without excessive waste of costs.
Selection support provided by Hangzhou Weigao Transmission
As a reducer manufacturer, Hangzhou Weigao Transmission 's product lines cover cycloidal pinwheel reducers, hardened cylindrical gear reducers, worm gear reducers, gear reduction motors, etc., and can provide free reducer consultation based on your motor power, speed, torque and installation interface . If you are comparing solutions from Hangzhou reducer manufacturers or need to replace existing imported brand models, please provide working condition parameters or equipment nameplate photos, and we will issue complete Selection solutions and technical parameters for your reference.