SWC-Ⅰ type universal coupling

Product Description

The SWC-Ⅰ type universal coupling is the light cross-shaft universal coupling in WGT's SWC programme, built to JB/T 5531-1991 for drives where two shafts cannot be lined up and the joint has to absorb a real angle while still passing torque smoothly. Three versions share one size ladder: A type telescopic welded, B type fixed-length welded and C type short single-unit. Nominal torque runs from 180 N·m to 22 000 N·m over ten sizes, SWC-Ⅰ 58 through SWC-Ⅰ 225, and the maximum working axis angle reaches 35° on the small and medium sizes — far beyond what a flange coupling can tolerate. Against the small fixed-pin universal joints of the CSKA and WS series, the SWC-Ⅰ is a heavy cross-shaft construction with far more torque per joint and much better shock tolerance, while its light build keeps rotating inertia low for a machine that starts and stops all day.

Typical Specifications of the SWC-Ⅰ Type Universal Coupling

Model Nominal torque Tn (N·m) Fatigue torque Tf (N·m) Max axis angle β (°) Rotation diameter Df (mm) D1 (mm) D2 (mm, H9) A-type length L (mm) A-type mass (kg) Flange bolts Bolt torque TK (N·m)
SWC-Ⅰ 58 180 90 35 58 47 30 255 2.2 M5 7
SWC-Ⅰ 65 240 120 35 65 52 35 285 3 M6 13
SWC-Ⅰ 75 500 250 35 75 62 42 335 5 M6 13
SWC-Ⅰ 90 800 400 35 90 74.5 47 385 6.6 M8 32
SWC-Ⅰ 100 1200 600 35 100 84 57 445 9.5 M8 32
SWC-Ⅰ 120 2300 1150 35 120 101.5 75 500 17 M10 64
SWC-Ⅰ 150 4500 2250 35 150 130 90 590 32 M12 110
SWC-Ⅰ 180 8400 4200 25 180 155.5 110 640 40 M14 180
SWC-Ⅰ 200 16000 8000 25 200 170 125 775 76 M16 270
SWC-Ⅰ 225 22000 11000 25 225 196 140 860 128 M16 270

WGT catalogue values for the SWC-Ⅰ series. Tn is the nominal torque, taken at 50 % of yield torque; Tf is the fatigue torque, the permissible torque under reversing load set by fatigue strength. Df is the rotation diameter and equals the model number; D1 and D2 are the two principal diameters of the type drawing, D2 specified to H9 fit. A-type mass is for the telescopic welded version; the fixed-length B and C types weigh less at every size. WGT publishes 98.7–99.9 % transmission efficiency and 30–40 dB(A) noise for the SWC family. Non-standard lengths, extension strokes and flange sizes are available on request.

Three Configurations: A Type, B Type and C Type

Type Construction Standard length across SWC-Ⅰ 58–225 Where it fits
A type Telescopic welded L 255–860 mm, with an extension stroke on every size Long spans where the frame moves, or where thermal growth must be taken up without moving the machine
B type Fixed-length welded L 150–600 mm Rigid, permanently aligned installations with no axial movement
C type Short single-unit L 128–480 mm Compact drives where the shafts sit close together and swing is small

Lengths are the WGT standard lengths; for telescopic versions L is the minimum length in the fully retracted state. Custom lengths and flange patterns are made to order.

Where This Universal Coupling Is Used

  • Steel rolling mills: small and medium section mills, continuous wire mills, roughing mills and mill housing roller tables, where the drive shaft swings through the mill stroke.
  • Crane and heavy transport drives: crane main and auxiliary drives, conveyor main drives and conveying roller tables, all of which reverse and absorb shock.
  • Heavy presses, straighteners and shears: presses, plate straighteners and thick plate shears, where a stiff joint keeps the ram on its line under load reversal.
  • Mills, mixers and crushers: ball mills, mixers, crushers and single-cylinder compressors — heavy-shock duties needing the fatigue torque, not just the nominal figure.
  • Light machinery and ship drives: fans, pumps, belt conveyors, woodworking spindles and multi-cylinder compressors, where the joint only has to absorb light or medium shock but still wants a large working angle.

Selection Example: 15 kW Mixer Drive at 750 r/min

A paint and resin mixer has a 15 kW motor at 750 r/min, the mixer shaft sitting 6° out of line with the motor. The impeller starts against a heavy viscous load several times a shift, so this is a reversing, high-inertia duty.

1. Theoretical torque. T = 9550 × P / n = 9550 × 15 / 750 = 191 N·m. The mixer falls in the heavy-shock group, so a service factor of K = 2.5 applies — the WGT table gives 2–3 for mixers. Calculated torque is Tc = 2.5 × 191 = 477.5 N·m.

2. Use fatigue torque, not nominal torque. Because the load reverses, compare 477.5 N·m against the fatigue torque column. SWC-Ⅰ 90 gives Tf = 400 N·m and is rejected; SWC-Ⅰ 100 gives Tf = 600 N·m and is accepted with a 1.26× margin, against a nominal torque of 1200 N·m. If start-up proves harsher, take K = 3.0 and the next size up.

3. Check the angle. The maximum axis angle of SWC-Ⅰ 100 is 35°, so the 6° offset is comfortable. Remember the SWC rule for equal angular velocity: the two joints must sit at equal angles β1 = β2, the fork ends of the intermediate shaft must be in the same phase, and the three shaft centrelines must lie in one plane. Installations are classified as Z type (parallel axes) or W type (intersecting axes).

4. Choose the construction and set the length. The mixer base settles slightly, so the A type telescopic welded version is used: L = 445 mm, mass 9.5 kg. Flange bolts are M8 and must be tightened to 32 N·m — a loose flange is the most common cause of vibration in a cardan drive.

5. Carry the same factors upstream. That 2.5 service factor belongs on the reducer as well: a service factor gearbox sized with a lower factor will stall on start-up even when the coupling is correct. Feed 477.5 N·m and 750 r/min into your gear reducer selection and gearbox sizing work, then confirm bearing life and thermal rating at the mixer shaft.

Upkeep follows the same discipline. A cardan joint is a maintenance item, not fit-and-forget: put cross-shaft bearing lubrication, flange bolt re-torque and a fork play check into the gearbox maintenance plan, on the reducer oil change schedule.

Get the Exact Model Online — Free Selection System

Open the WGT Motor & Gearbox Online Selection System, enter your power, input speed and required torque, and the system returns matching models with technical data in seconds. Need a cross-reference against an imported SWC, WSS or Japanese cardan shaft? Send the type designation and our engineers will reply with the equivalent, price and lead time within 24 hours.

Product Inquiry

WX, WXD type small cross shaft universal coupling (JB/T5901-1991)

G and GD precision universal joints

GR and HR precision universal joints

WS/WSD small universal joint (JB/T5901-1991)

CSCA/CSCW universal joint