How to determine the export packaging of reducers: wooden box structure, fumigation mark and drop impact calibration example - Hangzhou Weigao Transmission
Publish Time: 2026-11-15 Origin: Site
How to determine the export packaging of reducer: wooden box structure, fumigation mark and drop impact check calculation example
To pack a reducer into a wooden box and send it overseas, you have to deal with four things at the same time: the drop impact during loading and unloading, the static load in the yard, the angle stress of the sling, and the moisture and rust caused by dozens of days of shipping. There are standards to follow for these things: GB/T 191-2025 for graphic signs, ISPM 15 for quarantine, GB/T 4857 series for transportation testing, and strength is calculated according to working conditions. The following uses a 320 kg two-stage hard tooth surface reducer to walk through the design and verification calculation examples of export wooden boxes.
Export wooden boxes must meet four requirements: the storage and transportation instructions should be marked with graphic symbols according to GB/T 191-2025; the quarantine should be heat treated according to ISPM 15 and IPPC markings should be added; the transportation test should be done according to the GB/T 4857 series; the structural strength should be calculated according to the contract conditions. Among the GB/T 4857 series, those directly related to export boxes include static load stacking (GB/T 4857.3-2008), drop (GB/T 4857.5-1992), spray (GB/T 4857.9-2008) and performance test program (GB/T 4857.17-2017). They are all current versions and should be written into the technical agreement or inspection basis.
1. Marking and fumigation: two requirements that cannot be omitted
1.1 Logo: The standard has changed its version, and the export parts can be simplified.
GB/T 191-2008 "Pictorial Symbols for Packaging, Storage and Transportation" has been completely replaced by GB/T 191-2025 "Pictorial Symbols for Packaging, Storage and Transportation" on March 1, 2026. The new version will be released on August 29, 2025, and the modification will adopt ISO 780:2015. There are still 17 types of graphic symbols, but they are now classified according to 6 tables; the names have also been adjusted, fragile items are changed to Fragile and Handle with Care, and Fear of Rain is changed to Avoid Rain.
The most practical one for export items is Article 6.1.1: when printing the mark, the outer frame line and the name of the mark should be printed, but the Chinese mark name and outer frame line can be omitted for exported goods, and both can be omitted when spraying. Article 6.1.2 limits that only 8 types of signs are allowed to be hand-painted, including prohibition of hand hooks, prohibition of forklifts, prohibition of rolling, limit of stacking layers, prohibition of stacking, etc. The values of stacking layers and quality can also be manually rewritten according to the contract. The size is divided into four levels, with the largest outer frame being 200×200 mm; the color is generally black, and standards require avoiding red, orange and yellow to avoid confusion with dangerous goods signs.
Logo name | meaning | Usage on export wooden boxes |
|---|---|---|
center of gravity | Center of gravity position | Mark when it is too heavy |
hoisted from this | Lifting position | Mark the location of the lifting straps |
Pick up from this | Clip position | Mark the sliding wood clamping points |
Keep out of the rain | Rainproof | Shipping boxes must be marked |
up | Must be placed upright | Mark when the axis is pointing up |
Limit of stacking layers | Number of stacking layers allowed | Can be modified manually according to the contract |
1.2 Fumigation and IPPC marking: 56 ℃ and 30 minutes are hard indicators
Wooden packaging exported to countries with phytosanitary requirements must comply with ISPM 15 "Management of Wood Packaging Materials in International Trade". Crates, packaging boxes, dunnage, and pallets are all within the scope of control. There are also exemptions: packaging made entirely of thin wood with a thickness of 6 mm or less, as well as multi-layer boards, particle boards, etc. based on treated wood are not subject to restrictions.
Heat treatment (marking code HT) requires the entire wood including the wood core to reach a minimum temperature of 56°C and maintain it for at least 30 minutes. It can be measured by a sensor inserted into the wood core, or a test treatment can be used to establish a program and prove that 56°C is maintained continuously for 30 minutes. Methyl bromide remains in the standard despite the IPPC"s promotion of substitution, but Annex 1 clearly states that wood with a minimum cut surface exceeding 20 cm shall not be treated with methyl bromide. The mark specified in Annex 2 consists of four parts: IPPC symbol, ISO two-letter country code (CN in our country), producer or treatment provider code, treatment code HT, DH, MB or SF. The processing code must be in a separate line. The mark must be clear and legible, permanently non-transferable, and must not be handwritten. It should be marked on two opposite sides of the wooden packaging unit. The skidding must also be processed and marked.
2. Strength Calculation Example: Which Working Condition Controls the Design of Wooden Boxes
2.1 Calculation example parameters
A two-stage hard-tooth surface cylindrical gear reducer for export is equipped with a gear reduction motor, with a net weight of 320 kg, and an appearance of 900×500×620 mm. It is equipped with a pine export box, with a dead weight of 48 kg, a total packing weight of 368 kg, an appearance of 1080×640×760 mm, and a section of 4 columns of 60×60 mm. The contract stipulates that the number of stacking layers is limited to 4 layers.
2.2 Loads in three working conditions
The first working condition is stacking. The bottom box bears all the weight of the three floors above, 3×368×9.81 = 10 830 N. Each of the four columns is 2 708 N, and the column compressive stress is 2 708÷3 600 = 0.75 MPa. This magnitude is far lower than the design allowable range of packaging wood. Stacking does not control the strength, but it determines how large the stacking layer limit can be written in the contract.
The second working condition is hoisting. For 4-point hanging, the tensile force of a single sling is S = W/(4 cos θ), θ is the angle between the sling and the plumb line: 903 N for vertical hanging, 1 042 N for 30°, 1 276 N for 45°, and 1 805 N for 60°, which is exactly twice that of vertical hanging. If the center of gravity is 60 mm away from the center of the hanging point and the distance between the hanging points is 1 000 mm, the maximum hanging point F = W/4 + W·e/(2L) = 1 011 N, and the minimum point is 794 N, a difference of 1.27 times; after superimposing the 45° sling angle, the maximum sling force rises to 1 430 N.
The third working condition is drop impact. The drop height h at the bottom of the box, the buffer stroke s, and the peak acceleration a = 2gh/s when approximated by a linear spring, the peak resultant force F = m·a. Assume h = 0.30 m, s = 100 mm, a = 6.0 g, the peak resultant force = 368×58.86 = 21 660 N, and the amount transmitted to the reducer mounting surface is 320×58.86 = 18 835 N. In the event of a 300 mm drop, the force acting on the mounting surface is 5.2 times the weight of the box.
Working conditions | Calculation formula | load | Whether to control |
|---|---|---|---|
Stack 4 layers | 3×m×g | 10 830N | 否 |
column compression | F÷(4×3 600 mm²) | 0.75MPa | 否 |
Hoisting 45°, eccentricity 60 mm | (W/4 + W·e/2L)÷cos45° | 1 430N | 否 |
Drop 0.30 m/100 mm | m×2gh/s | 21 660N | 是 |
2.3 Back calculation of buffer stroke
Press the drop impact to not exceed the stacking load, and back-calculate the buffer stroke: s ≥ m×2gh÷F stacking = 368×2×9.81×0.30÷10 830 = 0.200 m, that is, 200 mm. The conclusion is a bit counter-intuitive. Every time the drop height increases by 150 mm, the required buffer stroke increases by 100 mm; to only provide 100 mm of buffer, the drop height must be reduced to 150 mm. The export box is rarely provided with a 200 mm buffer. A more realistic approach is to install buffers and limit blocks in the box to constrain the reducer into a rigid body, write the drop height into the technical agreement, and perform drop tests in accordance with GB/T 4857.5-1992.
Drop height h | Buffer 60mm | Buffer 100mm | Buffer 150mm | Buffer 200mm |
|---|---|---|---|---|
0.15 m | 18.05 kN | 10.83 kN | 7.22kN | 5.42kN |
0.30m | 36.10 kN | 21.66 kN | 14.44kN | 10.83kN |
0.45 m | 54.15kN | 32.49kN | 21.66 kN | 16.25kN |
0.60m | 72.20kN | 43.32kN | 28.88kN | 21.66kN |
The peak resultant force in the table is F = m×2gh/s.
3. Moisture-proof, rust-proof and arrival inspection
The reducer is closed in the box, and the temperature difference between day and night will cause condensation on the inside of the box wall. The factory anti-rust oil cannot stop the rust on the tooth surface when the humidity fluctuates repeatedly. The method is to anti-rust the body and seal it, dry the box before packing, add gas-phase anti-rust materials or vacuum bags and add desiccant inside the box, make the box moisture-proof and keep the vents unobstructed, and verify according to GB/T 4857.9-2008 spray test.
Check the box mark and the contract packing list to see if the IPPC mark is clear and on two opposite sides;
Before unpacking, take photos to record the appearance of the box and traces of moisture and impact;
After unpacking, check the rust prevention status, tooth surface, bearings, oil seals and output shaft for collision;
Check that the nameplate parameters (speed ratio, torque, insulation level, protection level) are consistent with the order;
Check the random documents and buffer materials, and report any missing parts in a timely manner.
in conclusion
The mark is GB/T 191-2025, the quarantine is ISPM 15, the test is GB/T 4857 series, and the rest is the strength calculated according to the working conditions. Taking this 320 kg reducer as an example, the stacking load of 10 830 N and the maximum sling force of 45° lifting of 1 430 N are easily solved. The real control condition is the drop impact: when dropped from 300 mm with 100 mm buffer, the peak resultant force is 21 660 N, which is 2 times the stacking load and 6 times the dead weight of the box. Writing these three numbers into the technical agreement is much more useful than writing a sturdy wooden box on the packing list. If you need to calculate the export packaging plan according to working conditions, or choose matching models for hard tooth surface reducers, worm gear reducers, and cycloidal pinwheel reducers, you can contact Hangzhou Weigao Transmission.