How to choose an extruder reducer: key points for checking thrust load, speed ratio and thermal power - Hangzhou Weigao Transmission

Publish Time: 2026-10-17     Origin: Site

The difference between extruder reducer and ordinary reducer: axial thrust is the watershed

When selecting for a single-screw extruder an extruder reducer , many purchasers will directly compare the power with samples of ordinary hard-tooth surface reducers. As a result, abnormal bearing noise and even output shaft movement will occur soon after the equipment is running. The problem lies in the understanding of the working conditions: when the screw pushes the melt in the barrel, it will generate a continuous reverse thrust force along the axis. The higher the barrel pressure, the greater the reverse thrust force. Ordinary reducers do not have a corresponding load path, and this force will damage the bearings sooner or later. Therefore, the industry standard practice is to use a special reducer for extruders (ZLYJ/ZSYJ series, with thrust package structure). The differences between the two are as follows:

Comparative item

Ordinary hard tooth surface reducer

ZLYJ special reducer for extruder

Axial thrust load

There is no special thrust bearing, and the axial force can easily damage the output shaft.

The front end of the hollow output shaft is equipped with a large-size thrust bearing (294 series spherical roller)

Output shaft form

Mainly solid shaft

Hollow shaft (single key/spline/square hole), directly assembled with screw

Gear accuracy and hardness

Depends on series

Carburized and quenched gear grinding, level 6 precision, tooth surface hardness HRC54~62

Adaptation speed

wider range

Input ≤1500r/min, output about 15~120r/min

Thrust bearing: the load-bearing gate of extruder reducer

The key to the structure of the extruder reducer is the thrust bearing group at the front end of the hollow output shaft. According to industry design data, the theoretical life of the thrust bearing of small-sized models such as 133 and 146 is about 12,000 hours, and most other specifications can reach about 25,000 hours - provided that the actual axial force does not exceed the allowable value. It should be reminded that the impact of a rubber extruder is stronger than that of a plastic extruder, and the nature of the load is different. The actual pressure peak and torque spectrum should be provided to the manufacturer for recalculation. You cannot simply apply the parameters of the plastic machine.

Reducer Selection Calculation Step 1: Match the speed ratio with the screw speed

The extrusion process usually requires the screw speed to be adjustable between 15~120r/min, and the motor input speed is mostly 1000~1500r/min. The speed ratio range of ZLYJ series reducer is 8~20, with four commonly used gears: 10, 12.5, 14, and 16. Taking the input of 1000r/min and the output of 70r/min as an example, i=1000/70≈14.3, and the standard speed ratio is 14. After the speed ratio is determined, the output speed is directly linked to the process capacity. It is recommended to confirm the commonly used speed points with the process personnel in the Selection stage to avoid long-term deviation from high-efficiency range operation.

Mechanical power and reducer service coefficient check

Calculate the use torque according to the formula T2=9550×P/n2 (P is the motor power kW, n2 is the output speed r/min). Taking 90kW and output 135r/min as an example, T2=9550×90/135≈6367N·m; if the rated torque of the selected model is 10kN·m, the service coefficient of the reducer Fs=10/6.37≈1.57, which is more reasonable for continuous operation of extrusion conditions. The extruder is a 24-hour continuous production equipment, and it is generally recommended that Fs be no less than 1.5; if the material has high viscosity and frequent starts and stops, it should be further enlarged.

How to calculate axial thrust: an applicable formula

The axial thrust can be estimated based on the screw end area and melt pressure:

Fa (kN) = π × ds² × PS / 4000 (ds is the screw diameter mm, PS is the die melt pressure MPa)

For example: screw diameter 100mm, melt pressure 20MPa, Fa = 3.1416×10000×20/4000 ≈ 157kN. Compare 157kN with the allowable axial thrust of the target model, and check whether the thrust bearing model is sufficient according to the required bearing life (commonly 25000h); if the value is close to critical, the machine frame size should be increased by one gear. Before ordering, check the hollow output shaft aperture, key width or spline parameters, shaft hole depth and foot hole size to ensure direct connection with the screw assembly.

Thermal power calibration and lubrication cooling configuration

The extruder runs continuously, and the cause of the reducer heating is mostly due to the lack of thermal power calibration: sufficient mechanical power does not mean sufficient heat dissipation. Small-sized models can use oil pool splash lubrication and natural cooling; large-sized models (such as ZLYJ280 and above) need to be equipped with oil pumps for forced circulation lubrication, and install a water cooler if necessary. The commonly used lubricating oil is medium extreme pressure gear oil N220; when the ambient temperature is below 0°C, the lubricating oil should be preheated to above 0°C before starting. It is recommended to configure an electric heating tube in cold areas.

Checking steps

content

Judgment basis

Step One: Speed ​​Ratio

Select standard speed ratio (8~20) according to input/output speed

The output speed falls within the common process range

Step 2: Mechanical Power

Calculate the operating torque and select the model by looking up the table

Service factor Fs ≥1.5 (continuous working conditions)

Step Three: Axial Thrust

Fa=π×ds²×PS/4000, compared with the allowable thrust

Allowable thrust > Fa, and meets bearing life requirements

Step Four: Connection Dimensions

Check hollow shaft bore diameter, key/spline, anchor hole

Matches the screw assembly and installation foundation

Step Five: Thermal Power and Cooling

Determine lubrication method and cooling configuration

The oil temperature is stable and does not overheat during continuous operation.

To sum up, whether an extruder reducer can run for a long time depends on whether the four checks of speed ratio matching, service coefficient, axial thrust and thermal power are completed. Hangzhou Weigao Transmission provides a complete product line of hard-tooth surface cylindrical gear reducers, extruder-specific reducers, cycloidal pinwheel reducers and gear reduction motors, etc. It supports reducer customization and thrust bearing configuration calculation according to screw diameter, melt pressure and speed requirements. If you are designing an extrusion production line, you are welcome to contact this local reducer manufacturer in Hangzhou for reducer consultation . Engineers can issue a complete calibration plan based on your actual working conditions within 24 hours; local customers can also search for Hangzhou reducer manufacturers to arrange on-site technical exchanges.

FEEDBACK

Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand

How to check the carrying capacity of worm gear reducer: working condition coefficient, efficiency and Selection calculation example - Hangzhou Weigao Transmission

Lubrication and maintenance characteristics of B series industrial gearboxes

What are the common misunderstandings in B series gearbox maintenance?

Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor