How to check if the abnormal noise and vibration of the reducer exceed the standard: measuring point layout, standard limits and preliminary judgment of spectrum - Hangzhou Weigao Transmission

Publish Time: 2026-10-21     Origin: Site

Once during operation the reducer has abnormal noise or a significant increase in vibration , the response of most on-site personnel is to 'listen first, then touch.' However, auscultation can only be qualitative, and it is difficult to answer such decision-making questions as 'can it continue to operate and to what extent it needs to be repaired?' The standard approach is to use vibration detection to quantify the status: determine the overall health according to standard limits, and then use the spectrum to initially determine the faulty component. This article gives the complete process of measuring point layout, limit value comparison and characteristic frequency interpretation for reference by equipment maintenance personnel.

1. Why measure vibration speed: effective value RMS and judgment standard

The core parameter of reducer vibration detection is the effective value of vibration speed (RMS, unit mm/s). The applicable standard is GB/T 6075.3 (equivalent to ISO 10816-3), covering general industrial reducers from 600 to 3600 r/min. Vibration speed reflects the energy of displacement and frequency at the same time, and can better represent the comprehensive state of gears and bearings than displacement or acceleration alone. For low-speed and heavy-duty models with rotational speeds below 600 r/min, it is recommended to additionally measure the vibration displacement (peak to peak value ≤ 100 μm); for high-frequency micro-impacts such as early pitting corrosion of bearings, it can assist in measuring the vibration acceleration peak value.

2. Vibration limit comparison table: qualified, early warning and shutdown lines

According to GB/T 6075.3 / ISO 10816-3, general industrial reducers (hard tooth surface reducers, cycloidal pinwheel reducers, etc.) are judged in four levels according to the effective value of vibration speed:

status level

Vibration speed effective value (mm/s)

Judgment and Disposal

Excellent (precision grade)

≤2.8

Recommended levels for new machines leaving the factory, servo/planetary and other precision transmissions

Good (regular grade)

2.8~4.5

Normal allowable range of ordinary industrial reducers

Early warning (critical level)

4.5~7.1

Encrypt the frequency of detection and arrange for troubleshooting without stopping the machine temporarily

Danger (shutdown level)

>7.1

Immediately shut down the machine for maintenance to avoid extended damage to gears, bearings and shafting systems.

Industry-specific requirements should take precedence over general standards: the qualified value of the lifting machinery reducer (JB/T 10817) is ≤4.0 mm/s; mining machinery can be relaxed to ≤6.0 mm/s under severe working conditions, but must still be shut down if it exceeds 7.1 mm/s; precision reducers for robots and CNC machine tools are ≤1.5 mm/s, and anything exceeding 2.8 mm/s is considered abnormal; explosion-proof environments are recommended to be controlled at ≤3.5 mm/s.

3. Measuring point layout: three measuring points, three directions, take the larger value

The prerequisite for limit value determination is accurate measurement. The standard measuring points are the input end bearing seat, the output end bearing seat, and the middle of the box (near the gear meshing area). Each measuring point must be measured in three directions: horizontal, vertical, and axial, and the larger value of the three locations is used for judgment. Operation points:

  • The sensor is magnetically attracted or attached to a clean, flat metal surface, avoiding paint and oil stains, otherwise the high-frequency signal will be severely attenuated;

  • Measure 3 times in each direction and take the average value. If the repeatability is poor, check whether the measuring point falls on the thin wall or rib plate;

  • Measured under stable load conditions, no-load data and loaded data cannot be directly mixed;

  • Simultaneously record the speed, oil temperature and ambient temperature to facilitate trend comparison.

4. Preliminary judgment of spectrum: comparison of five types of characteristic frequencies

After the overall value exceeds the standard, use a detector with FFT function to view the spectrum and locate the components according to the characteristic frequency:

Spectral characteristics

pointed fault

On-site evidence

1x frequency conversion (1X) amplitude dominant

Rotor unbalanced

Large radial vibration and stable phase

The peak value of 2x frequency conversion (2X) is increased, and the axial direction is significant.

Coupling misalignment, shaft bending

Use laser alignment instrument to re-measure radial/angular deviation

The meshing frequency (number of teeth × rotation frequency) and harmonics increase, and side frequency bands appear on both sides with intervals of rotation frequency.

Tooth surface wear, reducer gear pitting or eccentricity

Auscultate for rhythmic "clicking" sounds

Peaks and harmonics appear at the bearing characteristic frequency (BPFO/BPFI/BSF/FTF)

Bearing inner and outer rings, rolling elements or cage damage

High-frequency acceleration energy rises, sharp sound

0.5X, 1.5X and other fractional harmonics, phase instability

Loose anchor bolts and insufficient foundation stiffness

After tightening, the vibration value dropped significantly.

Among them, the meshing frequency sidebands and the bearing characteristic frequency are the key clues to determine "whether parts should be replaced": the sideband interval corresponds to which shaft"s rotation frequency, and the defect is on the gear of that shaft.

5. Trend comparison and judgment logic: more important than a single value

The decision cannot be made by looking at the data only once. After establishing a vibration baseline file for each piece of equipment, if the current value rises by more than 30% compared to the historical average, it should be included in the investigation even if it is still in the 'good' range; a sustained slow increase in the value indicates that the fault is developing, and a sudden increase often corresponds to pitting, spalling or broken teeth. Can be judged in conjunction with temperature: Vibration intensification is accompanied by an abnormal rise in oil temperature, which is mostly due to lubrication failure or bearing damage. Refer to the article ' After confirming the spectrum direction, handle it according to the corresponding process - for bearing problems, refer to the Causes of Heating in Reducers' to troubleshoot factors on the lubrication side. reducer bearing replacement specifications. For tooth surface pitting, evaluate the wear amount and repair boundary, and arrange for reducer repair or complete machine replacement if necessary.

6. Incorporate vibration detection into maintenance rhythm

It is recommended that vibration detection be included in the daily reducer maintenance plan: key equipment is collected once a month, general equipment is collected once a quarter, and the data is entered into the ledger to draw a trend curve; early warning equipment is encrypted to weekly. Retest after each maintenance (oil change, bearing replacement, re-alignment) to form a comparison before and after the maintenance, gradually accumulate the normal value range of each model, and the judgment of abnormal noise and vibration problems will become more and more based.

—

Hangzhou Weigao Transmission supplies hard tooth surface gear reducers, cycloidal pinwheel reducers, worm gear reducers and gear reduction motors all year round, with supporting Selection calculations, thermal power calibration and on-site fault diagnosis support. If you are troubleshooting the problem of abnormal noise or excessive vibration of the reducer , or need the Hangzhou reducer manufacturer to directly connect with the reducer manufacturer to provide Selection alternatives, welcome to provide model and working condition parameters, we provide free reducer Selection consultation and quotation services.

FEEDBACK

Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand

How to check the carrying capacity of worm gear reducer: working condition coefficient, efficiency and Selection calculation example - Hangzhou Weigao Transmission

Lubrication and maintenance characteristics of B series industrial gearboxes

What are the common misunderstandings in B series gearbox maintenance?

Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor