How to calculate the tooth surface contact stress of the cycloidal pinwheel reducer: Calculation example of force distribution and load-carrying capacity of the pin tooth pin - Hangzhou Weigao Transmission
Publish Time: 2026-11-10 Origin: Site
The sample of the cycloidal pinwheel reducer is marked with the rated output torque, but few people explain clearly: how this torque is divided among dozens of pin teeth, which tooth is the most demanding, and how to calculate the tooth surface contact stress. The load-bearing capacity of a cycloid pinwheel does not depend on the strength of a single tooth, but on whether the force distribution of a group of pin teeth is even. Once the load is concentrated on a few teeth, no matter how hard the material is, pitting will be formed at that place first. This article uses two sets of calculation examples from the public literature to complete this chain.
1. The force characteristics of the cycloidal pinwheel: a group of teeth share the load, and the load is unevenly distributed
1.1 Tooth number difference and short amplitude coefficient
The cycloidal pinwheel is a KHV type planetary transmission with small tooth difference. The number of pin teeth z p and the number of teeth of the cycloidal wheel z c are only one tooth apart. This is the key to achieving a large speed ratio. The shape of the tooth profile is determined by the short amplitude coefficient K 1 = e·z p /r p , where e is the eccentricity and r p is the radius of the pin tooth center circle; 1 the larger K, the fuller the tooth profile and the thicker the tooth root. The load-bearing capacity is also related to the radius of curvature ρ: if ρ is positive, it means that the tooth surface is convex, and if it is negative, it means that it is concave. When ρ approaches zero, 'top cutting' will occur, that is, the equidistant curve cannot be realized, and a piece of the tooth surface is cut off.
1.2 Contact stress formula and load distribution
The tooth surface contact stress is calculated according to Hertzian contact theory: σ H = 0.418·√(E d ·F i /(b c ·ρ ei )), where E d is the equivalent elastic modulus (take 2.06×10 MPa when both materials are bearing steel 5 ), F i is the meshing force of the i-th tooth, b c is the cycloid tooth width, ρ ei = |ρ·r rp /(ρ − r rp )| is the equivalent radius of curvature. Looking back, σ H 2 ∝ F i ·ρ ei , so in the section where ρ ei does not change much, the load share is proportional to the square of the contact stress - this is the basis of the back calculation in this article. Theoretically, the number of teeth meshing at the same time is about half of the number of pin teeth, but the force on each tooth is not equal.
2. Calculation example: load distribution of 57-tooth cycloidal wheel
2.1 Known conditions and parameters
The calculation example is taken from the cycloidal wheel parameters verified by finite element in the public literature. The tooth profile adopts the equidistant modification amount Δr rp = 0.003 mm and the offset modification amount Δr p = −0.002 mm.
project | symbol | numerical value | unit | illustrate |
|---|---|---|---|---|
Number of needle teeth | z p | 57 | — | Evenly distributed on the needle tooth shell |
Number of cycloid gear teeth | z c | 56 | — | Teeth difference 1 |
Needle center circle radius | r p | 35 | mm | The circle where the pin center is located |
Pin radius | r r | 1.2 | mm | rolling pin, rolling contact |
eccentricity | e | 0.45 | mm | Double eccentric misalignment 180° |
Cycloid tooth width | b | 9 | mm | Enter stress formula |
Modulus of elasticity/Poisson"s ratio | E/μ | 2.19×10 5 /0.28 | MPa / — | Two pieces of the same material |
Rated output torque | T | 50 | N·m | Output |
short amplitude coefficient | K 1 = e·z p /r p | 0.7329 | — | 0.45×57/35 |
Theoretical number of teeth meshing simultaneously | z p /2 | 28.5 | 齿 | About half of the gear teeth carry |
2.2 Tooth-by-tooth stress and load share
The tooth-by-tooth contact stress calculated based on the above parameters is as follows: 14 teeth participate in meshing and 10 teeth are not loaded. The No. 11 tooth with the highest contact stress reaches 924.93 MPa, the average non-zero tooth is 646.08 MPa, and the stress concentration coefficient σ max /σ mean = 1.4316. The load share is inferred from σ i 2 : the peak tooth bears 12.92% of the total circumferential force, but when 14 teeth are shared equally, each tooth only accounts for 7.14%. The peak tooth is 1.809 times the average tooth; teeth No. 4 and No. 17 at both ends only account for 0.55% and 1.57%.
Needle tooth serial number | Contact stress σ i (MPa) | Load share (%) | relatively average teeth |
|---|---|---|---|
4 | 190.16 | 0.55 | 0.076 |
5 | 328.56 | 1.63 | 0.228 |
6 | 470.39 | 3.34 | 0.468 |
7 | 612.85 | 5.67 | 0.794 |
8 | 742.99 | 8.34 | 1.167 |
9 | 844.95 | 10.78 | 1.509 |
10 | 906.78 | 12.42 | 1.738 |
11 (peak) | 924.93 | 12.92 | 1.809 |
12 | 903.32 | 12.32 | 1.725 |
13 | 848.86 | 10.88 | 1.523 |
14 | 767.24 | 8.89 | 1.245 |
15 | 660.12 | 6.58 | 0.921 |
16 | 521.67 | 4.11 | 0.575 |
17 | 322.33 | 1.57 | 0.220 |
3. Back calculation of load carrying capacity: allowable torque, tooth width and modification
3.1 Back calculation of allowable torque
The contact stress and torque have a square root relationship: σ max ∝ √T. Based on this, the allowable torque multiple k = ([σ is back-calculated from the allowable contact stress H ]/σ max ) 2. Taking the 50 N·m of the calculation example as the benchmark, when both the cycloidal wheel and the pin teeth are made of GCr15 and the quenching hardness is 58~62 HRC, the allowable contact stress is 1000~1200 MPa, the multiple is 1.1689~1.6832, and the corresponding allowable output torque is 58.45~84.16 N·m; use 20CrMnMo instead. When the cycloidal wheel is allowed to be 1268 MPa, the multiple rises to 1.8794 and the torque is 93.97 N·m.
3.2 Comparison of tooth width and modification
The contact stress is also inversely proportional to the square root of the tooth width: σ max ∝ 1/√b. Widening the tooth width can increase the load capacity without changing the material, but the cost is the thickness and axial size of the cycloidal wheel. What is more effective is to adapt the tooth profile to the load distribution: equal distance plus displacement modification is a common solution, and segmented modification is processed according to whether the tooth profile participates in the work zone.
Cycloid tooth width b (mm) | Peak contact stress (MPa) | Allowable torque multiple k | Corresponding allowable output torque (N·m) |
|---|---|---|---|
9 (baseline) | 924.93 | 1.1689 | 58.45 |
10 | 877.47 | 1.2988 | 64.94 |
12 | 801.01 | 1.5586 | 77.93 |
15 | 716.45 | 1.9482 | 97.41 |
18 | 654.02 | 2.3378 | 116.89 |
Comparative item | Isometric + shift modification | Sectional modification with equal contact stress | change |
|---|---|---|---|
Peak contact stress (MPa) | 924.93 | 706.39 | down 23.63% |
Non-zero tooth average stress (MPa) | 646.08 | 582.86 | down 9.79% |
Stress standard deviation (MPa) | 244.6 | 193.99 | down 20.69% |
Number of teeth participating in meshing (teeth) | 14 | 20 | Add 6 teeth |
stress concentration factor | 1.4316 | 1.2119 | — |
load concentration factor | 2.0495 | 1.4688 | down 28.33% |
Allowable torque multiple k | 1.1689 | 2.0041 | Rising to 1.7145 times |
The value of segmental modification does not lie in reducing the peak value, but in spreading the load: the number of load-bearing teeth is increased from 14 to 20, the load concentration coefficient is reduced by 28.33%, and the standard deviation is reduced by 20.69%. The increased number of load-bearing teeth means that failure of a single tooth is no longer fatal.
4. The second set of calculation examples
In order to verify that the above distribution law is not an isolated case, another set of publicly available high-stress acceleration test examples is taken: RV-20E reducer, rated load 167 N·m, acceleration load 412 N·m (acceleration factor 2.467), cycloid tooth number z c = 39, pin tooth number z p = 40, pin tooth center circle radius r p = 52 mm, tooth width w = 8.8 mm. It is calculated that 16 pin teeth participate in meshing, the peak force is 600.9939 N, and the maximum stress is 1147.937 MPa.
Do a geometric check first: eccentricity e = r p /z p = 52/40 = 1.3 mm, cycloid pitch circle radius r c ' = e·z c = 50.7 mm, and r p − r c ' = 1.3 mm = e, self-consistent. The wheel bears torque T C = 0.55T = 226.6 N·m, and the total circumferential force is 4469.4 N. The peak tooth accounts for 13.45% of the wheel's circumferential force - which is mutually confirmed with the 12.92% of the previous example, indicating that 'the peak tooth bears about one-seventh of the total load' is a general rule. Strength check: the allowable contact stress of the cycloidal wheel is 1268 MPa, and the safety factor is 1.1046; the pin teeth are GCr15, the allowable contact stress is 3636 MPa, and the safety factor is 3.1674. It can be seen that the tooth surface of the cycloidal wheel is the weak link. Back calculation allows the load torque = 412×(1268/1147.937) 2 = 502.69 N·m, leaving a reserve of 3.01 times relative to the rated torque of 167 N·m. This set of calculation examples also back-calculated ρ e = E d ·F·0.418²/(b·σ²) = 1.8654 mm.
5. Selection Verification steps
Fixed number of teeth and tooth width. Determine z p , z c (the difference in number of teeth is 1) and tooth width b according to the output torque and speed ratio , and calculate whether ρ is close to zero.
Calculate tooth-by-tooth contact stress. Calculate σ H (φ) according to the Hertz formula to find the peak tooth number and stress. Don't just look at the average value.
Calculate load distribution. Inversely estimate the load share from σ i 2 , and check whether the peak tooth exceeds 1.5 times the average tooth; if it exceeds, it means that the number of load-bearing teeth is too small, and it should be improved by modifying or widening the tooth width.
Back calculate the allowable torque. The allowable output torque is obtained from k = ([σ H ]/σ max 2 ) , and compared with the working condition requirements; the robot joints can be compared with the acceleration torque of GB/T 37165-2018.
Review pin tooth pin stiffness. When the span is large, excessive deformation of the pin tooth pin will cause the pin sleeve to glue, and the bending stress and rotation angle need to be checked (the allowable bending stress of GCr15 is 150~200 MPa, the allowable rotation angle is 0.001~0.003 rad); if the diameter of the pin tooth center circle is less than 390 mm, use two fulcrums, and if it reaches 390 mm, use three fulcrums.
Standards can be found: GB/T 10107.1-2012, GB/T 10107.2-2012, GB/T 10107.3-2012 "Cycloidal Pinwheel Planetary Transmission" three parts are all current; accuracy testing follows JB/T 10419-2005; robot joint models follow GB/T 37165-2018 "Precision Cycloidal Pinwheel Reducer for Robots" stipulates that the efficiency shall not be less than 70%, the rated life shall not be less than 6000 h, the heat treatment shall comply with GB/T 34891, and the shell temperature shall not exceed 65 ℃; industrial models shall comply with JB/T 2982-2016.
The load-bearing advantage of the cycloidal pinwheel comes from multi-tooth sharing, but the shortcoming is also here: although there are many teeth, the load is concentrated on the peak tooth. In the first calculation example, the peak tooth bears 12.92% of the circumferential force and the stress concentration coefficient is 1.4316. In the second example, it is independently verified to be 13.45%. If you understand these two numbers, you will understand why a reducer with "sufficient nominal torque" will still pit repeatedly at a fixed position - the problem is not the total load, but the distribution. The path is clear: Calculate the tooth-by-tooth stress to find the peak tooth, and then spread the load from the three directions of tooth width, modification, and number of teeth.
If you need to calculate the load-bearing capacity, tooth width and tooth number configuration of the cycloidal pinwheel reducer according to specific working conditions, or compare and replace imported models, you can contact Hangzhou Weigao Transmission. We manufacture cycloidal pinwheel reducers, hard tooth surface reducers, worm gear reducers and gear reduction motors, and can issue accounting opinions based on torque, tooth width, accuracy grade and temperature rise.