Detailed explanation of the calculation method of reducer speed ratio: formula, multi-stage distribution and comparison of common speed ratios - Hangzhou Weigao Transmission

Publish Time: 2026-10-19     Origin: Site

Reducer speed ratio calculation: starting point of Selection, first find out what it determines

Speed ​​ratio (transmission ratio) refers to the ratio of input speed to output speed, represented by the symbol i. For example, if the input is 1440 r/min and the output is 48 r/min, then i=30:1. The speed ratio calculation of the reducer determines how the motor speed is mapped to the speed of the working mechanism, and also directly determines the amplification factor of the output torque. If the speed ratio is too small, the output speed will be high and the torque will be insufficient; if the speed ratio is too large, the equipment size, cost and heat will increase. This article compiles the commonly used reducer speed ratio calculation formulas , multi-stage speed ratio distribution principles and common speed ratio ranges of various types of reducers into tables for on-site comparison.

1. Four commonly used algorithms for speed ratio

The speed ratio of the same equipment can be calculated from the four entrances of rotation speed, number of teeth, wheel diameter or torque. The results should be verified with each other:

method

formula

Applicable scenarios

Definition

i = n₁ / n₂ (input speed ÷ output speed)

Known motor pole number and working condition required speed

tooth number method

i = z₂ / z₁ (number of driven gear teeth ÷ number of driving gear teeth)

Check drawings or take inventory of gear parameters on site

wheel diameter method

i = D₂ / D₁ (driven wheel diameter ÷ driving wheel diameter)

Friction or flexible transmission links such as belts and chains

Torque inverse algorithm

i = T₂ × n₁ / (9550 × P₁ × η)

A renovation project that only knows load torque and power

For multi-stage transmissions, first calculate the speed ratio of each stage according to the above formula. The total speed ratio is equal to the product of the speed ratios of each stage. For example, in a two-stage transmission i₁=6 and i₂=5, the total speed ratio is i=30.

2. Determine the output torque from the speed ratio

Selection The more common direction is to know the working condition reverse thrust ratio and then calculate the torque. This requires the reducer torque calculation formula: T₂ = 9550 × P₁ × i × η / n₁, where P₁ is the motor power (kW), n₁ is the input speed (r/min), η For transmission efficiency - cylindrical gear transmission generally takes 0.94~0.98, and worm gear transmission only takes 0.65~0.80. This is also the reason why the worm gear structure loses points in high-power situations. After completing the calculation of the reducer output torque, it must be compared with the load peak torque (including starting and impact conditions), and a working condition coefficient of 1.2~1.5 should be introduced if necessary.

3. Distribution principle of multi-stage speed ratio

When the speed ratio needs to be implemented in stages, it is not arbitrary how to divide the levels. The industry usually follows three principles:

  • Principle of equal strength: The load-bearing capacity and life of the reducer depend on the weaker first-level gear. When distributing, the tooth surface contact strength of each level should be as close as possible to avoid a certain level becoming a shortcoming.

  • The principle of small in the front and large in the back: gradually increase the speed ratio from the high speed stage to the low speed stage, and the difference between the two adjacent stages should not be too large. In this way, the speed of the intermediate shaft is higher, the torque is smaller, and the size of the shaft system parts is compact, which is also beneficial to reducing the noise and vibration caused by the peripheral speed.

  • Principle of similar oil immersion depth: When using oil bath lubrication, make the diameters of large gears at all levels close and the oil immersion depth roughly the same, which can reduce the oil churning loss of low-speed large gears.

4. Comparison table of commonly used speed ratio ranges

After calculating the required speed ratio, it must be mapped to the standard gear of the specific model:

type

Single stage common speed ratio

multi-level combination

illustrate

Hard tooth surface cylindrical gear reducer

3~8

Level two and level three can reach hundreds

High efficiency, dense speed ratio and strong versatility

Planetary reducer

3~10

Multiple levels up to hundreds

Compact structure, suitable for servo and precision applications

Cycloid pin wheel reducer

11~87

Two levels 121~5133

Standard speed ratio: 11, 17, 23, 29, 35, 43, 59, 71, 87

Worm gear reducer

10~80

The combination can be larger

A single stage can achieve a large speed ratio, but the efficiency is low

Note that the speed ratio on the nameplate of the cycloidal pinwheel reducer is often marked with an integer rounded. For example, the actual 28.13 will be marked as 28. When calculating the output speed, actual measurement or sample data should prevail.

5. Example: Reverse the speed ratio from the operating speed

A certain conveyor line uses a 4-pole motor (synchronous speed 1500 r/min, full load about 1440 r/min), and the roller requirement is 48 r/min. By definition i = 1440 / 48 = 30. Mapping model: Optional two-stage hard tooth surface gear reducer, i₁=6, i₂=5 according to the front small and the rear large; if the space is limited or a larger speed ratio is required, a two-stage cycloidal pinwheel structure (such as a 5×6 gear combination) can be used. After the speed ratio is rounded, the output speed is about 48 r/min. Then calculate whether the output torque covers the load peak according to the formula in Section 2.

6. Three checks after speed ratio calculation

  • Rounding to standard gear: Try to choose the standard value in the sample for the actual speed ratio. Non-standard speed ratio will extend the delivery time and increase the cost; after rounding, recalculate the output speed and confirm the allowable deviation range of the equipment.

  • Double calibration of torque and thermal power: the speed ratio amplifies the torque, but also changes the load distribution of gears at all levels; thermal power calibration is also required under continuous heavy load conditions to avoid 'enough mechanical power and excessive temperature rise'.

  • Review of radial and axial loads: The cantilever load of the output shaft changes with the working conditions. After the speed ratio is determined, it should be reviewed whether the radial force and axial force of the shaft extension are within the allowable range.

Conclusion

Only by making a solid calculation of the speed ratio of the reducer can we have reliable input for subsequent torque, thermal power and life check. If you are unsure about speed ratio allocation and model mapping, please contact Hangzhou Weigao Transmission . As that produces cycloidal pinwheel reducers, a reducer manufacturer hard tooth surface reducers , gear reduction motors, and worm gear reducers , we provide reducer consultation and free services covering multiple product lines : Send us the motor power, number of poles, and operating speed, and our engineers can help you complete speed ratio matching and torque verification, and issue a Selection plan. If you have any customization needs for the reducer (non-standard speed ratio, change of installation form), you can also negotiate directly.

FEEDBACK

Offshore Wind Vessel Gearbox Market 2027: Crane and Winch Drive Demand

How to check the carrying capacity of worm gear reducer: working condition coefficient, efficiency and Selection calculation example - Hangzhou Weigao Transmission

Lubrication and maintenance characteristics of B series industrial gearboxes

What are the common misunderstandings in B series gearbox maintenance?

Apron Feeder Gearbox Selection: Chain Pull, Shock Load and Service Factor